Eiki EIP-3000N - Manuals - manualsarea.com

Page 2 - ii; IMPORTANT; • For your assistance in reporting the loss; and of the same rating as above, which is also indicated on the pin

ii IMPORTANT • For your assistance in reporting the loss or theft of your Projector, please recordthe Model and Serial Number located onthe bottom of the projector and retain thisinformation. • Before recycling the packaging, please ensure that you have checked the con-tents of the carton thoroughly...

Page 3 - iii

Page 4 - iv

iv The supplied CD-ROM contains operation instructions in English, German, French,Spanish, Italian and Portuguese. Carefully read through the operation instructions beforeoperating the projector. Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch,Spanisch, Itali...

Page 5 - CONSUMER PRODUCT SAFETY ACT; Introduction; ENGLISH; See bottom of projector.; CAUTION; INFORMATION

1 Before using the projector, please read this owner’s manual carefully. 1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, serviceand labor warranty applicable to your purchase. 2. CONSUMER PRODUCT SAFETY ACT To ensure that you will promptly receive any safety...

Page 6 - Caution Concerning Lamp Replacement; PRODUCT DISPOSAL

2 Caution Concerning Lamp Replacement See “Replacing the Lamp” on page 55 . PRODUCT DISPOSAL This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount ofmercury. Disposal of these materials may be regulated due to environmental considerations.For disposal or recycling...

Page 7 - Using the Menu Screen; How to Read this Owner’s Manual; Info; For Future Reference; N o t e; Index

3 40 Using the Menu Screen Menu Selections (Adjustments) Example: Adjusting “Bright”. • This operation can also be performed by using the buttons on the projector. Press B MENU. • The “Picture” menu screen for the se- lected input mode is displayed. Adjustment buttons( P / R / O / Q ) Example: “Pict...

Page 8 - Contents; Preparing; Adjusting the Projected Image

4 Contents Preparing Introduction How to Read this Owner’s Manual ....... 3 Contents ............................................... 4 IMPORTANT SAFEGUARDS ............... 6How to Access the PDF Owner’s Manuals ............................................ 10 Accessories ................................

Page 9 - Reference; Appendix

5 Reference Appendix Maintenance ....................................... 52Maintenance Indicators ...................... 53Regarding the Lamp ........................... 55 Lamp ..................................................... 55Caution Concerning the Lamp ............ 55Replacing the Lamp .......

Page 10 - IMPORTANT SAFEGUARDS; Grounding or Polarization

6 1. Read Instructions All the safety and operating instructions shouldbe read before the product is operated. 2. Retain Instructions The safety and operating instructions should beretained for future reference. 3. Heed Warnings All warnings on the product and in the operatinginstructions should be ...

Page 13 - Using the projector in other countries

9 ■ When turning off the projector, the cooling fanruns to decrease the internal temperature fora while. Unplug the power cord after the cool-ing fan stops. The period the cooling fan runswill vary, depending on the circumstances andthe internal temperature. Caution regarding usage of the projector ...

Page 14 - Please download Adobe; Accessing the PDF Manuals; How to Access the PDF Owner’s Manuals; For Windows; SETUP MANUAL

10 PDF owner’s manuals in several languages are included in the CD-ROM. To utilizethese manuals, you need to install Adobe ® Reader ® on your computer (Windows ® or Macintosh ® ). Please download Adobe ® Reader ® from the Internet (http://www.adobe.com). Accessing the PDF Manuals How to Access the P...

Page 15 - Accessories; Optional accessory; Supplied accessories

11 Accessories Remote control Two R-6 batteries (“AA” size, UM/SUM-3, HP-7 or similar) Power cord* RGB cable (10 ' (3.0 m)) QCNWGA045WJPZ • Quick Guide• Owner’s manual (this manual and CD-ROM) Optional accessory ■ Lamp unit AH-66271 Supplied accessories For U.S. and Canada, etc. (6 ' (1.8 m)) QACCDA...

Page 16 - Top View; Front View; Numbers in; Part Names and Functions; Projector

12 33 40 53 32 32 30 31 52 30 15 28, 53 40, 51 29, 53 28, 29 40 Top View STANDBY-ON button For turning thepower on andputting theprojector intostandby mode. Lamp indicator Temperature warningindicator Adjustment buttons( P / R / O / Q ) For selecting menu items. Volume buttons(– O / Q +) For adjusti...

Page 17 - Terminals; Rear View; Using the Kensington Lock

13 25 52 31 26 25 25 24 232425 27 21 2324 27 24 46 52 Numbers in Z refer to the main pages in this owner’s manual where the topic is explained. Terminals Rear View Refer to “INPUT Terminals and Connectable Main Equipment” on page 21 . AUDIO (INPUT3, 4) terminal(Shared forINPUT 3 and 4) INPUT 3 termi...

Page 19 - Inserting the Batteries; Attach the cover and slide it until it clicks into place.; Press the; Caution; When using the remote control; Usable Range

15 • Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type. • Insert the batteries making sure the polarities correctly match the m and n marks inside the battery compartment. • Batteries of different types have different properties, therefore do not mi...

Page 20 - Quick Start; Setup and Projection; and; Remove the lens cap and turn the projector on

16 Quick Start This section shows the basic operation (projector connecting with the computer). For details, seethe page described below for each step. Setup and Projection In this section, connection of the projector and the computer is explained using one example. When connecting equipment other t...

Page 21 - Adjust the projected image with the Setup Guide; Select the INPUT mode; Correct trapezoidal distortion

17 4. Adjust the projected image with the Setup Guide Select the “INPUT 1” using the INPUT button on the projector or C INPUT 1 on the remote control. 6. Select the INPUT mode • When pressing the INPUT button on the projector, input mode switches in the following order: INPUT1 INPUT2 INPUT3 INPUT4 •...

Page 22 - Setting up the Projector; Side View; Example of standard setup

18 Ceiling-mount Setup ■ It is recommended that you use the optionalEIKI ceiling-mount bracket for this installation.Before mounting the projector, contact yournearest EIKI Authorized Dealer or ServiceCenter to obtain the recommended ceiling-mount bracket (sold separately). ■ Invert the image by set...

Page 23 - Indication of the Projection Image Size and Projection Distance

19 300" 200" 100" 84"60" 240" ´ 180" 160" ´ 120" 80" ´ 60" 67" ´ 50" 48" ´ 36" 34'3 "–39' 8" (10.4 m – 12.1 m) 22'10 "–26'5 " (7.0 m – 8.1 m) 11'5 "–13'3 " (3.5 m – 4.0 m) 9'7 "–11'1 " (2.9 m – 3.4 m) 6'10 &#...

Page 24 - Screen Size and Projection Distance

20 Setting up the Projector (Continued) 300 (762 cm) 270 (686 cm) 250 (635 cm) 200 (508 cm) 150 (381 cm) 100 (254 cm) 84 (213 cm) 80 (203 cm) 72 (183 cm) 60 (152 cm) 40 (102 cm) 610 cm (240 ) 549 cm (216 ) 508 cm (200 ) 406 cm (160 ) 305 cm (120 ) 203 cm (80 ) 171 cm (67 ) 163 cm (64 ) 146 cm (58 ) ...

Page 25 - Connections; INPUT Terminals and Connectable Main Equipment

21 Connections INPUT Terminals and Connectable Main Equipment INPUT 1, 2 terminal ■ Connecting the computer. (See page 23 .) ■ Connecting video equipment with compo- nent output terminal (DVD player, DTVdecoder, DVD recorder with hard disc,etc.). (See page 24 .) INPUT 3 terminal Connecting video equ...

Page 26 - Samples of Cables for Connection

22 Samples of Cables for Connection Cables for a cameraor a video game Equipment Input Signal Cable Terminal on the projector ø3.5 mm stereo audio cable(commercially available) RGB cable (supplied) S-video cable (commercially available) Video cable (commercially available) Computer Audio-visualequip...

Page 27 - Connecting to a Computer; Supplied

23 Connecting to a Computer To RGB output terminal To audio output terminal RGB Cable * ø3.5 mm stereo ormono audio cable(commerciallyavailable) RGB Cable Before connecting, ensure that the power cord of the projector is unplugged from the ACoutlet and turn off the devices to be connected. After mak...

Page 28 - Connecting to Video Equipment

24 Connecting to Video Equipment The projector is equipped with input terminals that suppor t component, S-video, and video signals.See the illustration below to connect with the audio-visual equipment.The image quality is highest in the order of the component signal, the S-video signal and the vide...

Page 29 - Connecting to a Monitor with RGB Input Terminal

25 L R To video output terminal When using a composite video cable(INPUT4) To audio output terminal N o t e Composite video cable(commercially available) RCA audio cable (com-mercially available) To AUDIO (INPUT 3, 4) terminal To INPUT4terminal Connecting to a Monitor with RGB Input Terminal You can...

Page 30 - Controlling the Projector by a Computer

26 Controlling the Projector by a Computer When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS-232C adaptor and an RS-232C serial control cable (cross type, commercially available), the com-puter can be used to control the projector and check the status of the p...

Page 31 - Connecting the Power Cord; When connecting to the LAN terminal using a LAN cable

27 Connecting the Power Cord Plug the supplied power cord into theAC socket on the rear of the projector.Then plug into AC outlet. AC socket Power cord Supplied accessory When connecting to the LAN terminal using a LAN cable TX/RX LED (yellow)Illuminates when transmit-ting/receiving data. LINK LED (...

Page 32 - Turning the Projector On/Off; R e m o v e t h e l e n s c a p a n d p r e s s; Turning the Projector on; to

28 Turning the Projector On/Off R e m o v e t h e l e n s c a p a n d p r e s s o STANDBY-ON on the projector or f ON on the remote control. • When System Lock is set, the keycode input box appears. To cancel the keycode setting, input thekeycode that you have already set. See page 47 for details. •...

Page 34 - About the Setup Guide; Adjusting the Focus; Image Projection

30 About the Setup Guide After turning on the projector, the SetupGuide screen appears to assist you withprojector setup. Press p ENTER to exit the Setup Guide screen. Guidance items 1 FOCUS2 HEIGHT ADJUST3 ZOOM STANDBY-ONbutton ENTER button 1 Adjusting the Focus You can adjust the focus with the fo...

Page 35 - Adjusting the Height

31 3 Adjusting the Height The height of the projector can be ad-justed using the adjustment feet at thefront and rear of the projector.When the screen is above the projec-tor, the projection image can be madehigher by adjusting the projector. 1 2 3 • Do not apply too much pressure on the pro- jector...

Page 38 - Resize Mode

34 Image Projection (Continued) Resize Mode This function allows you to modify or customize the resize mode to enhance the input image. De-pending on the input signal, you can choose “NORMAL”, “BORDER” or “STRETCH” image. Press H RESIZE. • See page 44 for setting on menu screen. Computer Input Signa...

Page 39 - VIDEO

35 VIDEO • “STRETCH” is fixed when 540P, 720P or 1080 I signals are entered. : Cutout area on which images cannot be projected.: Area on which the image is not included in the original signals. Input Signal DVD / Video Image type Output screen image NORMAL BORDER STRETCH 480 I , 480P, 576 I , 576P, ...

Page 40 - Operating with the Remote Control; Freezing a Moving Image; Selecting the Picture Mode

36 Auto Sync(Auto Sync Adjustment) Operating with the Remote Control Freezing a Moving Image • When the optimum image cannot be achieved with Auto Sync adjustment, use the help menufor manual adjustments. (See page 51 .) Auto Sync function works when detect-ing input signal after the projector turns...

Page 41 - The following shows the items that can be set in the projector.; Menu Items; “Picture” menu

37 The following shows the items that can be set in the projector. Menu Items “Screen adjustment (SCR-ADJ)” menu INPUT 1 (Component)/INPUT 2(Component)/INPUT 3/INPUT 4 INPUT 1 (RGB)/INPUT2 (RGB) “Picture” menu Picture SCR PRJ Net. Picture Mode Contrast 0 0 0 0 K 7 5 0 0 Bright Red Blue 1 CLR Temp Br...

Page 42 - “Network” menu

38 “Projector adjustment (PRJ-ADJ)” menu Pict. Auto Search SCR PRJ - ADJ Net. Auto Sync Auto Power Off System Sound System Lock h On On On On SEL./ADJ. ENTER END 0 Lamp Timer(Life) 100% Help Speaker On RS-232C 9600 bps Fan Mode Normal Disable Main menu Sub menu PRJ - ADJ Page 46 Auto Search [On/Off]...

Page 47 - Progressive; Lamp Setting; Adjusting the Image

43 4 4 4 4 4 Progressive • In NTSC or PAL60Hz, even if the 3D Progres- sive mode has been set, the three-two pulldown enhancement will be enabled automati-cally when the film source has been entered. • When the image is blurred or noisy, switch to the optimal mode. • When using progressive inputs, i...

Page 48 - Setting the Resize Mode; Keystone Correction; Manual Correction

44 Adjusting the Projected Image(“SCR - ADJ” menu) Pict. Resize Image Shift 0 0 SCR - ADJ PRJ Net. Keystone Auto Keystone OSD Display Background Setup Guide PRJ Mode Language Front English On Logo On Off Normal SEL./ADJ. ENTER END Help 8 7 6 5 4 3 2 1 1 1 1 1 1 Setting the Resize Mode • For details ...

Page 50 - Auto Search Function; Speaker Setting

46 Adjusting the Projector Function (“PRJ - ADJ” menu) Auto Search Auto Sync Auto Power Off System Sound System Lock h On On On On SEL./ADJ. ENTER END 0 Lamp Timer(Life) 100% Pict. SCR PRJ - ADJ Net. Help Speaker On RS-232C 9600 bps Fan Mode Normal Disable 1 1 1 1 1 Auto Search Function This functio...

Page 51 - We suggest you record; Select “System Lock”, then press; System Lock Function; Setting/Changing the keycode

47 Info This function prevents unauthorized use of theprojector. Once this function is activated, usersmust enter the correct keycode each time theprojector is turned on. We suggest you record the keycode in a safe place where only au-thorized users have access. • If you lose or forget your keycode,...

Page 52 - Taking the Keylock off

48 N o t e Input screen for keycode To cancel the keycode that you have alreadyset • Press R on the projector for four times in steps 2 and 3 above. When the System Lock is set • When System Lock is set, the keycode input screen appears after the power is turned on.When it appears, enter the right k...

Page 53 - Setting up the Projector Network Environment (“Network” menu); If you forget the password; On the projector, press; Setting a Password

49 Setting up the Projector Network Environment (“Network” menu) If you do not want others to change the settingfor the “Network” menu, set a password. Select “Password”, then press h ENTER or Q . • The screen for entering the password appears. 1 1 1 1 1 1 Setting a Password Press P or R to set the ...

Page 54 - DHCP Client Setting

50 Setting up the Projector Network Environment (“Network” menu)(Continued) Menu operation n Page 40 3 3 3 3 3 TCP/IP Setting 4 4 4 4 4 Confirming theProjector Information You can confirm the MAC address and projectorname. Selectable items IP Address Subnet Mask Gateway Description Factory default s...

Page 55 - Troubleshooting with the “Help” menu

51 Troubleshooting with the “Help” menu Utilizing the “Help” menu func-tions This function advises you to solve the problems during usage. • You can adjust the items with check marks ( ✔ ). • The items in the “Help” menu change, de- pending on the input signal or setting that youhave selected. • I f...

Page 56 - Maintenance

52 Cleaning the lens ■ Use a commercially available blower or lenscleaning paper (for glasses and camera lenses)for cleaning the lens. Do not use any liquid typecleaning agents, as they may wear off thecoating film on the surface of the lens. ■ As the surface of the lens can easily getdamaged, be su...

Page 57 - Maintenance Indicators; About the lamp indicator

53 Maintenance Indicators About the lamp indicator ■ When the remaining lamp life becomes 5% or less, (yellow) and “Change The Lamp” will bedisplayed on the screen. When the percentage becomes 0%, it will change to (red), the lamp willautomatically turn off and then the projector will automatically ...

Page 59 - Regarding the Lamp; Lamp

55 Regarding the Lamp Lamp ■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life becomes5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life(percentage) can be checked with the on-screen display. (see page 4...

Page 60 - Disconnect the power cord.; Optional

56 Regarding the Lamp (Continued) Removing and Installing theLamp Unit • Make sure that you remove the lamp unit by the handle. Do not touch the glass surface ofthe lamp unit or the inside of the projector. • To avoid injury to yourself and damage to the lamp, be sure to carefully follow the stepsbe...

Page 61 - Remove the lamp unit.; Resetting the Lamp Timer; Insert the new lamp unit.

57 Remove the lamp unit. • Loosen the securing screws from the lamp unit. Hold the lamp unit by thehandle and pull it in the direction of thearrow. At this time, keep the lamp unithorizontal and do not tilt it. Resetting the Lamp Timer Reset the lamp timer after replacing the lamp. Insert the new la...

Page 62 - DTV; Computer Compatibility Chart

58 DTV • When this projector receives 640 K 350 VESA format VGA signals, “640 K 400” appears on the screen. • Optimum image quality will be achieved by matching your computer’s output resolution to theprojector’s native resolution (1024 x 768). Computer Computer Compatibility Chart • Multiple signal...

Page 63 - Troubleshooting

59 Troubleshooting No picture and no sound or projector does not start. Sound is heard but no picture appears (or picture is dark). Color is faded or poor. Picture is blurred; noise appears. Picture appears but no sound is heard. An unusual sound is occasionally heard from the cabinet. Maintenance i...

Page 65 - Specifications

61 Specifications ProjectorEIP-3000NNTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAM/DTV480 I /DTV480P/ DTV540P/DTV576 I /DTV576P/DTV720P/DTV1035 I /DTV1080 I /DTV1080 I -50 Single Chip Digital Micromirror Device TM (DMD TM ) by Texas Instruments Panel size: 0.55 " (14 mm), 1chip XGA DMD No. of do...

Page 66 - Dimensions

62 Dimensions Units: inches (mm) M4 M4 M4 M4 12 13 / 32 ( 315) 3 1 / 16 ( 77.5) 2 19 / 32 ( 65.5) 1 53 / 64 ( 46.2) 3 5 / 32 ( 80) 1 55 / 64 ( 47) 2 7 / 8 ( 73) 2 61 / 64 ( 75) 1 11 / 32 ( 33.8) 4 19 / 64 ( 109) 4 9 / 64 ( 105) 1 7 / 8 ( 47.5) 4 7 / 64 ( 104) 7 / 16 ( 11) 11 1 / 32 ( 280) 23 / 64 ( ...