Edimax AR-7211B V2 - Manuals
Edimax AR-7211B V2 – Manual in PDF format online.
Manuals:
Manual Edimax AR-7211B V2
Summary
2 COPYRIGHT Copyright Edimax Technology Co., Ltd. all rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical...
3 Contents 1. PRODUCT INTRODUCTION ..................................................................................................................... 5 1.1. P ACKAGE C ONTENTS ............................................................................................................................
5 1. Product Introduction 1.1. Package Contents Before you start using this product, please check if there is anything missing in the package and contact your dealer to claim the missing item(s): ADSL2+ router (AR-7211A V2 or AR-7211B V2) Power adapter 1 meter RJ-45 Ethernet cable 1.8M RJ-11...
6 Do not put this device close to heat sources or high temperatures. Keep the device out of direct sunshine. Do not put this device close to a place where it is damp or wet. Do not spill any fluid on this device. Do not connect this device to any PCs or electronic products, other than those wh...
7 Internet Green ON Internet connected in router mode BLINK Internet activity (transferring/receiving data) in router mode OFF Device in bridged mode Red ON Internet not connected in router mode (Please refer to Note 2 ) LAN Green ON LAN port connected BLINK LAN activity (transferring/receiving data...
8 1.5. Features The device supports the following features: Various line modes External PPPoE dial-up access Internal PPPoE/PPPoA dial-up access 1483Briged/1483Routed/MER/IPoA access Multiple PVCs (up to eight) which can be isolated from each other A single PVC with multiple sessions M...
9 2. Hardware Installation Step 1. Connect the ADSL line Connect the Line interface of the device to the Modem interface of a splitter using a telephone cable. Connect a telephone to the Phone interface of the splitter using a telephone cable. Connect the Line interface of the splitter to your exist...
10 Figure 1 – No telephone before the splitter Configuration 2 0 shows the correct connection when a telephone set is installed before the splitter. Figure 2 - Telephone set connected before the splitter Note: When Configuration 2 is used, the filter must be installed close to the telephone cable. D...
11 access, or slow connection speed. If you really need to add a telephone set before the splitter, you must add a micro filter before a telephone set. Do not connect several telephones before the splitter or connect several telephones with the micro filter. Step 4. Check the ADSL LED status Please ...
12 2. Click “Switch to Classic View” in the top left to show additional setting icons. 3. Locate the “Network Connections” icon and double-click to open network connection settings.
13 4. Select the “Local Area Connection” icon and right-click it to open the sub- menu, then select “Properties” . 5. Select “Internet Protocol (TCP/IP)” and then click “Properties”
14 6. Ensure that “Obtain an IP address automatically” and “Obtain DNS server address automatically” are selected and then press “OK” .
15 3. IP Address Setting To use the router to access the Internet, the PCs in the network must have an Ethernet adapter installed and be connected to the router either directly or through a hub or switch. The TCP/IP protocol of each PC has to been installed and the IP Address of each PC has to be se...
16 4. In the Internet Protocol Version 4 (TCP/IPv4) Properties window, select Obtain an IP address automatically and Obtain DNS server address automatically as shown on the following screen. 5. Click OK to confirm the setting. Your PC will now obtain an IP address automatically from your router’s DH...
17 3. Check your list of Network Components. You should see Internet Protocol Version 4 (TCP/IPv4) on your list. Select it and click the Properties button. 4. In the Internet Protocol Version 4 (TCP/IPv4) Properties window, select Obtain an IP address automatically and Obtain DNS server address auto...
19 4. EZmax Setup Wizard You can configure the router by running the setup wizard on the CD-ROM included in the package contents. The wizard enables you to configure your Internet connection, upgrade the firmware and change the router’s password. Please follow the instructions below. Alternatively, ...
25 4.2. Internet Connection Type If your country or ISP is not listed, please select “Other” from the list. Then select your Internet connection type and click “Next”. If you are not sure, please contact your Internet Service Provider (ISP). Depending on your selection, please refer to the appropria...
26 Parameter Description PPPoE/PPPoA PPPoE (PPP over Ethernet) and PPPoA (PPP over ATM) are common connection methods used for xDSL. Bridge Mode Bridge Mode is a common connection method used for xDSL modems. Dynamic IP Address Obtain an IP address automatically from your service provider. Static IP...
28 4.2.1.2. Bridge Mode Parameter Description VPI Virtual path identifier (VPI) is the virtual path between two points in an ATM network. Its valid value is in the range of 0 to 255. Enter the correct VPI provided by your ISP. By default, VPI is set to 8. VCI Virtual channel identifier (VCI) is the ...
31 multiplexing. In Bridge Mode, please select “ADSLTYPE_ROUTER_LLC” or “ADSLTYPE_ROUTER_VCMUX”. 4.3. Firmware Upgrade The wizard includes a tool to upgrade the router’s firmware. Firmware can be downloaded from the Edimax website, if you wish to upload new firmware, select “Firmware Upgrade” from t...
32 5. Web Configuration The router can also be configured using the web-based configuration interface. Follow the instructions below. 5.1. Accessing the Router To access the web-based configuration interface: 1. Open the Internet Explorer (IE) browser and enter http://192.168.2.1 . 2. In the Login p...
33 If you log in as a common user, you can check the status of the router, but not configure most of the settings. 5.2. Internet Connection The Wizard page of the web-based interface allows easy configuration of the Internet connection and other parameters. The following sections describe the variou...
37 Field Description address, subnet mask and default gateway for the WAN connection, which is provided by your ISP. Obtain DNS server addresses automatically When selected, DHCP automatically assigns DNS server address. Use the following DNS server addresses When selected, you need to manually ente...
39 Click BACK to modify the settings. Click FINISH to save the settings. Click RESET to cancel the settings. Note: After saving the settings in the W izard page, the PVC in the Wizard page replaces that in the Channel Configuration page. The preset PVCs in the Channel Configuration page do not take ...
42 5.3.5. ARP Choose Status > ARP . In the Arp Table page, you can view the table that shows a list of learned MAC addresses. 5.4. Network In the navigation bar, click Network . The Network page that is displayed contains LAN and WAN . 5.4.1. LAN Choose Network > LAN . The LAN page that is dis...
43 Field Description IP Address Enter the IP address of LAN interface. It is recommended to use an address from a block that is reserved for private use. This address block is 192.168.2.1- 192.168.255.254. Subnet Mask Enter the subnet mask of LAN interface. The range of subnet mask is from 255.255.0...
56 5.5. Service In the navigation bar across the top of the screen, click Service . The Service page which is displayed contains DNS , Firewall , UPNP , IGMP Proxy , TR-069 and ACL . 5.5.1. DNS Domain Name System (DNS) is an Internet service that translates the domain name into IP address. Because t...
62 5.5.4. IGMP Proxy Choose Service > IGMP Proxy , and you will see the following page. An IGMP proxy enables the system to issue IGMP host messages on behalf of hosts that the system discovered through standard IGMP interfaces. The system acts as a proxy for its hosts after you enable it. 5.5.5....
73 5.6.2.5. NAT Exclude IP Click NAT Exclude IP in the left pane, the following screen will be displayed. Here, you can configure some source IP addresses which use the purge route mode when accessing internet through the specified interface. 5.6.2.6. Port Trigger Click Port Trigger in the left pane...
79 5.6.5.2. Client Limit Click Client Limit in the left pane, the page shown in the following figure will appear. This page is used to configure the capability of force how many devices can access to Internet. 5.6.5.3. Others Click Others in the left pane, and you will see the following page. You ca...
87 5.9. Trouble Shooting Question Answer Why are all the indicators off? Check the connection between the power adapter and the power socket. Check whether the power switch is turned on. Why is the LAN indicator off? Check the following: The connection between the device and your PC, hub or sw...
88 Declaration of Conformity We, Edimax Technology Co., LTD., declare under our sole responsibility, that the equipment described below complies with the requirements of the European Council directive (2004/108/EC, 92/31/EEC, 2006/95/EC). Equipment : Fast Ethernet ADSL2/2+ Modem Router Model No. : A...
Edimax Manuals
-
Edimax EW-7711UMN
Manual
-
Edimax PS-1206U
Manual
-
Edimax LAN USB Adapter
Manual
-
Edimax EW-7708Pn
Manual
-
Edimax EW-7748In
Manual
-
Edimax EW-7128g
Manual
-
Edimax PS-1208UWg
Manual
-
Edimax EU-4207
Manual
-
Edimax EW-7727In
Manual
-
Edimax PS-1206PWg
Manual
-
Edimax PS-3103P
Manual
-
Edimax EW-7717Un
Manual
-
Edimax 802.11 b
Manual
-
Edimax EU-4230
Manual
-
Edimax PT-111E
Manual
-
Edimax EN-9130TXA
Manual
-
Edimax IC-7000
Manual
-
Edimax EW-7205AP
Manual
-
Edimax Draft 2.0-N
Manual
-
Edimax PT-31W
Manual