Edimax 3G-6210n - Manuals

CATALOG CHAPTER I: PRODUCT INFORMATION 1-1 Introduction and safety information 1-2 Safety Information 1-3 System Requirements 1-4 Package Contents 1-5 Familiar with your new Portable 3G router CHAPTER II: SYSTEM AND NETWORK SETUP 2-1 Getting Started 2-2 Build network connection 2-3 Connecting to Por...

CHAPTER III: ADVANCED FUNCTIONS 3-1 Quality of Service (QoS) 3-1-1 Basic QoS Settings 3-1-2 Add a new QoS rule 3-2 Network Address Translation (NAT) 3-2-1 Basic NAT Settings (Enable or disable NAT function) 3-2-2 Port Forwarding 3-2-3 Virtual Server 3-2-4 Port Mapping for Special Applications 3-2-5 ...

CHAPTER IV: APPENDIX 4-1 Hardware Specification 4-2 Troubleshooting 4-3 Glossary

1 Chapter I: Product Information 1-1 Introduction and safety information Thank you for purchasing this Portable 3G Router! The smallest router also integrated with Li-battery inside, assists you to set up a wireless network using mobile phone, 3G USB modem or an Ethernet connections anytime and anyw...

6 1-5 Familiar with your new Portable 3G Router LED Definitions LED Name Light Status Description PWR/CHG Green On Router is switched on and correctly powered or the battery is charged completely. Orange On The battery is charging. Orange Flashing Battery power is not enough, only 30 minutes remains...

8 Right and Left Side Panel Item Name Description LAN/WAN Switch Switch the Ethernet port to LAN or WAN. Switch to WAN function if you want to access to the Internet through your xDSL or Cable modem network service. WAN access can also be a back up for 3G network. Please refer to Section 3-4 for mor...

9 Chapter II: System and Network Setup 2-1 Getting Started Before you using the router, please follow the following instructions to charge the router. 1. Remove the battery cover in the rear side of the router and insert the supplied battery into the slot and then put back the cover. 2. Connect the ...

11 2. Use only battery and power adapter supplied with the product. The use of any other types may be dangerous. 2-2 Build network connection Please follow the following instruction to build the network connection between your new portable 3G router and your computers, network devices: 1. Connect yo...

14 2-3 Connecting to Portable 3G Router by web browser After the network connection is built, the next step you should do is setup the router with proper network parameters, so it can work properly in your network environment. Before you can connect to the router and start configuration procedures, ...

24 Input ‘ipconfig’, then press ‘Enter ’ key. Please check the IP address followed by ‘Default Gateway’ (In this example, the IP address of router is 192.168.2.1, please note that this value may be different. ) 3. Connect the router’s management interface by web browser After your computer obtained ...

26 2-4 Using ‘Quick Setup’ This router provides a ‘Quick Setup’ procedure, which will help you to complete all required settings you need to access the Internet in very short time. Please follow the following instructions to complete the ‘Quick Setup’: Please go to QuickSetup menu by clicking ‘Quick...

27 NOTE: There are several time servers available on internet: 129.6.15.28 (time-a.nist.gov) 132.163.4.101 (time-a.timefreq.bldrdoc.gov) 131.107.1.10 (time-nw.nist.gov) If you found that the time of router is incorrect, try another time server.

29 3. Basic Setting Here are descriptions of every setup items: Wireless Module (1): Please click “Enable” to start using the wireless function of this router, or select “Disable” to close the wireless interface of this router. Band (2): Please select a Bane type from the dropdown list of ‘Band’, It...

31 4. Security Settings Please choose the Encryption type you’re using from the dropdown list of “Encryption”. There are three types of Encryption, they are: WEP - Please go to section 2-7-3-2 WPA pre-shared key - Please go to section 2-7-3-3 WPA RADIUS - Please go to section 2-7-3-4 If you want to ...

33 menu. AT Dial Script (7): Please input Dialed Number for your UMTS or HSDPA connection, the default is *99#. This field should not be altered except when required by your service provider. After you finish with all settings, please click ‘Next’ (8) button; if you want to go back to previous menu,...

40 12. The utility of C100S will start up automaticity. Please select the “MENU” 13. Click “Setting”. 14. Select the “Auto connect on startup”.

47 BEZEQ network in Israel. Connection Type (7): Please select the connection type of Internet connection you wish to use, please refer to last section for detailed descriptions. Idle Time Out (8): Please input the idle time out of Internet connection you wish to use, and refer to last section for d...

52 Here are descriptions of every setup items: Time Zone (1): Please select time zone at ‘Time zone’ drop-down list. Time Server Please input the IP address or host name of time Address (2): server here. Daylight Please check ‘Enable’ Function box, and set the Savings (3): duration of daylight setti...

70 Here are descriptions of every setup items: Primary DNS (1): Please input the IP address of DNS server provided by your service provider. Secondary DNS (2): Please input the IP address of another DNS server provided by your service provider, this is optional. After you finish with all settings, p...

72 service provider. Account / Input account or email of DDNS registration. E-Mail (4): Password / Key (5): Input DDNS service password or key. After you finish with all settings, please click ‘Apply’ (6) button and the following message will be displayed on your web browser: Please click ‘Continue’...

73 2-7 Wired LAN Configurations Before all computers using wired Ethernet connection (i.e. those computers connect to this router’s LAN port 1 to 4 by Ethernet cable) can communicate with each other and access internet, they must have a valid IP address. There are two ways to assign IP addresses to ...

74 Please follow the following instructions to set wired LAN parameters: Please click ‘LAN’ menu on the left of web management interface, there are three setup groups here: ‘LAN IP’, ‘DHCP Server’, and ‘Static DHCP Leases Table’. Here are setup instructions for each of them: 2-7-1 LAN IP section: He...

75 2-7-2 DHCP Server: These settings are only available when ‘DHCP Server’ in ‘LAN IP’ section is ‘Enabled’, and here are descriptions of every setup items: Lease Time (1): Please choose a lease time (the duration that every computer can keep a specific IP address) of every IP address assigned by th...

77 After you clicked ‘Add’, the MAC address and IP address mapping will be added to ‘Static DHCP Leases Table’ section. If you want to delete a specific item, please check the ‘Select’ box of a MAC address and IP address mapping (1), then click ‘Delete ’ button (2); if you want to delete all mapping...

78 2-8 Wireless LAN Configurations If your computer, PDA, game console, or other network devices which is equipped with wireless network interface, you can use the wireless function of this router to let them connect to Internet and share resources with other computers with wired-LAN connection. You...

79 Please click ‘Continue’ to back to previous setup menu; to continue on other setup procedures, or click ‘Apply’ to reboot the router so the settings will take effect (Please wait for about 30 seconds while router is rebooting). 2-8-1 Basic Wireless Settings Please click ‘Wireless’ menu on the lef...

86 Here are descriptions of every setup items: Key Length (2): There are two types of WEP key length: 64-bit and 128-bit. Using ‘128-bit’ is safer than ’64-bit’, but will reduce some data transfer performance. Key Format (3): There are two types of key format: ASCII and Hex. When you select a key fo...

89 Key Format (3): can select Passphrase (8 or more alphanumerical characters, up to 63), or Hex (64 characters of 0-9, and a-f). Pre-shared Please input the WPA passphrase here. Key (4): It’s not recommended to use a word that can be found in a dictionary due to security reason. After you finish WP...

95 displayed here. If you don’t enable security function of the wireless router before WPS is activated, the router will auto set the security to WPA (AES) and generate a set of passphrase key for WPS connection. Passphrase Key: The wireless security key of the router will be displayed here. Config ...

97 Chapter III Advanced Functions 3-1 Quality of Service (QoS) Quality of service provides an efficient way for computers on the network to share the internet bandwidth with a promised quality of internet service. Without QoS, all computers and devices on the network will compete with each other to ...

99 Move Up (9): You can pull up the priority of the QoS rule you selected by clicking this button. Move Down (10): You can lower the priority of the QoS rule you selected by clicking this button. After you finish with all settings, please click ‘Apply’ (11) button and the following message will be d...

105 Reset (12): Unselect all mappings. After you finish with all settings, please click ‘Apply’ (13) button and the following message will be displayed on your web browser: Please click ‘Continue’ to back to previous setup menu; to continue on other setup procedures, or click ‘Apply’ to reboot the r...

113 3-3 Firewall Excepting NAT, this router also provides firewall function to block malicious intruders from accessing your computers on local network. These functions include inbound attack prevention, and block outbound traffics, like block URLs which have pre-defined keywords. Please follow the ...

120 Current URL All existing URL/Keywords in filtering Blocking Table (5): table will be listed here. Delete Selected (6): If you want to delete a specific URL/Keyword entry, check the ‘select’ box of the MAC address you want to delete, then click ‘Delete Selected’ button. (You can select more than ...

121 responding because it is not capable to handle too much traffics. This router has a built-in DoS attack prevention mechanism; when you activate it, the router will stop the DoS attack for you. Please follow the following instructions to set DoS prevention parameters: Please click ‘Firewall’ menu...

122 Port Scan (3): Some malicious intruder will try to use a ‘port scanner’ to know how many ports of your Internet IP address are open, and they can collect a lot of valuable information by doing so. Check this box and the router will block all traffics which are trying to scan your Internet IP add...

127 3-4 Fail Over WAN failure detection works by detecting the presence of traffic on the 3G modem link. If the link is idle for too long the router will attempt to ping a target IP address. If the ping does not reply, the router assumes the link is down and attempts to fail over to Ethernet WAN lin...

129 3-5 System Status The functions described here will provide you with system related information. To enter system status menu, please either click ‘Status’ link located at the upper-right corner of web management interface, or click ‘Status’ button in main menu. 3-5-1 System information and firmw...

136 interface, then click ‘Firmware Upgrade’ on the left of web management interface, then the following message will be displayed on your web browser: Please click ‘Next’, and the following message will be displayed: Click ‘Browse’ button first, you’ll be prompted to provide the filename of firmwar...

138 Chapter IV: Appendix 4-1 Hardware Specification Flash: 4MB SDRAM: 16MB Ethernet Port: 10/100M UTP Port x 1 USB Post : USB 2.0 Type A x 1 (3G), Mini USB x 1 (Power) Antenna: Internal Printed Antenna (1T1R) Power: 5VDC, 2A xMini USB Type Switch Power Adaptor Dimension: 16.8(H) x 70(W) x 100(D)mm T...

141 management interface: password is wrong IP address of the router! b. Password is case-sensitive. Make sure the ‘Caps Lock’ light is not illuminated. c. If you really forget the password, do a hard reset. Router become hot a. This is not a malfunction, if you can keep your hand on the router’s ca...

142 4-3 Glossary Default Gateway (Router): Every non-router IP device needs to configure a default gateway’s IP address. When the device sends out an IP packet, if the destination is not on the same network, the device has to send the packet to its default gateway, which will then send it out toward...

143 A network mask is also a 32-bit binary pattern, and consists of consecutive leading 1’s followed by consecutive trailing 0’s, such as 11111111.11111111.11111111.00000000. Therefore sometimes a network mask can also be described simply as “x” number of leading 1’s. When both are represented side ...