Edelbrock 3562 - Manuals - manualsarea.com

Page 2 - MANIFOLD ASSEMBLY CONTENTS; hose; PERFORMER MULTI-POINT EFI; Description; SUGGESTED TOOLS AND MATERIALS FOR INSTALLATION

MANIFOLD ASSEMBLY CONTENTS Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 2 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 Qty. Description ❑ 1 Manifold assembly (see detail below) ❑ 1 Installation instructions ❑ 1 EPROM adapter circuit board (#3562 only) ❑ 1 Fuel injector wiring harness ❑ 1 Fue...

Page 3 - You must use; When filling out your information card, please print clearly.; SERVICE NUMBER; Typical ECM Label; AWHF

Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 3 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 IMPORTANT INSTRUCTIONSFor ordering your FREE Edelbrock computer chip. You must use an Edelbrock chip with the Performer Multi-Point EFI conversion ® You must change the computer chip in your stock com...

Page 4 - INSTALLATION INSTRUCTIONS; • APPLICATION; pico injectors. These are half the size of conventional style

Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 4 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 ® INSTALLATION INSTRUCTIONS for Performer Multi-Point EFI System for 7.4L TBI-Equipped Chevrolet/GMC Vehicles Catalog #3562 and #3564 for 1987-1990 Model Years Catalog #3563 and #3565 for 1991-1995 Mo...

Page 5 - INSTALLATION PROCEDURE; Coolant; Alternator

Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 5 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 INSTALLATION PROCEDURE 1. Disconnect negative battery cable. 2. Drain coolant. 3. Remove air cleaner assembly. 4. Label all lines, wires, and connections with masking tapebefore disassembly to aid in ...

Page 6 - DISTRIBUTOR REMOVAL; Remove plug wires from top of distributor cap. Make; note; of; MANIFOLD REMOVAL

Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 6 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 10. DISTRIBUTOR REMOVAL Remove plug wires from top of distributor cap. Make note of location of each wire. Remove distributor cap. Before removal ofdistributor, note the location of the distributor bo...

Page 7 - INTAKE PREPARATIONS; If any of the holes in the manifold are not used, plug them; MANIFOLD INSTALLATION; Some grinding on the bracket ears and on the rear of the; New EGR

Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 7 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 13. INTAKE PREPARATIONS With fuel lines out of the way, scrape remaining intake gasketsoff of cylinder heads and scrape both end seals clean. Withsurfaces clean, install intake gaskets to cylinder hea...

Page 8 - THERMOSTAT AND HOSES

Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 8 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 Tighten the manifold bolts following the tightening sequenceshown below. Torque to 25 ft. lbs. Install the distributor in the engine. Using your marks as a reference, snug down distributorclamp. NOTE:...

Page 9 - HEATER HOSE SUPPLY LINE; Place fuel rail with pressure; FUEL LINE CONNECTION; Be careful

Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 9 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 16. HEATER HOSE SUPPLY LINE For all years, the heater core supply will come from the right frontwater port on intake manifold. You will need to install the 1/2"NPT-to-3/4" hose fitting into ma...

Page 10 - FUEL RETURN LINE INSTALLATION; This may be left or right side, depending on year and; NOTE: Carefully flush out all debris after cutting lines!; From Regulator on; THROTTLE BRACKET; Usually the cut will be above the

Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 10 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 19. FUEL RETURN LINE INSTALLATION Install the 90° #6 pushlock fitting into the 10-foot length of hoseusing the pushlock fitting installation procedures describedpreviously. Tape off the open end of f...

Page 11 - ELECTRICAL CONNECTION

Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 11 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 Pull rubber grommet off of wires. Force silicone (oxygen sensor-safe) through these four holes, filling them with silicone. Install the grommet on air valve in groove to prevent dirt fromentering the...

Page 12 - Route hose and cut as necessary to; THROTTLE BODY CONVERSION; Install and; ACCESS FUEL TANK; On trucks with dual tank set-; Dual Tanks Require Kit #3580; Ground

Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 12 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 installed in manifold). Route hose and cut as necessary to prevent interference with linkage. Tighten both clamps andsecure with tie wrap as shown. Tie Wrap Brake Vacuum Hose From Booster to Supply P...

Page 13 - FUEL PUMP ASSEMBLY; Now disconnect; ALTERNATE PROCEDURE: LOWERING FUEL TANK; You may want to replace the fuel sock at this time with a

Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 13 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 Fuel Tank Disconnect two fuel lines, two hoses, and an electrical connectionwith a ground wire. There is a center fuel pump sending unitassembly lock ring holding assembly into tank. Using a hammeran...

Page 14 - Some; New Hose; Make electronic

Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 14 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 Note: The fuel line will be a very tight fit over the 3/8" tubing. It may be necessary to lube the tubing with some spray lubricantto ease hose installation. Slip the 5/16" clamp over the rub...

Page 15 - INITIAL START UP

Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 15 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 This installation uses a piggyback chip adapter. Push your newcomputer chip into the adapter, then install these two parts intoECM. There is an alignment lug so that they only fit one way. Becareful ...

Page 16 - Edelbrock Corporation • 2700 California St. • Torrance, CA 90503; Stroker motors are not supported.

Catalog #3562, 3563, 3564, 3565Rev. 3/06 Page 16 of 16 ©2006 Edelbrock Corporation Brochure #63-0047 Edelbrock Corporation • 2700 California St. • Torrance, CA 90503 EFI Tech-Line: (800) 416-8628, Option 3 • E-Mail: [email protected] ® BASIC TROUBLESHOOTING 1. Engine Combinations a. If you assem...