Eagle 2T - Manuals

5 Good and poor transducer locations. How low should you go? For most situations, you should install your Skimmer transducer sothat its centerline is level with the bottom of the boat hull. This willusually give you the best combination of smooth water flow and protec-tion from bangs and bumps. Alig...

6 There are two extremes you should avoid. Never let the edge of themounting bracket extend below the bottom of the hull. Never let thebottom – the face – of the transducer rise above the bottom of the hull. Shoot-thru-hull vs. Transom Mounting Typically, shoot-thru-hull installations give excellent...

7 B. Two-piece bracket: Locate the four plastic ratchets in the trans- ducer's hardware package. Press two ratchets into the sides of the plas-tic bracket and two on either side of the transducer as shown in the fol-lowing illustrations. Notice there are letters molded into each ratchet. Place the r...

8 2. Aligning the transducer on the transom. A. One-piece bracket: Slide the transducer between the two ratch- ets. Temporarily slide the bolt though the transducer assembly andhold it against the transom. Looking at the transducer from the side,check to see if it will adjust so that its face is par...

9 parallel with the ground. If you can, then go to step 3B. If it doesn't,repeat step 2B, but use a different alignment letter until you canplace the transducer on the transom correctly. Assemble transducer and bracket. 3. Assembling the transducer. A. One-piece bracket: Once you determine the corre...

10 Mark the center of each slot for the mounting screw pilot holes. Youwill drill one hole in the center of each slot. Drill the holes. For the one-piece bracket, use the #29 bit (for the #10screws). For the two-piece bracket, use the #20 bit (for the #12screws). Position transducer mount on transom...

11 Both bracket types: Attach the transducer to the transom. Slide thetransducer up or down until it's aligned properly with the bottom ofthe hull as shown in the preceding and following figures. Tighten thebracket's mounting screws, sealing them with the caulking compound. Adjust the transducer so ...

12 7. Make a test run to determine the results. If the bottom is lost at high speed, or if noise appears on the display, try sliding the trans-ducer bracket down. This puts the transducer deeper into the water,hopefully below the turbulence causing the noise. Don't allow thetransducer bracket to go ...

13 TRANSDUCER ORIENTATION AND FISH ARCHES If you do not get good fish arches on your display, it could be becausethe transducer is not parallel with the ground when the boat is at restin the water or at slow trolling speeds. Transducer angles and their effects on fish arches. If the arch slopes up –...

14 transducer installation can be made on hulls with flotation materials(such as plywood, balsa wood or foam) between layers of fiberglass ifthe material is removed from the chosen area. Epoxy the transducer to a solid portion of the hull. For example, some (but not all) manufacturers use a layer of...

15 cation that shot through the hull the best and follow the instructions onthe following pages for a shoot-thru-hull mounting. Shoot-thru-hull transducer locations for high speed or trolling speed operation. Shoot-thru-hull Installation 1. Make sure the area is clean, dry and free of oil or grease,...

16 Place the transducer into the epoxy, twisting and turning it to forceany air bubbles out from under the transducer face. The face of thetransducer should be parallel with the hull, with a minimum amountof epoxy between the hull and transducer. After the epoxy dries,route the cable to the sonar un...

17 Sonar unit with external temperature sensor. Transducer lacks a built- in temperature sensor. Sonar unit with external combination speed and temperature sensor. The transducer has no temperature sensor. Transducer with notemperature sensor ST-TU combination speed and temperature sensor TS-2Utempe...

19 Speed Sensor Installation If you wish to purchase an optional sensor for your unit, refer to theaccessory ordering information inside the back cover of this manual.The following instructions describe how to install the speed sensor. Recommended tools for this job include: drill, 5/8"drill bit...

20 If the base of the transom has a radius, fill the gap between the tran-som and the sensor with the caulking compound. This will help ensurea smooth water flow. Route the sensor's cable through or over the transom to the sonar unit.If you need to drill a hole in the transom to pass the connector t...

21 power buss. This will protect both the unit and the power cable in theevent of a short. It uses a 3-amp fuse. CAUTION: Do not use this product without a 3-amp fuse wired into thepower cable! Failure to use a 3-amp fuse will void your warranty. This unit has reverse polarity protection. No damage ...

22 mounting positions. Installation instructions for the in-dash and swivelmounting kits are supplied with the adapter kits. Bracket Installation Mount the unit in any convenient location, provided there is clearancewhen it’s tilted for the best viewing angle. Holes in the bracket’s baseallow wood s...

24 For a secure portable mount, attach the unit to the portable power pack's gimbal bracket using the supplied gimbal knobs and washers as shown above. Installing the Batteries Release the latch on the front of the battery case. Open the compart-ment and install either an optional rechargeable batte...

25 Install batteries in power case battery adapter. In cold weather the efficiency of dry cell batteries drops with the tem-perature. We find it a good idea to have the sonar unit good and warmalong with the batteries before we leave home. If the batteries do lose a charge, you can sometimes restore...

26 Portable transducer assembly: rear view (left) and side view (right.) Clean the chosen area of the hull before attaching the suction cup. Lo-cate the transducer on the hull as shown in the following figure. Don'tallow the bracket to extend below the hull, because water pressureagainst it can caus...

27 Operation KEYBOARD BASICS The unit sounds a tone when you press any key. This tells you the unithas accepted a command. Numbers in the photo correspond to key ex-planations below: Eagle FishEasy 2 Sonar, front view, showing screen and keyboard. 1. PWR/CLEAR (power and clear) This key appears in t...

28 tively.) Most of the time, the instructions require you to press eithermenu key, so the text simply uses the word MENU . Usually, when we say MENU , you can simply press the MENU UP key for consistency. This sonar unit has many features that are accessed with the menukeys. The MENU UP key moves u...

29 UP ARROW . If you don’t press a key, the menu will disappear after a few seconds. If you don't want to wait, press PWR to clear the menus from the screen. When the sonar unit is first turned on and the backlight menu disap-pears, the display screen shows the Full Chart Page, or mode. The FishI.D....

30 SCREEN DISPLAY MODES or PAGES The FishEasy 2 series has three screen display modes, or "Pages:" FullChart page, Split Chart page and Large Digital page. The SeaFinder240DF also has a Dual Frequency page. The Page menu lets you select among the display modes, or pages. Left, FishEasy 2 ser...

31 If an optional speed or temperature sensor is connected, digital displays forspeed and/or temperature will also be shown. SPLIT CHART This shows the normal view of the underwater world from the surface tothe bottom on the right side of the screen. The left side shows an enlargedor "zoomed"...

32 You can adjust the sensitivity in each window. To change the 200 kHzwindow's sensitivity, press MENU until the S ENSE 200 K menu appears. Press UP ARROW to increase the sensitivity, DOWN ARROW to decrease it. When it's set at the desired level, press PWR to clear the menu. Change the 50 kHz windo...

33 RANGE When turned on for the first time, the unit automatically adjusts thedepth range according to water conditions. It always keeps the bottomdisplayed in the lower portion of the screen. You can over-ride theautomatic range control and manually select a range. To do this, press MENU until the ...

34 To zoom the display, first press the MENU key until the Z OOM menu ap- pears. Use the arrow keys to select either 2X or 4X zoom, then press PWR to clear the menu. When the display is in Zoom mode, the screen will show a zoom indica-tor box at the top right corner of the screen. This is a reminder...

38 At left, Grayline menu screen. Center, little Grayline indicates a soft bottom, probably sand or mud. At right, the wider Grayline indicates a harder, rocky bottom. FISH I.D.  The Fish I.D.  feature identifies targets that meet certain conditions as fish. The microcomputer analyses all echoes a...

39 Fish I.D. is an easier way for a sonar novice to recognize a fishy signalreturn when he sees it. However, locating fish by symbol only has some limitations. Your sonar unit's microcomputer is sophisticated, but it can be fooled.It can't distinguish between fish and other suspended objects such as...

40 Fish ID menu and symbol with FishTrack on. The fish is 44 feet deep. FISHREVEAL  When displaying actual sonar returns, the FishReveal  feature helps show fish targets hidden by surface clutter, thermoclines, weed bedsand other cover with 10 levels of gray tones. Normal operation (with FishRevea...

41 There are two FishReveal modes: standard and inverted. In standardmode, the weakest echoes are white and the strongest echoes are black.Echoes in between vary in gray in proportion to their signal strength. In Inverted FishReveal mode, the weakest echoes are black and thestrongest echoes are whit...

42 If you are at anchor, ice fishing or fishing from a dock, experiment witha chart speed of 20 percent. If you are drifting slowly, try a chart speedof 40 percent. When you are stationary and a fish swims through thesonar signal cone, the image appears on the screen as a long line in-stead of a fis...

43 ASP is an effective tool in combating noise. In sonar terms, noise is anyundesired signal. It is caused by electrical and mechanical sources suchas bilge pumps, engine ignition systems and wiring, air bubbles passingover the face of the transducer, even vibration from the engine. In allcases, noi...

45 Press UP ARROW to increase the shallow alarm's depth setting or press DOWN ARROW to decrease it. The number in the shallow alarm’s menu box shows the current shallow alarm setting. When the number reachesthe desired setting, press PWR to clear the menu. When the bottom depth goes shallower than t...

46 SYSTEM SETUP To customize the display, press MENU DOWN until the S YSTEM S ETUP menu appears, then press UP ARROW . The display contrast, units of measure, temperature, and system information screens are all underthis menu. The Contrast menu appears first. Press the MENU UP or MENU DOWN keys to c...

47 ous times of the day. The default setting is 50 percent. To adjust the contrast, press MENU DOWN until the S YSTEM menu ap- pears, press UP ARROW , and the C ONTRAST menu appears. To decrease screen contrast, press the DOWN ARROW key. Press the UP ARROW key to increase screen contrast. The bar gr...

48 TEMPERATURE UNITS OF MEASURE This unit can show the temperature (if a temperature sensor is attached)in degrees Fahrenheit or Celsius. To change the unit of measure, press MENU DOWN until the S YSTEM menu appears. Press UP ARROW , then press MENU until the T EMPERATURE menu appears. Use the arrow...

49 RESET DISTANCE LOG You can reset the distance log to zero with this command. Press MENU DOWN until S YSTEM appears, then press UP ARROW . Press MENU until the R ESET L OG menu appears. Press UP ARROW and the log returns to zero. Press PWR to clear the menu. Reset Log menu. PRESET UNIT (reset all ...

50 SYSTEM INFO To show the operating software system information, press MENU DOWN until the S YSTEM menu appears, then press UP ARROW . Press MENU DOWN until the S YSTEM I NFO screen appears. Press PWR to clear the screen. System Info screen. SIMULATOR This unit has a built-in simulator that shows a...

51 NOTE: If you turn on your unit before attaching a transducer, it may entera demo mode. The words "demo mode" flash on the bottom of thescreen and a sonar chart plays much like the simulator. Unlike thesimulator, the demo mode is for demonstration only, and will auto-matically stop as soon...

53 The default frequency is 200 kHz, which is best for use in shallow water(about 300 feet or less). This frequency is the best choice for about 80percent of the fresh and salt water sport fishing applications. When youget into very deep salt water, 300 to 500 feet or deeper, the 50 kHz fre-quency i...

54 Menus for changing digital number size. SCALES The depth scale between the upper and lower limit on the right side ofthe screen can be turned on or off. The default is on. Scales menu, with scale on (left) and off (right). With the scale off, only the upper and lower limits (zero and 60 in this c...

55 Troubleshooting If your unit is not working, or if you need technical help, please use thefollowing troubleshooting section before contacting the factory customerservice department. It may save you the trouble of returning your unitfor repair. For contact information, refer to the last page, just...

57 NOISE A major cause of sonar problems is electrical noise. This usually ap-pears on the sonar's display as random patterns of dots or lines. In se-vere cases, it can completely cover the screen with black dots, or causethe unit to operate erratically, or not at all. To eliminate or minimize the e...

61 EAGLE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to EAGLE ELECTRONICS, a division of LEI, the manufacturerof this product. "You" or "your" refers to the first person who purchases this product as aconsumer item for personal, family, or h...

62 How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert serviceand genuine Eagle replacement parts. If you're in the United Statesand you have technical, return or repair questions, please contact theFactory Customer Service Department. Before any produc...

Accessory Ordering Informationfor all countries To order Eagle accessories such as power cables or transducers,please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumerelectronics should be able to assist...

Visit our web site: www.eaglesonar.com Eagle Pub. 988-0143-641 © Copyright 2002 All Rights Reserved Printed in USA 092402 Eagle Electronics 