Eagle 640C - Manual

1 Section 1: Read Me First! How this manual can get you out on the road, fast! Welcome to the exciting world of digital GPS! We know you're anxiousto begin navigating, but we have a favor to ask. Before you grab theIntelliMap ® 640c and begin installing it, please give us a moment or two to explain ...

2 After you've learned the basics (or if you already have some GPS expe-rience), you may want to try out some of the IntelliMap 640c's manyadvanced navigation features. That brings us to Section 4, Advanced GPS Operations . This section contains the rest of the unit's GPS com- mand functions, organi...

3 Case size: ......................... 5.4" H x 6.9" W x 3.4" D (13.8 x 17.6 x 8.6 cm); sealed and waterproof; suitable forsaltwater use. MMC slots: ...................... One, with waterproof door (SD card compatible). Recording: ........................ MMC & SD cards for recording...

4 NOTE: The above memory capacities refer only to the IntelliMap 640c's on-board memory. The amount of GPS data you can record and save forrecall later is limited only by the number and size of MMC cards youhave. NOTICE! The storage temperature range for your IntelliMap 640c is from -4degrees to +16...

6 Introduction to GPS and WAAS Well, now you know the basics of how the unit does its work. You mightbe ready to jump ahead to Section 2, Installation & Accessories, on page 11, so you can mount your IntelliMap 640c and plug in the power. Oryou might want to see how our text formatting makes the...

8 only a tool. Always have another method of navigation available, suchas a map or chart and a compass. Also remember that this unit will always show navigation informationin the shortest line from your present position to a waypoint, regardlessof terrain! It only calculates position, it can’t know ...

11 Section 2: Installation & Accessories Preparations You can install the GPS system in some other order if you prefer, butwe recommend this installation sequence: Caution: You should read over this entire installation section before drill-ing any holes in your vehicle or vessel! 1. Determine th...

12 You need to select an antenna installation location that has a clear, un-obstructed view of the sky. After the module is installed, route the cableto the unit, plug it in the center socket on the back and your system isready to use. See the module's instruction sheet, publication part num-ber 988...

13 For example, if you have to extend the power cable to the battery orpower buss, attach one end of the fuse holder directly to the battery orpower buss. This will protect both the unit and the power cable in theevent of a short. It uses a 3-amp fuse. Power connections for the IntelliMap 640c GPS u...

14 Cable connections. NMEA Cable Connections NMEA is a standard communications format for marine electronicequipment. For example, an autopilot can connect to the NMEA inter-face on the IntelliMap 640c and receive positioning information. TheIntelliMap 640c can exchange information with any device t...

15 However, a communications cable is not available for the unit at this time.If you need to create a NMEA 0183 connection consult customer service.Service contact information can be found in the back of this manual. NMEA Wiring To exchange NMEA data, the IntelliMap 640c has one NMEA 0183 ver-sion 2...

16 Optional R-A-M mounting system. Bracket Installation Mount the IntelliMap 640c in any convenient location, provided there isclearance behind the unit when it's tilted for the best viewing angle.You should also make sure there is enough room behind the IntelliMap640c to attach the power and GPS an...

17 Front view (left) and side view (right) showing dimensions of the IntelliMap 640c when mounted on gimbal bracket. After drilling the hole, pass the antenna connector up through the hole from under the dash. Pass the power cable's bare-wire end down though the hole from the top. If you wish, you c...

18 In-dash mounting template for the IntelliMap 640c, showing dimensions. NOTE: The figure above is not printed to scale. a scaled template (FM-5 In-Dash Adapter Kit instructions) is available for free download from our web site, www.eaglegps.com. Portable Installation Like many Eagle products, the ...

19 Installing batteries in a typical portal power pack. MMC or SD Card Memory Card Installation Your IntelliMap 640c uses a MultiMedia Card to store information,such as custom maps, waypoints, trails and other GPS data. NOTE: Throughout this manual, we will use the term MMC, but just re-member that ...

20 Memory card compartment with a 16 MB MMC card installed. To remove an MMC 1. Open the card compartment door by unscrewing the thumb screw.The screw should only be finger tight. If it was over-tightened, use athumbnail, a coin or a screwdriver to open the door. 2. Just press a finger against the l...

21 MapCreate™ 6 CD-ROM (left) and MMC card reader for USB ports on the right. Now that you have your IntelliMap 640c installed, move on to Section3, Basic GPS Operations . There, we'll present a series of step-by-step tutorials to teach you the basics of GPS navigation.

23 Section 3: Basic GPS Operations This section addresses the unit's most basic GPS operations. The tuto- rials presented in Sec. 3 follow a chronological order. Sec. 4, Advanced GPS Operations , will discuss other more advanced functions and utili- ties. Material in Sec. 4 is arranged in alphabetic...

24 3. MENU – Press this key to show the menus and submenus, which allow you to select a command or adjust a feature. This also accessessearch functions for streets, intersections, addresses and highway exits. 4. ARROW KEYS – These keys are used to navigate through the menus, make menu selections and...

26 Pages The unit has three Page displays that represent the three major oper-ating modes. They are the Satellite Status Page, the Navigation Pageand Map Page. They are accessed by pressing the PAGES key, then us- ing → or ← to select a Page. Exit the Pages Menu by pressing EXIT . Pages Menu showing...

28 The Satellite Status Page has its own menu, which is used for settingvarious options. Options and setup are discussed in Sec. 5. To accessthe Satellite Status Page Menu, from the Status Page, press MENU . Navigation Page This screen has a compass rose that not only shows your direction oftravel, ...

29 Speed is the velocity you are making over the ground. If you prefer, youcan customize the Speed data box to display Closing Speed instead.Closing Speed is also known as velocity made good. It's the speed thatyou're making toward the waypoint. For instructions, see the Custom-ize Page Displays ent...

31 Map Page opening screen (left). Map zoomed to 100 miles (center). Map zoomed to 10 miles (right). Over Zoomed, listed at the top of the map screen (right) means you have reached the detail limits in an area cov- ered only by the basic background map. Zooming in any closer will reveal no more map ...

33 When the map is zoomed out far enough, most POIs appear as squaredots (left). As you zoom in closer, the symbols become readable icons. In the 0.2-mile zoom example (right), the cursor has selected the Cupps Café POI, which triggers a pop-up box with the POI name Tip: In some urban areas, busines...

34 Digital Data map page option. In pages that have two major windows you can toggle back and forthbetween the two windows by pressing PAGES | PAGES . This allows you to change the active map. Only when a map is active are you able tomake adjustments to it. Pages Menu (left) with Two Map option sele...

35 the window widths. Press an arrow key parallel to the centerline toswitch between horizontal and vertical layout. On the Map with Sonar page, you can only change size, not switch lay-out. It is always two vertical windows. Press EXIT to clear the four flashing arrows. (From left to right) Fig. 1....

36 Basic GPS Quick Reference Start outdoors, with a clear view of the open sky. As you practice, trynavigating to a location at least a few blocks away. While you're learning,navigation in too small an area will constantly trigger arrival alarms. 1. Connect the unit to electric power and the antenna...

37 Find Your Current Position Finding your current position is as simple as turning the unit on. Un-der clear sky conditions, the unit automatically searches for satellitesand calculates its position in approximately one minute or less. NOTE: "Clear sky" means open sky, unobstructed by terra...

38 The selected wreck (the Empress) to the southeast is 40 miles away. Selecting Any Map Item with the Cursor 1. Use the zoom keys and the arrow keys to move around the map andfind the item you wish to select. 2. Use the arrow keys and center the cursor cross-hair on the desired ob-ject. On most ite...

39 After the unit has acquired a position: 1. Press WPT | ↓ to POI-R ESTAURANTS . 2. You could search the entire restaurant category, but in this examplewe will narrow our search. Press → to F AST F OOD C HAINS | ENT | ENT . 3. The unit says it is calculating, then a list of restaurants appears,with...

40 5. The POI information screen appears. (This is how you can use thisunit as a business phone directory!) If you wanted to navigate there,you could press Enter, since the Go To waypoint command is high-lighted. But we just want to see it on the map, so press → to F IND O N M AP | ENT . 6. The unit...

42 Sequence for setting a waypoint. Step 1: while traveling, press WPT to call up Find Waypoint screen (seen in Step 2) and set a point. Step 3: a message says the waypoint has been saved. Step 4: vehicle continues on its way; number waypoint symbol is visible on map. Create Waypoint on Map 1. Use t...

43 3. Press → to L ATITUDE | ENT . Enter the latitude by pressing ↑ or ↓ to change the first character, then press → to the next character and re- peat until the latitude is correct. Press ENT . 4. Press ↓ to L ONGITUDE | ENT . Enter the longitude by pressing ↑ or ↓ to change the first character, th...

44 Set Man Overboard (MOB) Waypoint One of boating's most terrifying events is having a friend or familymember fall overboard. This unit has a man overboard feature thatshows navigation data to the location where the feature was activated.To activate it, press the ZOUT and ZIN keys at the same time....

45 Navigate to Cursor Position on Map The G O T O C URSOR command navigates to the current cursor position on the map. It is a quick way to navigate to anything you can see on themap display. 1. Use the cursor with the zoom in and zoom out keys to move aroundthe map until you find a location you wan...

46 The 60-mile zoom figure (left) shows the red course line connecting the current position to the destination. The Navigation Page (right) will also show navigation information. To stop navigating to the cursor, use the Cancel Navigation command.Press MENU | MENU | ↓ to C ANCEL N AVIGATION | ENT | ...

47 until the length reaches the maximum trail point setting (default is2,000, but the unit can record trails 9,999 points long). When the pointlimit is reached, the unit begins recording the trail over itself. With the default auto setting, this unit creates a trail by placing a dot(trail point) on ...

48 Tip: Another quick way to stop recording one trail and begin a new oneis to use the New Trail command. Press MENU | MENU | ↓ to M Y T RAILS | ENT | ENT . Caution: You also have the option of completely turning off trail record-ing, under the trail Options command. However, if the UpdateActive Tra...

50 Navigate a trail menu sequence: Fig. 1, My Trails command. Fig. 2, Trails Menu. Fig. 3, Edit Trail Menu. Fig. 4, Edit Route Menu with Navigate Route command highlighted for Trail 2. A trail is always con- verted to a route when you navigate the trail. On the Map Page, the trail you are navigating...

51 Navigate trail: Driver (left) is heading southeast straight toward trail point 3. Driver (right) has reached point 3 and has turned southwest to follow the trail. Navigate trail, navigation page (compass rose) views: Driver is heading north straight toward trail point 3 (left). Bearing arrow show...

52 NOTE: If you are already located at or near the end of your trail, the arri-val alarm will go off as soon as you hit Enter. Just press EXIT to clear the alarm and proceed. 5. Now, begin moving and allow the unit to guide you. 6. When you reach your destination, be sure to cancel your navigation.P...

53 Insert the MMC into your unit. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to T RANSFER M Y D ATA | ENT . 2. The Transfer My Data menu includes a message which tells you if anMMC is present or not. If no MMC is present, you must first insert acard into the unit in order to activate the Load...

54 These figures show the menu sequence for loading a GPS Data File from an MMC into the unit's memory. Cancel Navigation You can turn off any of the navigation commands after you reach yourdestination or at any other time by using the Cancel Navigation com-mand. Press MENU | MENU | ↓ to C ANCEL N A...

55 Section 4: Advanced GPS Operations Find Distance From Current Position To Another Location 1. While on the Map Page press MENU | ↓ to F IND D ISTANCE | ENT . 2. Center your cursor over the position you want to find the distance to.A rubber band line appears, connecting your current position to th...

56 Icons Icons are graphic symbols used to mark some location, personal point ofinterest or event. They can be placed on the map screen, saved and re-called later for navigation purposes. These are sometimes referred to asevent marker icons. This unit has 42 different symbols you can pickfrom when c...

57 Delete an Icon You can delete all the icons at one time, you can delete all icons repre-sented by a particular symbol, or you can use the cursor to delete a se-lected icon from the map. Delete icons menu. 1. Press MENU | ↓ to D ELETE M Y I CONS | ENT . 2. Press ↓ to D ELETE A LL I CONS , D ELETE ...

58 course of travel connecting waypoint to waypoint. The course from onewaypoint to the next is a leg. Routes are composed of one or more legs.The legs of all GPS routes are based on straight lines between way-points. A route allows you to navigate through several waypoints with-out having to reprog...

59 2. Press ↑ to N EW R OUTE , then press ENT . To add to an existing route, press ↓ or ↑ to route name | ENT . Edit Route menu (left). Edit Route Waypoints menu (right) with Add From Map command selected. 3. Press ↓ to E ND OF R OUTE | ENT | ↓ to A DD F ROM M AP | ENT . The Map Page appears with th...

60 Route creation sequence, continued: Fig. 4. Point (3) set at channel mouth. Fig. 5. Waypoint (4) set further south along the beach, at a recognizable landmark. The route will end with waypoint 5 at an oil platform. Fig. 6. Press EXIT to save the route and you return to this screen. 6. Move the cu...

61 Edit a Route Name 1. From the N AVIGATION P AGE , press MENU | ENT or from the M AP P AGE press MENU | MENU | ↓ to R OUTE P LANNING | ENT . 2. Press ↓ to route name | ENT | → to E DIT R OUTE N AME | ENT . 3. Press ↑ or ↓ to change the first character, then press → to move the cursor to the next c...

62 Navigate a Route 1. From the N AVIGATION P AGE , press MENU | ENT or from the M AP P AGE , press MENU | MENU | ↓ to R OUTE P LANNING | ENT . Route Planning command (left) on Main Menu. Routes menu (center) with Edit Route menu at right. Navigate Route command is selected. 2. Press ↓ to select sav...

63 Edit Route screen showing Route 1 with waypoints set to normal navigation (left). Reverse command has been executed (center) revers- ing the order of waypoints on the route. Pressing Navigate (right) will allow you to navigate the route from the end to the beginning. Trails Delete a Trail This is...

64 Trail selected with map cursor (left). The box at the bottom of the screen shows distance and bearing from current position to the se- lected point on the trail. The Edit Trail menu (right). Edit a Trail Color To edit a trail color press MENU | MENU | ↓ to M Y T RAILS | ENT | ↓ to trail name | EN...

65 Utilities Utilities are useful tools for traveling or for outdoor activities. Alarm Clock To get to the alarm clock menu press MENU | MENU | ↓ to T IMERS | ENT | ↓ to A LARM C LOCK | ENT . Sun/Moon Rise & Set Calculator To get to the Sun/Moon menu press MENU | MENU | ↓ to S UN /M OON C ALCULA...

69 Section 5: System & GPS Setup Options Alarms This unit has three GPS alarms: Arrival Alarm, Off Course Alarm andAnchor Alarm — the only one of the three set to Off by default. You can set an arrival alarm to flash a warning message and sound atone when you cross a preset distance from a waypo...

70 repeat until you are satisfied with the distance setting. If you want toenable the other alarms, repeat steps 2 and 3. 4. Press EXIT repeatedly to get back to the main page display. IMPORTANT ALARM NOTES: Anchor Alarm - The anchor alarm may be triggered even whenyou're sitting still. This typical...

71 Menus for changing Com Port settings. For connectors and wiring information for another device, see page 15.For assistance in configuring the unit to communicate with anotherdevice, consult the factory. Customer service phone numbers are in theback of this manual. Also see the entry below for Con...

72 • VLW transmits the distance traveled through water as meas-ured by the paddle wheel. • VHW transmits the water speed as measured by the paddlewheel. 4. When the desired prefixes are checked or unchecked, press EXIT | EXIT | EXIT | EXIT to return to the previous page. Coordinate System Selection ...

73 The Military Grid Reference System (MGRS) uses two grid letteringschemes, which are referred to as standard and standard + 10 MGRSon this unit. Your position and datum in use determines which one touse. If you use standard and your position is off significantly try thealternate. NOTE: When the po...

74 To configure a map fix: To use this format, you need to follow these steps in order. Take a mapof the area and determine a reference latitude/longitude. NOTE: In order for this system to work, the latitude/longitude lines mustbe parallel with the edge of the map. USGS maps are parallel, oth-ers m...

75 command S ET A S O RIGIN selected. Press ENT and the unit returns to the Configure Map Fix menu. Finally, press EXIT to close this menu. Now press ↑ to C OORD S YSTEM | ENT , select M AP F IX from the list and press ENT . Press EXIT repeatedly to get back to the main page display where all positi...

76 GPS Simulator The GPS simulator simulates real world navigation. It is a great way topractice using your unit. You can set the starting location by enteringlatitude/longitude or from a stored waypoint, map place or POI location.You can steer the position arrow and change speed on the map by using...

77 mate T RACK (shown in compass degrees) that will point you toward the start of the trail/route. 2. Set S PEED to zero. Select S TEER WITH A RROWS command and press ENT , which turns on the simulator and returns you to the Map Page. 3. Begin navigating along the trail/route. (If you are close enou...

78 to the destination waypoint. As you travel toward the destination, theunit automatically zooms in — one zoom range at a time — keepingyour current position and the destination on the screen. To turn this feature on from the M AP P AGE , press MENU | ↓ to A UTO Z OOM | ENT | EXIT . Repeat these st...

79 Fill Water With White From the Map Page, press MENU | ↓ to M AP D ATA | ENT . Press ↓ to F ILL W ATER W ITH W HITE . With the option highlighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT | EXIT to return to the page display. Map Overlays (Rang...

80 3. To return to the main page display, press EXIT | EXIT . A list of the datums used by this unit is in the back of this manual. GPS Setup Menu (left) Map Datum Menu at right. Map Detail Category Drawn This menu determines what mapping features are shown on the screen.This includes, waypoints, tr...

81 Map Orientation By default, this receiver shows the map with north always at the top ofthe screen. This is the way most maps and charts are printed on paper. Map orientation shown in north up (left) and track up (right). This is fine if you are always traveling north. What you see to your leftand...

82 Map Menu (left). Map Orientation menu with the North Up selected (right). NOTE: In North Up and Course Up, the present position arrow appears inthe center of the map page. In Track Up, the position arrow appearscentered in the lower third of the page. NauticPath  USA Marine Charts Your unit can ...

85 NauticPath chart showing Tidal Current Station icon selected by cur- sor (left). Icon animates automatically at .08-mile zoom range (right). Current Information screen. The Tidal Current Information screen displays daily tidal current datafor this station on this date at the present time. The gra...

86 To select another date: 1. Use ← → to highlight month, day or year, then press ENT . 2. Use ↑ ↓ to select the desired month, day or year and press ENT . To clear the information screen, press EXIT . Tide Information NauticPath charts contain Tidal Information,represented at large zoom ranges by a...

87 Tide Information screen. The Tide Information screen displays daily tidal data for this station onthis date at the present time. The graph at the top of the screen is anapproximate view of the tidal range pattern for the day, from midnight(MN) to noon (NN) to midnight (MN). The dotted line across...

88 2. From the Map Page, press MENU | ↓ to M AP D ATA | ENT | ↓ to M AP C HOICE | ENT . Select the Map Name , then press ENT | EXIT | EXIT . South Chesapeake Navionics selected from Map Choice menu (right). WARNING: You should never format the MMC containing yourNavionics chart. Formatting the MMC w...

89 Overlay Data, with "Navigation," "Trip Calculator" and "Time" categories expanded. To overlay information on your screen: 1. While on the Navigation Page or a Map Page, press MENU | ↓ to O VERLAY D ATA | ENT . 2. You'll see a list of the overlay data currently shown, if an...

90 From Overlay Data Shown (left) press ENT to see Data Viewer (center). Select a category and press ENT ; then select information to float on screen and press ENT (right). To remove overlaid data: 1. While on the Page that shows the item or items you want to remove,press MENU | ↓ to O VERLAY D ATA ...

91 1. From one of the Map Pages, press MENU | ↓ to O VERLAY D ATA | ENT . 2. You'll see a list of the overlay data currently displayed. Select theitem you want to move and press ENT | → to M OVE | ENT . 3. The data begins to flash on your screen. Use any combination of → , ← , ↑ and ↓ to move the da...

92 Reset Options To reset all features to their factory defaults: 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to R ESET O PTIONS | ENT | ← to Y ES | ENT . NOTE: Reset Options does not erase any waypoints, routes, icons or plot trails. System Menu with Reset Options command selected. Require...

93 Screen Contrast and Brightness To access the Screen menu, press MENU | MENU | ENT . The C ONTRAST slider bar is already selected. Press ← → to adjust the contrast. To adjust the display's brightness: Press ↓ to B RIGHTNESS . Use ← → to adjust the brightness of the display. Screen Command (left). ...

94 To set the Month: Press ↓ to M ONTH | ENT . Use ↑ ↓ to select the month and press ENT . To set the Day: Press ↓ → to D AY | ENT . Press ↑ ↓ to select the day and press ENT . To set the Year: Press ↓ → to Y EAR | ENT . Press ↑ ↓ to select the year and press ENT . To set Time Format: Press ↓ to T I...

95 Main Menu (left) with Software Information command selected. The Software Information screen is shown at right. 1. Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ↓ to S OFTWARE I NFORMATION | ENT . 2. Read the information displayed on the screen. 3. To return to the last page displayed, press EX...

96 To set Alarm Sounds: Press ↓ to A LARM S OUNDS . With the option high- lighted, press ENT to check it (turn on) and uncheck it (turn off.) After the option is set, press EXIT | EXIT to return to the page display. To set Alarm Volume: Press ↓ to V OLUME . Press → or ← to move the bar. The left end...

99 Transparency set to 0 percent (left), 50 percent (center) and 100 percent (right). Transparency Use the transparency menu to adjust the transparency of menu win-dows. A high transparency setting allows you to continue monitoringthe screen's display while working with a menu. A low transparencyusu...

100 Units of Measure This menu sets the speed, distance, depth, temperature and headingunits. To change the units: Press MENU | MENU | ↓ to S YSTEM S ETUP | ENT | ENT . To set Units of Measure: Select a category you would like to change. Highlight the desired unit of measure option under the categor...

102 In search results, the distance and bearing to the selected item willbe calculated from the current position. In the case of a cursorsearch, the search results show distance and bearing from the cur-sor, but an individual waypoint's information screen shows distanceand bearing from the current (...

103 is correct, then press ENT | ENT . B. Jump down to the lower selection list by pressing ENT , then press ↓ or ↑ to select a city name from the list, then press ENT . The city name you selected is now in the city field. NOTE: We recommend that you do not enter a city name unless the list you are ...

104 Find Any Item Selected by Map Cursor On the Map Page, with a POI or map feature selected by the cursorpress WPT. To return to the previous page, press EXIT . Map Page (left) showing location of the address on the map, high- lighted by cursor. The address (right) is a business in the POI data- ba...

105 2. First, select a highway name by pressing ENT , which calls up the Find By Name menu. There are two highway search options. First, youcan spell out the highway name in the top selection box. Press ↑ or ↓ to change the first letter, then press → to move the cursor to the next letter and repeat ...

106 4. In the Exit Information screen you have two choices. Press ENT to navigate or "go to" the exit or press → | ENT to find the exit on the map. "Go To Exit" option (left) and "Find On Map" option at right. Tip: You can also look up additional information on the Exit Servi...

107 Find Waypoint menu with Lodging POI category selected. 2. To search by nearest POI select NEAREST and press ENT . The Find BY menu will show a "calculating" screen, then a list of the nearest POI'swill appear. Press ↓ or ↑ to the selected POI and press ENT to call up the POI's Waypoint I...

108 A list of Find by Nearest (left) and Waypoint Information menu at right. 4. When the POI's Waypoint Information screen is displayed, you canchoose "Go To Waypoint" or "Find On Map" by pressing ↓ or ↑ | ENT . Find Streets or Intersections Find a Street 1. From the Map Page, press ...

109 to change the first letter, then press → to move the cursor to the next letter and repeat until the name is correct, then press ENT | ENT . Or you can jump down to the lower box and pick a street from the selection list. Press ENT , then press ↓ or ↑ to select a street from the list and press EN...

110 If you want to navigate to the found street at the cursor location, justpress MENU | ENT | EXIT . Find an Intersection You must enter one street in the First Street dialog box and enter thenext street in the Second Street dialog box. 1. From the Map Page, press MENU | ↓ to F IND S TREETS | ENT a...

111 Find Intersection command highlighted on the left and the Find First Street command highlighted at right. 6. To search for the intersection of the two streets, press ↓ to F IND I NTERSECTION | ENT . A message appears asking you to wait while the unit finds the intersection. When the Intersection...

112 Find Waypoints 1. Press WPT | ↑ to M Y W AYPOINTS | ENT . 2. When searching for the nearest waypoint, press ENT . If searching for the waypoint by name , highlight N AME then ENT . (To search by name, jump to step 5.) Find By Nearest command (left). Find by Name command (center). List of the nea...

113 Find By Name menu (left). Waypoint Information screen (center). The cursor crosshairs are centered on the desired waypoint (right). A. To navigate to the waypoint, press ENT . The Go To Waypoint command is already highlighted. The unit will show navigation in-formation to the waypoint. B. To fin...

115 Section 7: Supplemental Material Datums Used by This Unit WGS 1984Default AdindanMean for Ethiopia,Sudan AdindanBurkina Faso AdindanCameroon AdindanEthiopia AdindanMali AdindanSenegal AdindanSudan AfgooyeSomalia Ain el Abd 1970Bahrain Ain el Abd 1970Saudi Arabia Anna 1 Astro 1965Cocos Islands An...

119 FCC Compliance This device complies with Part 15 of the U.S. Federal Communi-cations Commission (FCC) Rules. Operation is subject to the fol-lowing two conditions: (1) this device may not cause harmful in-terference, and (2) this device must accept any interference re-ceived, including interfere...

126 DATABASES LIMITED WARRANTY "We", "our", or "us" refers to Eagle Electronics, a division of LEI, the manufac-turer of this product. "You" or "your" refers to the first person who purchasesthe product as a consumer item for personal, family, or household use...

127 EAGLE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to EAGLE ELECTRONICS, a division of LEI, the manufac-turer of this product. "You" or "your" refers to the first person who purchases this productas a consumer item for personal, family, o...

128 How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert serviceand genuine Eagle replacement parts. If you're in the United Statesand you have technical, return or repair questions, please contact theFactory Customer Service Department. Before any produ...

Accessory Ordering Informationfor all countries To order Eagle accessories such as power cables or MMC cards,please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should beable to assist y...

Visit our web site: www.eaglesonar.com Eagle Pub. 988-0143-881 Copyright © 2005 All Rights Reserved Printed in USA 121905 LEI-Eagle 