Eagle 240 - Manuals

2 Display: ............................ High-contrast Film SuperTwist LCD. Diago- nal viewing area: 3.5" (8.9 cm). Resolution: ...................... 240 pixels (vert.) x 160 pixels (horiz.) resolu- tion; 38,400 total pixels Backlighting: .................. Amber LED backlit screen and keypad fo...

3 Auto bottom track: ........ Yes. Zoom bottom track: ....... Yes. Split-screen zoom: ......... Yes. Surface water temp: ..... Yes, built into transducer. Optional external temperature sensor or combo speed/temp sensor available. Speed/distance log: ....... Yes, with optional speed sensor. This manu...

5 Transducer Installation Preparations The following shows the recommended sequence for installing the transducer: CAUTION: You should read over this entire installation section before drill-ing any holes in your vehicle or vessel! 1. Determine the approximate location for the sonar unit, so you can...

6 trolling motor mount uses a one-piece plastic bracket with an adjust- able strap. These are all "kick-up" mounting brackets. They help prevent damage if the transducer strikes an object while the boat is moving. If the trans- ducer does "kick-up," the bracket can easily be pushed b...

7 Single-frequency trolling motor installations Tools: two adjustable wrenches, flat-head screwdriver. Supplies: plastic cable ties. Shoot-through hull installations Tools: these will vary depending on your hull's composition. Consult your boat dealer or manufacturer. Supplies: 100 grit sandpaper, s...

8 Left, vee pad hull; right, vee hull. A pod style transducer is shown here, but the principle is the same for Skimmers inside a hull. 4. If the transducer is mounted on the transom, make sure it doesn't interfere with the trailer or hauling of the boat. Also, don't mount it closer than approximatel...

9 How low should you go? For most situations, you should install your Skimmer transducer so that its centerline is level with the bottom of the boat hull. This will usually give you the best combination of smooth water flow and protec- tion from bangs and bumps. Align transducer centerline with hull...

10 tion (often called simply "thru-hull"). In that case, a hole is cut in the hull and a specially designed transducer is mounted through the hull with a threaded shaft and nut. This puts the transducer in direct con- tact with the water. Typically, shoot-thru-hull installations give excelle...

11 the metal bracket. This position sets the transducer's coarse angle ad-justment for a 14 ° transom. Most outboard and stern-drive transoms have a 14 ° angle. Align plastic ratchets in bracket. 2. Aligning the transducer on the transom. Slide the transducer between the two ratchets. Temporarily sl...

12 Insert bolt and check transducer position on transom. 3. Assembling the transducer. Once you determine the correct posi- tion for the ratchets, assemble the transducer as shown in the following figure. Don't tighten the lock nut at this time. Assemble transducer and bracket. Ratchets Nut Metal wa...

13 4. Drilling mounting holes. Hold the transducer and bracket assem- bly against the transom. The transducer should be roughly parallel to the ground. The transducer's centerline should be in line with the bot- tom of the hull. Don't let the bracket extend below the hull! Mark the center of each sl...

14 Route cable over bolt and through bracket. Side view shown at left and seen from above at right. Attach the transducer to the transom. Slide the transducer up or down until it's aligned properly with the bottom of the hull as shown in the preceding and following figures. Tighten the bracket's mou...

15 Align transducer centerline with hull bottom and attach to transom. 6. Route the transducer cable through or over the transom to the sonar unit. Make sure to leave some slack in the cable at the transducer. If possible, route the transducer cable away from other wir- ing on the boat. Electrical n...

16 located above the waterline. After installation, be sure to seal the hole with the same marine grade above- or below-waterline seal-ant used for the mounting screws. 7. Make a test run to determine the results. If the bottom is lost at high speed, or if noise appears on the display, try sliding t...

17 3. Route the transducer cable alongside the trolling motor shaft. Use plastic ties (not included) to attach the transducer cable to the trolling motor shaft. Make sure there is enough slack in the cable for the motor to turn freely. Route the cable to the sonar unit and the transducer is ready fo...

18 Transducer angles and their effects on fish arches. If the arch slopes up – but not back down – then the front of the trans- ducer is too high and needs to be lowered. If only the back half of the arch is printed, then the nose of the transducer is angled too far down and needs to be raised. Tran...

19 NOTE: Periodically wash the transducer's face with soap and water to re- move any oil film. Oil and dirt on the face will reduce the sensitiv- ity or may even prevent operation. Shoot-Thru-Hull Preparation Hulls With Flotation Materials The transducer installation inside a fiberglass hull must be...

20 For example, some (but not all) manufacturers use a layer of fiberglass, then a core of balsa wood, finishing with an outer layer of fiberglass. Removing the inner layer of fiberglass and the balsa wood core exposes the outer layer of fiberglass. The transducer can then be epoxied di- rectly to t...

21 (more rocky) the bottom, the easier it will be to get a second bottom sig- nal.) Don't touch the controls once they've been set. Example of a second bottom signal. Unit is in 30 feet of water, with range set at 80 feet and sensitivity set at 87 percent. 2. Next, take the transducer out of the wat...

23 Epoxy transducer to hull. WARNING: Use only the epoxy available from LEI. It has been for- mulated to work with these installation procedures. Other epoxy types may be too thin or may not cure to the right consistency for optimum transducer perform-ance. 2. The epoxy consists of the epoxy itself ...

25 Speed/Temperature Sensors The FishEasy 240 family can accept as many as two temperature sensors, which can be used to monitor the temperature of surface water, a live well or some other location. These units can accept an optional speed sensor for showing speed and distance traveled. However, you...

28 Sonar unit with external speed sensor. Temp sensor is built into transducer. Speed Sensor Installation If you wish to purchase an optional sensor for your unit, refer to the accessory ordering information inside the back cover of this manual. The following instructions describe how to install the...

29 First find a location on the boat's transom where the water flow is smoothest. Don't mount the sensor behind strakes or ribs. These will disturb the water flow to the speed sensor. Make sure the sensor will remain in the water when the boat is on plane. Also make sure the lo- cation doesn't inter...

30 Speed sensor mounting configuration: side view (left) and rear view (right.) If the base of the transom has a radius, fill the gap between the tran- som and the sensor with the caulking compound. This will help ensure a smooth water flow. Route the sensor's cable through or over the transom to th...

32 If possible, keep the power cable away from other boat wiring, espe- cially the engine's wires. This will provide the best isolation from elec- trical noise. The power cable has two wires, red and black. Red is the positive lead, black is negative or ground. Make sure to attach the in-line fuse h...

34 Front view (left) and side view (right) showing dimensions of the FishEasy 240 when mounted on quick release bracket. After drilling the hole, pass the connectors up through the hole from under the dash. If you wish, you can fill in the hole around the cable with a good marine caulking compound. ...

35 Align the bracket over the cable hole with the cable slots facing away from you and fit the cable through one of the slots. Fasten the bracket to the dash using the three screw holes. FishEasy 240 quick release mounting bracket. Slots in the base allow routing the cable from beneath the mount. At...

38 PPP-12 Portable Power Pack with FishEasy 240 stowed for transport. Turn the sonar unit on. If it doesn't work, make sure the battery termi- nals are making good contact against the battery contacts. Also check the wiring connections on the battery adapter. The red wire on the power cable should b...

39 Portable Transducer Assembly Recommended tools for installation include a slotted screw driver and two adjustable wrenches. Assemble the transducer and bracket as shown in the following figure. Attach the transducer to the bracket with the supplied hardware. Make sure there is one washer on each ...

40 allow the bracket to extend below the hull, because water pressure against it can cause the suction cup to come off at speed. Moisten the cup, then press it onto the hull as firmly as possible. Tie the nylon cord to the boat and route the transducer cable to the sonar unit. Your portable sonar is...

41 Operation Keyboard Basics The unit sounds a tone when you press any key. This tells you the unit has accepted a command. Numbers in the figure correspond to key ex- planations below: Eagle FishEasy 240 Sonar, showing screen and keyboard. 1. PWR/CLEAR (power and clear) This key appears in the manu...

42 3. MENU DOWN (menu down) These keys appears in the manual text as MENU UP or MENU DOWN . Most of the time, the instructions require you to press either menu key, so the text simply uses the word MENU . Usually, when we say MENU , you can simply press the MENU UP key for consistency. This sonar un...

43 This screen shows a typical menu, the Scroll Speed menu. Display – Opening Screen The lights flash for about 10 seconds when the unit is turned on. The backlight menu first appears on the screen. To turn the lights on, press UP ARROW . If you don’t press a key, the menu will disappear after a few...

45 Chart menu. Chart is running or scrolling normally at left. Chart is stopped at right, and "Stopped" warning message appears. Screen Display Modes or Pages The FishEasy 240 has three screen display modes, or "Pages:" Full Chart page, Split Chart page and Large Digital page. The Fi...

46 page. (The screen changes as you move through the menu.) When the page you want is selected, press PWR to clear the menu. Full Chart This shows all echoes scrolling across the full screen. This is the default page. The bottom signal scrolls across the screen from right to left. Depth scales on th...

47 Split Chart page with normal view at right; zoomed view at left. Lrg Digital (Large Digital) The Large Digital page shows all information in big numbers. The digi- tal depth display is at the top of this screen, followed by the tempera- ture, speed, and distance readings. NOTE: Temperature, speed...

48 Range When turned on for the first time, the unit automatically adjusts the depth range according to water conditions. It always keeps the bottom displayed in the lower portion of the screen. You can over-ride the automatic range control and manually select a range. To do this, press MENU until t...

51 Sensitivity Sensitivity controls the unit's ability to pick up echoes. If you want to see more detail, try increasing the sensitivity, a little at a time. There are situations when too much clutter appears on the screen. Decreasing the sensitivity can reduce the clutter and show the strongest fis...

54 To adjust sensitivity: Press MENU until the S ENSITIVITY A DJUSTMENT menu appears. Press UP ARROW to increase the sensitivity, DOWN ARROW to decrease it. When it's set at the desired level, press PWR to clear the menu. The sensitivity percentage in use shows in this menu. As you change the settin...

56 displays a small fish symbol when it thinks a target is a small fish, a medium fish symbol on a larger target and so forth. At left, underwater scene in normal fish arch mode. Right, Fish I.D. menu with the feature turned on. Fish I.D. is an easier way for a sonar novice to recognize a fishy sign...

57 out of reading the screen. Remember: Fish I.D. is one of the many tools we provide so you can analyze your sonar returns for maximum fish finding information. This and other features can help you successfully "see" beneath the boat under varied water and fishing conditions. So, practice w...

58 Fish ID menu and symbol with FishTrack on. The fish is 44 feet deep. FishReveal  When displaying actual sonar returns, the FishReveal  feature helps show fish targets hidden by surface clutter, thermoclines, weed beds and other cover with 10 levels of gray tones. Normal operation (with FishReve...

59 At left FishReveal menu screen. The feature is off and screen is in normal mode. Right, Fish Reveal is on, in standard mode. There are two FishReveal modes: standard and inverted. In standard mode, the weakest echoes are white and the strongest echoes are black. Echoes in between vary in gray in ...

60 To turn FishReveal on, press MENU DOWN until C HART S ETUP appears, then press UP ARROW . Press MENU DOWN until C HART M ODE appears. Press DOWN ARROW to select the desired FishReveal mode. Press PWR to clear the menu. To return to normal operation, repeat the above steps, but select N ORMAL befo...

61 At right, Scroll Speed menu at default 60 percent setting. At left, Scroll Speed menu, with unit set to HyperScroll mode. If you are running fast, try a HyperScroll setting of 80 to 100 percent. When using HyperScroll, you may also need to manually decrease the sensitivity for best performance. D...

62 ASP is an effective tool in combating noise. In sonar terms, noise is any undesired signal. It is caused by electrical and mechanical sources such as bilge pumps, engine ignition systems and wiring, air bubbles pass- ing over the face of the transducer, even vibration from the engine. In all case...

63 Alarms The sonar unit has two different types of alarms, fish and depth. Fish Alarm The Fish Alarm sounds a tone when a fish symbol appears on the screen. The default setting is on, but the Fish I.D. feature must be turned on for fish alarms to work. To turn Fish I.D. on, press MENU until the F I...

65 shows the current deep alarm setting. When the number reaches the desired setting, press PWR to clear the menu. When the bottom depth goes deeper than the alarm’s setting, an alarm tone sounds and a mes- sage box appears on the screen. Deep Alarm menu. Press UP ARROW to silence the alarm. This tu...

66 System Setup menu. Display Adjustments Backlights The display is backlit for night use. To turn the backlight on or off, press MENU repeatedly until the B ACK L IGHT menu appears. Press UP ARROW to turn the light on or the DOWN ARROW to turn it off. Backlight menu.

67 Display Contrast The unit’s display contrast is adjustable to suit different lighting condi- tions. This will help you see the screen from different angles or at vari- ous times of the day. The default setting is 50 percent. To adjust the contrast, press MENU DOWN until the S YSTEM menu ap- pears...

68 Depth menu controls the unit of measure used to show depth. Temperature Units of Measure This unit can show the temperature (if a temperature sensor is attached) in degrees Fahrenheit or Celsius. To change the unit of measure, press MENU DOWN until the S YSTEM menu appears. Press UP ARROW , then ...

70 Reset Log menu. Preset Unit (reset all options) This command is used to reset all features, options and settings to their original factory defaults. This is useful when you have changed several settings and want to return the unit to basic automatic operation. Press MENU DOWN until S YSTEM appear...

71 System Info To show the operating software system information, press MENU DOWN until the S YSTEM menu appears, then press UP ARROW . Press MENU DOWN until the S YSTEM I NFO screen appears. Press PWR to clear the screen. System Info screen. Simulator This unit has a built-in simulator that shows a...

72 Simulator menu. NOTE: If you turn on your unit before attaching a transducer, it may enter a demo mode. The words "demo mode" flash on the bottom of the screen and a sonar chart plays much like the simulator. Unlike the simulator, the demo mode is for demonstration only, and will auto- ma...

73 Chart Setup menu. Limit Search The Limit Search command helps you maintain maximum chart detail when you are moving fast in deep water (about 200 feet). When turned on, Limit Search prevents the digital sonar from over-riding the sonar chart's depth range setting. Limit Search does this by preven...

74 The sonar chart must be in manual depth range mode to use the Limit Search command. To switch from auto depth range to manual, press MENU until the R ANGE menu appears. Use the arrow keys to select the desired range. When you're finished, press PWR to clear the menu from the display. Next, press ...

75 To change any of these options, press MENU DOWN until C HART S ETUP appears, then press UP ARROW . Use the MENU keys to cycle through the list and display the desired menu, then use the ARROW keys to select the desired number size or turn the numbers off. Press the PWR key to clear the menus. Men...

76 Scales menu, with scale on (left) and off (right). With the scale off, only the upper and lower limits (zero and 60 in this case) are displayed To turn the scale off, press MENU DOWN until C HART S ETUP appears, then press UP ARROW . Press MENU DOWN until S CALES appears, then press DOWN ARROW to...

77 Troubleshooting If your unit is not working, or if you need technical help, please use the following troubleshooting section before contacting the factory cus- tomer service department. It may save you the trouble of returning your unit for repair. For contact information, refer to the last page,...

78 Weak bottom echo, digital readings erratic, or no fish signals: 1. Make sure the transducer is pointing straight down. Clean the face of the transducer. Oil, dirt and fuel can cause a film to form on the transducer, reducing its effectiveness. If the transducer is mounted in- side the hull, be su...

79 2. Electrical noise from the boat's motor can interfere with the sonar. This causes the sonar to automatically increase its Discrimination or noise rejection feature. This can cause the unit to eliminate weaker signals such as fish or even structure from the display. Try using resis- tor spark pl...

81 Index A Accessories, 5, 35, 36 Alarms, 60 Depth Alarms, 61 Fish Alarm, 61 Antenna, 78 ASP  (Advanced Signal Processing), 24, 59 B Backlights / Lighting, 6, 64 Batteries, 9, 10, 33, 34, 38, 41, 75, 76, 78 C Contrast, 6, 63, 64, 65 D Depth Range, 24, 25, 42, 46, 47, 48, 49, 57, 71, 72, 76, 77 F Fi...

EAGLE ELECTRONICS FULL ONE-YEAR WARRANTY "We," "our," or "us" refers to EAGLE ELECTRONICS, a division of LEI, the manufacturer of this product. "You" or "your" refers to the first person who purchases this product as a consumer item for personal, family, or ho...

How to Obtain Service… …in the USA: We back your investment in quality products with quick, expert service and genuine Eagle replacement parts. If you're in the United States and you have technical, return or repair questions, please contact the Factory Customer Service Department. Before any produc...

Accessory Ordering Information for all countries To order Eagle accessories such as power cables or transducers, please contact: 1) Your local marine dealer or consumer electronics store. Most quality dealers that handle marine electronic equipment or other consumer electronics should be able to ass...