Dodge 2009 Dakota - Manuals

INTRODUCTION This Owner’s Manual has been prepared with the assis-tance of service and engineering specialists to acquaintyou with the operation and maintenance of your vehicle.It is supplemented by a Warranty Information Bookletand various customer-oriented documents. You areurged to read these pub...

WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op-erating procedures that could result in an accident orbodily injury. It also contains CAUTIONS against proce-dures that could result in damage to your vehicle. If youdo not read this entire manual, you may miss importantinformati...

VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle couldseriously affect its roadworthiness and safety andmay lead to an accident resulting in serious injury ordeath. INTRODUCTION 7 1

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . 12 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . 12 ▫ Locking Doors With The Key . . . . . . . . . . . . . 15 m Steering Wheel Lock — If Equipped . . . . . . . . . 15 ▫ If You...

A WORD ABOUT YOUR KEYS The authorized dealer that sold you your vehicle has thekey code numbers for your vehicle locks. These numberscan be used to order duplicate keys from your authorizeddealer. Ask your authorized dealer for these numbersand keep them in a safe place. Ignition Key Removal Automat...

NOTE: If you try to remove the key before you place the shift lever in PARK, the key may become temporarilytrapped in the ignition cylinder. If this occurs, rotate the key to the right slightly, then remove the key as de-scribed. If a malfunction occurs, the system will trap thekey in the ignition c...

CAUTION! An unlocked car is an invitation to thieves. Alwaysremove the key from the ignition and lock all thedoors when leaving the vehicle unattended. Manual Transmission — If EquippedWhen the steering wheel is in the LOCK position, thesteering and ignition systems are locked to provideantitheft pr...

Locking Doors With The Key You can insert the key into the door lock cylinder witheither side up. To lock the driver’s door, turn the keyrearward. To unlock the driver’s door, turn the keyforward. For external door lock lubrication, refer to“Body Lubrication” in Section 7. STEERING WHEEL LOCK — IF E...

VEHICLE SECURITY ALARM SYSTEM — IFEQUIPPED The Vehicle Security Alarm system monitors the vehicledoors and ignition for unauthorized operation. When theVehicle Security Alarm system is activated it will provideboth audible and visible signals. The horn will soundrepeatedly for the three minutes and ...

exit alarming mode, press the RKE transmitter UNLOCKbutton or start the vehicle with a programmed SentryKey t . The Vehicle Security Alarm system is designed to protectyour vehicle; however, you can create conditions wherethe system will arm unexpectedly. If you remain in thevehicle and lock the doo...

REMOTE KEYLESS ENTRY This system allows you to lock or unlock the doors oractivate the Panic Alarm from distances up to a maxi-mum of 66 ft (20 m) using a Remote Keyless Entry (RKE)transmitter. The RKE transmitter does not need to bepointed at the vehicle to activate the system. NOTE: The line of tr...

Horn Chirp ProgrammingThe horn chirp feature is shipped from the assemblyplant activated. If desired, this feature can be disabled byusing the following procedure: 1. Press and hold the LOCK button on the RKE trans-mitter. 2. After holding the LOCK button for four seconds, alsopress the PANIC button...

4. Test the Flash Lamps With Lock feature while outsideof the vehicle by pressing the LOCK button on the RKEtransmitter with the ignition in the OFF position and thekey removed. NOTE: Pressing the LOCK button on the RKE transmit- ter while you are in the vehicle will activate the VehicleSecurity Ala...

NOTE: Changes or modifications not expressly ap- proved by the party responsible for compliance couldvoid the user’s authority to operate the equipment. If your RKE Transmitter fails to operate from a normaldistance, check for these two conditions. 1. Weak batteries in the RKE transmitter. The expec...

6. After holding the UNLOCK button for four seconds,also press the PANIC button within six seconds. 7. When a single chime is heard, release both buttons.The chime is an indication that you have successfullyentered program mode. All RKE transmitters that are tobe programmed must be done so within 60...

2. Remove and replace the battery. When replacing thebattery, match the + sign on battery to the + sign on theinside of the battery clip, located on the back cover. Avoidtouching the new battery with your fingers. Skin oils maycause battery deterioration. If you touch a battery, clean itwith rubbing...

Once the vehicle has started, the engine will run for15 minutes. To cancel remote start, press the REMOTESTART button once. The parking lights will remain illuminated to indicatethat the vehicle has remote started and the engine is running. The lights will turn off when the ignition isturned to RUN ...

If you press the power door LOCK switch while the keyis in the ignition, and any front door is open, the powerlocks will not operate. This prevents you from acciden-tally locking your keys in the vehicle. Removing the key,or closing the door, will allow the locks to operate. A chime will sound if th...

4. Within 10 seconds, cycle the key from the LOCKposition to the ON position and back to LOCK position,a minimum of four times; ending in the LOCK position.(Do not start the engine.) 5. Within 30 seconds, press the driver’s door LOCKswitch in the LOCK direction. 6. A single chime will be heard to in...

5. Within 30 seconds, press the driver’s door LOCKswitch in the UNLOCK direction. 6. A single chime will sound to indicate the feature hasbeen changed. 7. To reactivate the feature, repeat the above Steps. 8. If a chime is not heard, program mode was canceledbefore the feature could be changed. If n...

WINDOWS Power Windows The control on the left front door has up-down switchesthat give you finger-tip control of all four power win-dows. There is a single opening and closing switch on thepassenger doors for passenger window control. Thewindows will operate when the ignition switch is turnedto the ...

WARNING! Never leave children alone in a vehicle. Leavingunattended children in a vehicle is dangerous for anumber of reasons. A child or others could be seri-ously or fatally injured. Don’t leave the key in theignition. A child could operate power windows,other controls, or move the vehicle. Auto D...

windows down or partially open. This is a normaloccurrence and can be minimized. If the buffeting occurswith the rear windows open, open the front and rearwindows together to minimize the buffeting. OCCUPANT RESTRAINTS Some of the most important safety features in yourvehicle are the restraint syste...

WARNING! (Continued) • Wearing a seat belt incorrectly is dangerous. Seatbelts are designed to go around the large bones ofyour body. These are the strongest parts of yourbody and can take the forces of a collision the best.Wearing your belt in the wrong place could makeyour injuries in a collision ...

plate and pull out the belt. Slide the latch plate up thewebbing as far as necessary to allow the belt to go aroundyour lap. 3. When the belt is long enough to fit, insert the latchplate into the buckle until you hear a “click.” WARNING! • A belt buckled into the wrong buckle will notprotect you pro...

WARNING! (Continued) • A belt that is worn under your arm is very danger-ous. Your body could strike the inside surfaces ofthe vehicle in a collision, increasing head and neckinjury and a belt worn under the arm can causeinternal injuries. Ribs aren’t as strong as shoulderbones. Wear the belt over y...

Adjustable Upper Shoulder Belt Anchorage In the front and second row outboard seats, the shoulderbelt can be adjusted upward or downward to helpposition the belt away from your neck. Push in on theanchorage release button to release the anchorage, andthen move it up or down to the position that fits...

Seat Belt Pretensioners The seat belts for front outboard seating positions areequipped with pretensioning devices that are designed toremove any slack from the seat belt system in the event ofa collision. These devices improve the performance of theseat belt by assuring that the belt is tight about...

NOTE: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ONor START position. Chrylser LLC does not recommenddeactivating BeltAlert t . 1. Turn the ignition switch to the OFF position andbuckle the driver’s seat belt. 2. Turn the ignition switch to ...

WARNING! (Continued) • If your vehicle is equipped with window bags, donot have any accessory items installed that willalter the roof, including adding a sunroof to yourvehicle. Do not add roof racks that require perma-nent attachments (bolts or screws) for installationon the vehicle roof. Do not dr...

WARNING! (Continued) • If the vehicle has window bags, they also needroom to inflate. Do not lean against the door orwindow. Sit upright in the center of the seat. Airbag System ComponentsThe airbag system consists of the following: • Occupant Restraint Controller • Side Remote Acceleration Sensors ...

position, in the ACC position, or not in the ignition,the airbags are not on and will not inflate. During a moderate-to-severe rear impact, the ORC mayonly deploy the seat belt pretensioners. • Also, the ORC turns on the AIRBAG warn-ing light in the instrument cluster for six toeight seconds for a s...

may be possible based on collision severity and occu-pant size. The steering wheel hub trim cover and theupper right side of the instrument panel separate andfold out of the way as the bags inflate to their full size.The bags fully inflate in about 50 - 70 milliseconds.This is about half of the time...

If a Deployment OccursThe airbag system is designed to deploy the airbagswhen the impact sensors detect a moderate-to-severefrontal collision, to help restrain the driver and frontpassenger, and then immediately deflate. NOTE: A frontal collision that is not severe enough to need airbag protection w...

WARNING! Deployed airbags and seat belt pretensioners cannotprotect you in another collision. Have the airbags,and both front seat belt retractor assemblies (w/pretensioners), replaced by an authorized dealer assoon as possible. Maintaining Your Airbag System WARNING! • Modifications to any part of ...

WARNING! (Continued) • It is dangerous to try to repair any part of the airbagsystem yourself. Be sure to tell anyone who workson your vehicle that it has an airbag system. NOTE: Perchlorate Material – special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. Enhanced Accident Resp...

restraint anchorage system. (Refer to “LATCH - ChildSeat Anchorage System” in this section.) • Rearward-facing child seats must NEVER be used inthe front seat of a vehicle with a front passenger airbagthat does not have a switch to turn the airbag Off. Anairbag deployment could cause severe injury o...

were provided with the child restraint system. The rearseat lower anchorages are round bars, located at the rearof the seat cushion where it meets the seatback, and arejust visible when you lean into the vehicle to install thechild restraint. You will easily feel them if you run yourfinger along the...

locking retractor seat belts, refer to 9 Automatic Locking Mode 9 in this section. If you have trouble tightening the lap/shoulder belt on the child restraint because, thebuckle or latch plate is too close to the belt path openingon the restraint, follow these steps. If the buckle iswebbing-mounted,...

WARNING! • With a child restraint installed in the rear passen-ger side locations, use care when adjusting thefront seat(s) rearward, to avoid the front seatbackcoming in contact with the belted child directlybehind the seat. The child could be injured. • Improper installation can lead to failure of...

Tether Straps at the Rear Passenger Seat (Crew Cab) 1. Route the child restraint tether strap under the headrestraint for the outboard seating positions, and thenthrough the anchor strap outer loop (webbing materialloop), located directly behind the child restraint. 2. Route the tether strap across ...

WARNING! An incorrectly anchored tether strap could lead toseat failure and injury to the child. In a collision, theseat could come loose and allow the child to crashinto the inside of the vehicle or other passengers, oreven be thrown from the vehicle. Use only the anchorpositions directly behind th...

UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . 80 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . . . 80 ▫ Outside Mirrors Folding Feature — IfEquipped ...

m Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 ▫ Manual Seat Adjustment . . . . . . . . . . . . . . . 115 ▫ Front Seats Manual Seat Recliners . . . . . . . . . 116 ▫ Manual Lumbar Support Adjustment — IfEquipped . . . . . . . . . . . . . . . . . . . . . . . . . . 117 ▫ Adj...

Power Mirrors The power mirror controls are located on the driver’sdoor trim panel. To adjust a mirror, turn the control wand toward the leftor right mirror positions indicated. Tilt the control wandin the direction you want the mirror to move. When youare finished adjusting the mirror, turn the con...

The UConnect t system is fully integrated with the vehi- cle’s audio system. The volume of the UConnect t system can be adjusted either from the radio volume controlknob or from the steering wheel radio control (rightswitch), if so equipped. The radio display will be used for visual prompts fromthe ...

Help CommandIf you need assistance at any prompt, or if you want toknow your options at any prompt, say 9 Help 9 following the beep. The UConnect t system will play all the options at any prompt if you ask for help. To activate the UConnect t system from idle, simply press the PHONE button and follo...

• To call one of the names in the list, press the “VoiceRecognition” button during the playing of the desiredname, and say 9 Call. 9 NOTE: The user can also exercise 9 Edit 9 or 9 Delete 9 operations at this point. • The UConnect t system will then prompt you as to the number designation you wish to...

has established, press and hold the PHONE button untilyou hear a double beep, indicating that the two calls havebeen joined into one conference call. Call TerminationTo end a call in progress, momentarily press the PHONEbutton. Only the active call(s) will be terminated and ifthere is a call on hold...

the paired cellular phone to call the emergency num-ber. This feature is supported in the U.S., Canada, andMexico. NOTE: • The emergency number dialed is based on the countrywhere the vehicle is purchased (911 for the U.S. andCanada and 060 for Mexico). The number dialed maynot be applicable with th...

• low-to-medium vehicle speed, • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speakingin North American English, French, and Spanish ac-cents, the system may not always work for some. • When navigating through ...

• smooth road surface, • fully closed windows, • dry weather conditions, and • operation from the driver’s seat. • Performance, such as audio clarity, echo, and loudnessto a large degree rely on the phone and network, andnot the UConnect t system. • Echo at the far end can sometimes be reduced bylow...

General Information This device complies with Part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions: • Changes or modifications not expressly approved bythe party responsible for compliance could void theuser’s authority to operate the equipment. • T...

Commands The Voice Recognition System understands two types ofcommands. Universal commands are available at alltimes. Local commands are available if the supportedradio mode is active. Changing the Volume 1. Start a dialogue by pressing the VR hard-key. 2. Say a command (e.g., HELP). 3. Use the ON/O...

Voice Training For users experiencing difficulty with the system recog-nizing their voice commands or numbers, the UConnect t system Voice Training feature may be used. 1. Press the VR hard-key, speak “System Setup” and onceyou are in that menu then speak “Voice Training.” Thiswill train your own vo...

WARNING! Adjusting a seat while the vehicle is moving isdangerous. The sudden movement of the seat couldcause you to lose control. The seat belt might not beproperly adjusted and you could be injured. Adjustany seat only while the vehicle is parked. Front Seats Manual Seat Recliners The front seats ...

WARNING! Do not ride with the seatback reclined so that theshoulder belt is no longer resting against your chest.In a collision you could slide under the seat belt andbe seriously or even fatally injured. Use the reclineronly when the vehicle is parked. Manual Lumbar Support Adjustment — IfEquipped ...

The seat angle can also be adjusted by using the twotoggle switches, tilting it up or down. Extended Cab/Crew Cab T Rear Seat More cargo space is available by lifting up on the rearseat cushion. The Crew Cab t Rear Seat is a 60/40 split cushion and full back. Either cushion can be raised, independen...

WARNING! • Persons who are unable to feel pain to the skinbecause of advanced age, chronic illness, diabetes,spinal cord injury, medication, alcohol use, ex-haustion or other physical condition must exercisecare when using the seat heater. It may cause burnseven at low temperatures, especially if us...

2. Then push the safety latch lever up while lifting thegrille with your hand. It is located at the bottom center ofthe grille. Lift the hood, and the gas filled props will hold it open. To prevent possible damage, do not slam the hood toclose it. Use a firm downward push at the center frontedge of ...

LIGHTS The headlight switch is located on the left side of theinstrument panel next to the steering wheel. Interior Lights Courtesy and dome lights are turned on when the frontdoors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to thesecond upward de...

NOTE: Club Cab t /Quad Cab t models may have an optional switched dome lamp that is operated by press-ing the lens. Battery Saver To protect the life of your vehicle’s battery, Load Shed-ding is provided for both the interior and exterior lights. If the ignition is OFF and any door is left ajar for1...

Headlight Delay To aid in your exit, your vehicle is equipped with aheadlight delay that will leave the headlight on for60 seconds. This delay is initiated when the ignition isturned OFF while the headlight switch is on, and then theheadlight switch is cycled off. The headlights will remainon for 60...

Plastic is not as scratch resistant as glass and thereforedifferent lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses andreducing light output, avoid wiping with a dry cloth. Toremove road dirt, wash with a mild soap solution fol-lowed by rinsing. Do not...

30 seconds when the RKE transmitter UNLOCK button ispressed, as part of the illuminated entry feature. Multifunction Lever The multifunction lever is located on the left side of thesteering column. Turn SignalsTo operate the turn signals, move the multifunction leverup to signal a right-hand turn or...

The arrow on either side of the instrument cluster flashesto indicate the direction of the turn, and proper operationof the front and rear turn signal lights. If an indicator failsto light when the multifunction lever is moved, it wouldsuggest that the switch or indicator lamp is defective. If a def...

WINDSHIELD WIPERS AND WASHERS The multifunction lever is located on the left side of thesteering column. Windshield Wipers The wipers and washers are operated by a switch in themultifunction lever. Turn the end of the multifunctionlever to select the desired wiper speed. High Beam/Low Beam Wiper/Was...

Windshield Washers To use the washer, push in on the washer knob on the endof the multifunction lever and hold while spray isdesired. If the washer knob is depressed while in thedelay range, the wiper will operate for several secondsafter the washer knob is released. It will then resume theintermitt...

WARNING! Tilting the steering column while the vehicle ismoving is dangerous. Without a stable steering col-umn, you could lose control of the vehicle and havean accident. Adjust the column only while the ve-hicle is stopped. Be sure it is locked before driving. ELECTRONIC SPEED CONTROL — IF EQUIPPE...

To Activate Push the ON/OFF button to the ON position. In theinstrument cluster, the word “CRUISE” illuminates toindicate that the system is on. NOTE: The Electronic Speed Control has been designed to shut down if multiple speed control buttons (i.e., SETand CANCEL) are operated simultaneously in or...

To Vary The Speed Setting When the Electronic Speed Control System is ON, thespeed can be increased by pressing and holding theRESUME/ACCEL button. When the button is released, anew set speed will be established. Tapping the ACCEL button once will result in a speedincrease of 1 mph (2 km/h). Each ti...

WARNING! Electronic Speed Control can be dangerous where thesystem cannot maintain a constant speed. Your ve-hicle could go too fast for the conditions, and youcould lose control. An accident could be the result.Do not use Electronic Speed Control in heavy trafficor on roads that are winding, icy, s...

Courtesy/Reading Lights Near the front of the console are two courtesy/readinglights. Both lights illuminate as courtesy lights when a door isopened, when the dimmer control is rotated to thecourtesy light position (fully upward position), or whenthe UNLOCK button is pressed on the Remote KeylessEnt...

US/M Button Use the US/M button to change the display from U.S. tometric measurement units. RESET Button Use the RESET button to reset the following displays: • Average Fuel Economy • Trip Odometer • Elapsed time. US/M Button RESET Button UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 3

STEP Button Use the STEP button to choose, or cycle through, the fourtrip conditions. Average Fuel Economy (AVG ECO) Displays the average fuel economy since the last reset.Average fuel economy is a running average of the amount of fuel used and the distance the vehicle hastraveled. When the fuel eco...

NOTE: Magnetic materials should be kept away from the Overhead Console. This is where the compass sensoris located. Manual Compass Calibration NOTE: To ensure proper compass calibration, make sure the compass variance is properly set before manu-ally calibrating the compass. If the compass appears e...

To set the variance: Turn the ignition ON and set thedisplay to “Compass/Temperature.” Press and hold theRESET button approximately five seconds. The last vari-ance zone number will be displayed. Press the STEPbutton to select the new variance zone and press theRESET button to resume normal operatio...

NOTE: HomeLink t is disabled when the Vehicle Theft Alarm is active. WARNING! Your motorized door or gate will open and close whileyou are training the Universal Transceiver. Do not trainthe transceiver if people or pets are in the path of thedoor or gate. Only use this transceiver with a garagedoor...

WARNING! Vehicle exhaust contains carbon monoxide, a danger-ous gas. Do not run your vehicle in the garage whiletraining the transceiver. Exhaust gas can cause seri-ous injury or death. Programming HomeLink T Before You BeginThe Compass Mini-Trip Computer (CMTC) illuminatesthe HomeLink t symbol (a h...

6. Firmly press and release the “learn” or “training”button. The name and color of the button may vary bymanufacturer. NOTE: There are 30 seconds in which to initiate the next step after the “Learn” button has been pressed. 7. Return to the vehicle and press the programmedHomeLink t button twice (ho...

transmission – which may not be long enough forHomeLink t to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators aredesigned to “time-out” in the same manner. It may be helpful to unplug the device during the cyclingprocess, to prevent possible overheating o...

2. This device must accept any interference that may bereceived including interference that may cause undesiredoperation NOTE: The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications notexpressly approved by the party responsible for compli-ance could void the...

Electrical Outlet Use With Engine OFF (BatteryFed Configuration) CAUTION! • Many accessories that can be plugged in, drawpower from the vehicle’s battery, even when not inuse (i.e., cellular phones, etc.). Eventually, ifplugged in long enough, the vehicle’s battery willdischarge sufficiently to degr...

A two-cavity cupholder is available on all Crew Cabs t , with rear seats mounted on the floor. REAR STORAGE — IF EQUIPPED Rear Convenience Storage Crates The rear convenience storage crates are located under therear seat lower cushion and consist of two removable,collapsible storage crates. Front Cu...

WARNING! Do not sit or stand on this crate. It may collapsecausing serious injury. CAUTION! Do not lift up on the “End Flaps” to open the crate,damage to the “End Flaps” may occur. NOTE: The maximum loading capacity for the small crate is 30 lbs (13.6 kg) (and 50 lbs (22.6 kg) for the largecrate. To...

To install the crate into the base, insert the crate into theinboard slot and push down on the outboard side of thecrate, and snap into place. To collapse the crate, push the crate end flaps inward todisengage. Push the sides inward and snap into the base. Plastic Grocery Bag Retainers Retainer hook...

FLOOR CONSOLE — IF EQUIPPED Floor Console Features The Floor Console between the driver’s and front pas-senger’s seat has the following features: • Miscellaneous storage compartments. • Three cupholders (two removable). • iPod/Phone storage bin. • 12-Volt power outlet inside storage compartment. • S...

inside of the armrest lid. A tissue holder is also providedon the inside of the armrest lid, which holds a pocket-sizesoft pack of tissue. REAR CARGO AREA UTILITY RAILS CAUTION! The maximum load per cleat should not exceed320 lbs (145 kg) and the angle of the load on eachcleat should not exceed 60 d...

To remove the cleats from the utility rail, remove the endcap by pushing up on the locking tab, located on thebottom of the end cap. Slide the cleat off the end of therail. REAR WINDOW FEATURES Rear Window Defroster — If Equipped CAUTION! Use care when washing the inside of the rear windowto prevent...

prior to the time-out. The Rear Window Defroster willturn off automatically after 15 minutes from the firstactivation, and 10 minutes after the second activation, allwithin the same ignition cycle. To prevent excessivebattery drain, use the rear defroster only when the engineis running. Sliding Rear...

available from your authorized dealer. For safety reasons,follow all instructions on this important document. General Information The Manufacturer’s Warranty does not apply to bodymodifications and special equipment, such as a camperunit, heaters, stoves, refrigerators, etc., supplied bymanufacturer...

3. Lift the tailgate off of the pivot on the passenger sideby pulling upward and rearward at the same time. 4. Slide the tailgate to the passenger side while makingsure clearance from the box and taillight is maintained. To reinstall the tailgate, do the following: 1. Slide the tailgate onto the dri...

2. Secure the tailgate in the partially-open position: 3. Open the tailgate slightly. 4. Snap the tailgate support cable between the cableguide and the tailgate bumper. Do this on both sides ofthe tailgate. 1 — Bulkhead Divider Slot2 — Wheel Housing Indentions Tailgate Guide 160 UNDERSTANDING THE FE...

To return the tailgate to the full-open position: 1. Lift up on the tailgate. 2. Remove both cables from between the cable guidesand the tailgate bumpers, and lower the tailgate. CAUTION! • Care should always be exercised when operating avehicle with cargo. Vehicle speeds may need to bereduced. Seve...

UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instruments And Controls . . . . . . . . . . . . . . . . 166 m Instrument Cluster . . . . . . . . . . . . . . . . . . . . . 167 m Instrument Cluster Description . . . . . . . . . . . . 168 m Electronic Digital Clock . . . . . . . . . . . . . . . . . 179...

INSTRUMENTS AND CONTROLS 1 - Headlight Switch 6 - Glove Compartment 11 - Transfer Case Switch* 2 - Air Outlets 7 - Radio 12 - Speed Control Switches 3 - Demister Outlets 8 - Climate Controls 13 - Hood Release 4 - Instrument Cluster 9 - Power Outlet 14 - Parking Brake Release 5 - Airbags 10 - Heated ...

INSTRUMENT CLUSTER UNDERSTANDING YOUR INSTRUMENT PANEL 167 4

INSTRUMENT CLUSTER DESCRIPTION 1. Fuel GaugeThe fuel gauge shows the level of fuel in the fuel tankwhen ignition switch is in the ON position. 2. Temperature GaugeThe temperature gauge shows engine coolant tempera-ture. Any reading within the normal range indicates thatthe engine cooling system is o...

WARNING! A hot engine cooling system is dangerous. You orothers could be badly burned by steam or boilingcoolant. You may want to call a service center if yourvehicle overheats. If you decide to look under thehood yourself, see Section 7 of this manual. Followthe warnings under the Cooling System Pr...

is not functioning and that service is required. However,the conventional brake system will continue to operatenormally if the BRAKE warning light is not on. If the ABS light is on, the brake system should be servicedas soon as possible to restore the benefits of Anti-Lockbrakes. If the ABS light do...

CHAngE OIL and the outside temperature on vehiclesthat are not equipped with the Overhead Console withCompass/Temperature Mini-Trip Computer. If the vehicle diagnostic system determines that the fuelfiller cap is loose, improperly installed, or damaged,“GASCAP” will be displayed in the instrument cl...

CAUTION! The TPMS has been optimized for the originalequipment tires and wheels. TPMS pressures andwarning have been established for the tire sizeequipped on your vehicle. Undesirable system opera-tion or sensor damage may result when using re-placement equipment that is not of the same size,type, a...

27. Cargo LightThe Cargo Light indicator will illuminate when the CargoLight is activated by pressing the CARGO LIGHT button,located on the headlight switch. 28. TOW/HAULThe TOW/HAUL button is located at the end of the gearshift lever. This light will illuminate when the TOW/HAUL button has been sel...

3. After the hours are adjusted, push the TUNE/AUDIOcontrol knob to set the minutes. 4. Adjust the minutes by turning the TUNE/AUDIOcontrol knob. 5. To exit, press any button/knob, or wait approximatelyfive seconds. SALES CODE REQ — AM/FM STEREO RADIOAND 6–DISC CD/DVD CHANGER (MP3/WMA AUXJACK) NOTE:...

Power Switch/Volume Control (Rotary)Push the ON/VOLUME control knob to turn on theradio. Press the ON/VOLUME control knob a secondtime to turn off the radio. Electronic Volume ControlThe electronic volume control turns continuously (360degrees) in either direction without stopping. Turning theON/VOL...

Phone Button (UConnect t Hands-Free Phone) — If EquippedPress this button to operate the Hands-Free Phone(UConnect t ) feature (if equipped). Refer to “Hands-Free Communication (UConnect t )” in Section 3. If your vehicle is not equipped with or this feature is notavailable on your vehicle, a “Not E...

NOTE: The user will have to set these defaults before loading a disc. If changes are made to these settings aftera disc is loaded, changes will not be effective. Also, thedefaults are effective only if the disc supports thecustomer-preferred settings. AM and FM ButtonsPress the buttons to select AM ...

Notes On Playing MP3/WMA Files The radio can play MP3/WMA files; however, acceptableMP3/WMA file recording media and formats are limited.When writing MP3/WMA files, pay attention to thefollowing restrictions. Supported Media (Disc Types)The MP3/WMA file recording media supported by theradio are CDDA...

If a disc contains multi-formats, such as CD audio andMP3/WMA tracks, the radio will only play the MP3/WMA tracks on that disc. Supported MP3/WMA File FormatsThe radio will recognize only files with the *.MP3/WMAextension as MP3/WMA files. Non-MP3/WMA filesnamed with the *.MP3/WMA extension may caus...

Touch the screen where the words “Show Time if Radio isOff” are displayed to change the current setting. Changing the Time Zone 1. Turn on the multimedia system. 2. Touch the screen where the time is displayed. Theclock setting menu will appear on the screen. 3. Touch the screen where the words “Set...

Operating Instructions — Radio Mode NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary)Push the On/Volume control knob to turn on the radio.Push the On/Volume control knob a second time to turnoff the radio. Electronic Volume Control...

CAUTION! • This CD player will accept 4-3/4 in (12 cm) discsonly. The use of other sized discs may damage theCD player mechanism. • Do not use adhesive labels. These labels can peelaway and jam the player mechanism. • RES is a single CD player. Do not attempt to inserta second CD if one is already l...

RW/FFPress the RW button to stop the CD at the beginning ofthe current CD track/title. Press and hold FF (Fast Forward) and the CD player willbegin to fast forward until FF is released, or RW oranother CD button is pressed. The RW (Reverse) buttonworks in a similar manner. AM/FM ButtonPress the butt...

rates (VBR) are also supported. The majority of MP3 filesuse a 44.1 kHz sampling rate and a 192, 160, 128, 96 orVBR bit rate. MPEG Specifi- cation Sampling Fre- quency (kHz) Bit Rate (kbps) MPEG-1 Audio Layer 3 48, 44.1, 32 320, 256, 224,192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32 MPEG-2 Audio La...

Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, whichallows the user to plug in a portable device, such as anMP3 player, or cassette player, and utilize the vehicle’saudio system to amplify the source and play through thevehicle speakers. Pressing the AUX but...

SET/RND Button (Random Play Button)Press this button while the CD is playing to activateRandom Play. This feature plays the selections on thecompact disc in random order to provide an interestingchange of pace. Press the right SEEK button to move to the next ran-domly selected track. Press the SET/R...

exceeding 20 folders will result in this display. With200 files, exceeding 50 folders will result in thisdisplay.) • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator 9 . 9 and a three- character extension) • Level 2: 31 (including a separator 9 . 9 and a three-...

Operating Instructions - Hands-Free Phone(UConnect t ) (If Equipped) Refer to “Hands-Free Communication (UConnect t )” in Section 3. Operating Instructions - Satellite Radio Mode (IfEquipped)Refer to “Satellite Radio” in this section. SOUND BOX OPERATION The Sound Box includes one subwoofer, two twe...

SwitchPosition Light Operation 1 Pulse (right/passenger side) position – Inthis position the sound is active and thelights will pulse with the music. 2 Pulse off/light off (center) position – In thisposition the sound is active but the lightswill be turned off. 3 Constant (left/driver side) position...

1. The Electronic Serial Number/Sirius IdentificationNumber (ESN/SID). 2. Your Vehicle Identification Number. To access the ESN/SID, refer to the following steps: ESN/SID Access With REQ/RES RadiosWith the ignition switch in the ON/RUN or ACC posi-tion and the radio on, press the SETUP button and sc...

Operating Instructions — Hands-Free Phone (IfEquipped) Refer to “Hands-Free Communication (UConnect t )” in Section 3. Operating Instructions — Video EntertainmentSystem (VES)™ (If Equipped) Refer to separate “Video Entertainment System (VES)™Guide.” REMOTE SOUND SYSTEM CONTROLS — IFEQUIPPED The rem...

3. Do not apply paper or tape to the disc; avoid scratch-ing the disc. 4. Do not use solvents such as benzine, thinner, cleaners,or antistatic sprays. 5. Store the disc in its case after playing. 6. Do not expose the disc to direct sunlight. 7. Do not store the disc where temperatures may becometoo ...

Air Conditioning And Heater Air Conditioning And Heater OperationTo turn on the air conditioning, set the fan control at anyspeed and press the SNOWFLAKE button located at theright of the control panel. Conditioned air will be di-rected through the outlets selected by the mode control. A light at th...

Recirculation Modes (Panel or Bi-Level ) Select the recirculation modes whenthe outside air contains dust, odors,high humidity, or if rapid cooling isdesired. This feature allows for recir-culation of interior air only. Air flowseither through the panel outlets orboth the panel and floor outlets to-...

Blower Control The rotary knob on the left ofthe control panel is theBlower Control. Turn theknob clockwise to one of thefour positions to obtain theblower speed you desire. Toturn the blower off, turn theknob to the far left position. NOTE: For vehicles equipped with Remote Start, the climate contr...

Side window demisters direct airflow specifically to thewindow glass to help prevent interior fogging of theglass. They are located in the extreme outside upperedges of the instrument panel. The demisters also pro-vide extra air ducts for circulation. They are in operationwhenever the Floor, Mix, De...

Operation Tips Chart 234 UNDERSTANDING YOUR INSTRUMENT PANEL

STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . 239 ▫ Manual Transmission . . . . . . . . . . . . . . . . . . 239 ▫ Automatic Transmission . . . . . . . . . . . . . . . . 239 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . 240 ▫ Extreme Cold ...

Normal Starting NOTE: Normal starting of either a warm or cold engine is obtained without pumping or depressing the accelera-tor pedal. Turn the ignition switch to the START position andrelease when the engine starts. If the engine fails to startwithin 10 seconds, turn the key to the OFF position, w...

WARNING! Remember to disconnect the cord before driving.Damage to the 110-115 Volt electrical cord could causeelectrocution. MANUAL TRANSMISSION WARNING! You or others could be injured if you leave thevehicle unattended without having the parkingbrake fully applied. The parking brake should al-ways ...

Shifting Fully depress the clutch pedal before shifting gears. Asyou release the clutch pedal, lightly depress the accelera-tor pedal. You should always use 1st gear when starting from astanding position. Recommended Vehicle Shift SpeedsTo utilize your manual transmission efficiently for bothfuel ec...

Gear Selec- tion 6 to 5 5 to 4 4 to 3 3 to 2 2 to 1 Maxi- mum Speed 85 mph (135 km/h) 75 mph (120 km/h) 55 mph (88 km/h) 35 mph (56 km/h) 20 mph (32 km/h) Reverse Shifting To shift into REVERSE, bring the vehicle to a completestop. Depress the clutch and pause briefly to allow thegear train to stop ...

CAUTION! (Continued) • Before shifting into any gear, make sure your footis firmly on the brake pedal. WARNING! It is dangerous to move the shift lever out of PARK orNEUTRAL if the engine speed is higher than idlespeed. If your foot is not firmly on the brake pedal,the vehicle could accelerate quick...

If the transmission temperature gets extremely hot, thetransmission will automatically select the most desirablegear for operation at this temperature. If the transmissiontemperature becomes hot enough, the “Trans Temp” lightmay illuminate and the transmission may downshift outof Overdrive until the...

cause damage to the transmission. The torque converterwill refill within five seconds of shifting from PARK intoany other gear position. FOUR-WHEEL DRIVE OPERATION NV233/243 GII Transfer Case OperatingInformation/Precautions The NV233/243 is an electric-shift transfer case and isoperated by the 4WD ...

Transfer Case Position Indicator LightsTransfer case position indicator lights are located on theinstrument cluster. If there is no indicator light on orflashing, the transfer case position is in two-wheel drive(2WD). If the indicator light is on, the desired position(4WD LOCK and 4WD LOW) has been ...

Shifting Procedure - NV233/243 Transfer Case NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer casewill not shift, the indicator light for the previous positionwill remain ON, and the newly-selected position indica-tor light will continue to flas...

will remain ON. At this time, reduce speed and stopspinning the wheels to complete the shift. There may bea delay up to 10 seconds for the shift to complete after thewheels have stopped spinning. 4WD LOCK-to-4WD LOW or 4WD LOW-to-4WDLOCK NOTE: When shifting into or out of 4WD LOW, some gear noise ma...

3. While still rolling, rotate the transfer case controlswitch to the desired position. 4. After the position indicator light has stopped flashing,shift the transmission back into gear. Alternate Procedure 1. Bring the vehicle to a complete stop. 2. With the key ON and the engine either OFF orrunnin...

WARNING! On vehicles equipped with a limited-slip differen-tial, never run the engine with one rear wheel off theground. The vehicle may drive through the rearwheel remaining on the ground and cause you to losecontrol of the vehicle. Care should be taken to avoid sudden accelerations whenboth rear w...

POWER STEERING The standard power steering system will give you goodvehicle response and increased ease of maneuverabilityin tight spaces. The system will provide mechanicalsteering capability if power assist is lost. If for some reason the power assist is interrupted, it willstill be possible to st...

apparent, and/or the system is not functioning as antici-pated. Coordinate inspection efforts through an autho-rized dealer. WARNING! Fluid level should be checked on a level surface andwith the engine off to prevent injury from movingparts and to ensure accurate fluid level reading. Donot overfill....

Be sure the parking brake is firmly set when parked andthe shift lever is in the PARK position (automatic trans-mission), or REVERSE, or 1st gear (manual transmission).When parking on a hill, you should apply the parkingbrake before placing the shift lever in PARK, otherwise the load on the transmis...

When parking on a hill, turn the front wheels toward thecurb on a downhill grade and away from the curb on anuphill grade. The parking brake should be applied whenever thedriver is not in the vehicle. BRAKE SYSTEM In the event power assist is lost for any reason (forexample, repeated brake applicati...

TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger) - Metric tire sizing is based on U.S.design standards. P-Metric tires have the letter “P”molded into the sidewall preceding the size designa-tion. Example: P215/65R15 95H. • European-Metric tire sizing is based on Europeandesign standards. ...

Tires designed to this standard have the letter “T”molded into the sidewall preceding the size designa-tion. Example: T145/80D18 103M. • High flotation tire sizing is based on U.S. designstandards, and it begins with the tire diameter moldedinto the sidewall. Example: 31x10.5 R15 LT. Tire Sizing Cha...

EXAMPLE: 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding toits load index under certain operating condi...

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire,however, the date code may only be on one side. Tireswith white sidewalls will have the full TIN, including thedate code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of bl...

Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s sideB-Pillar. Tire and Loading Information Placard This placard tells you important information aboutthe:1) number of people that can b...

WARNING! (Continued) • Unequal tire pressures from one side of the ve-hicle to the other can cause the vehicle to drift tothe right or left. • Always drive with each tire inflated to the recom-mended cold tire inflation pressure. EconomyImproper inflation pressures can cause uneven wearpatterns to d...

CAUTION! After inspecting or adjusting the tire pressure, al-ways reinstall the valve stem cap (if equipped). Thiswill prevent moisture and dirt from entering thevalve stem, which could damage the valve stem. Inflation pressures specified on the placard are always“cold tire inflation pressure.” Cold...

loading may be required for high-speed vehicle opera-tion. Refer to original equipment or an authorized tiredealer for recommended safe operating speeds, loadingand cold tire inflation pressures. WARNING! High speed driving with your vehicle under maxi-mum load is dangerous. The added strain on your...

vehicle, but it is not. Installation of this limited-use sparetire affects vehicle handling. Since it is not the same tire,replace (or repair) the original tire and reinstall on thevehicle at the first opportunity. WARNING! The limited-use spare tires are for emergency useonly. Installation of this ...

Tread Wear Indicators Tread wear indicators are in the original equipment tiresto help you in determining when your tires should bereplaced. These indicators are molded into the bottom of the treadgrooves. They will appear as bands when the tread depthbecomes 1/16 in (2 mm). When the tread is worn t...

WARNING! Tires and the spare tire should be replaced after sixyears, regardless of the remaining tread. Failure tofollow this warning can result in sudden tire failure.You could lose control and have an accident resultingin serious injury or death. Keep dismounted tires in a cool, dry place with as ...

WARNING! • DO NOT use a tire, wheel size or rating other thanthat specified for your vehicle. Some combinationsof unapproved tires and wheels may change sus-pension dimensions and performance characteris-tics, resulting in changes to steering, handling, andbraking of your vehicle. This can cause unp...

CAUTION! (Continued) • Because of limited chain clearance between tiresand other suspension components, it is importantthat only chains in good condition are used. Bro-ken chains can cause serious vehicle damage. Stopthe vehicle immediately if noise occurs that couldsuggest chain breakage. Remove th...

Follow the recommended tire rotation frequency for yourtype of driving found in the “Maintenance Schedules”section of this manual. More frequent rotation is permis-sible if desired. The reasons for any rapid or unusualwear should be corrected prior to rotation being per-formed. TIRE PRESSURE MONITOR...

• Seasonal temperature changes will affect tire pressure,and the TPMS will monitor the actual tire pressure inthe tire. Base System – If Equipped The Tire Pressure Monitor System (TPMS) uses wirelesstechnology with wheel rim mounted electronic sensors tomonitor tire pressure levels. Sensors, mounted...

General Information This device complies with part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions: • This device may not cause harmful interference. • This device must accept any interference received,including interference that may cause undesired...

CAUTION! (Continued) • An out-of-tune engine, or certain fuel or ignitionmalfunctions, can cause the catalytic converter tooverheat. If you notice a pungent burning odor orsome light smoke, your engine may be out of tuneor malfunctioning and may require immediateservice. Contact your authorized deal...

ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and couldcause serious personal injury. Never have any smok-ing materials lit in or near the vehicle when remov-ing the fuel filler tube cap (gas cap) or ...

Selection Of Engine Oil For Flexible Fuel Vehicles(E-85) and Gasoline Vehicles FFV vehicles operated on E-85 require specially formu-lated engine oils. These special requirements are includedin MOPAR t engine oils, and in equivalent oils meeting Chrysler Specification MS-6395. The manufacturer onlyr...

CAUTION! Replacing fuel system components with non-ethanolcompatible components can damage your vehicle. ADDING FUEL Fuel Filler Cap (Gas Cap) The gas cap is located behind the fuel filler door. Whenfueling, the cap may be placed on the inside of the fillerdoor. If the gas cap is lost or damaged, be...

VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Admin-istration Regulations, your vehicle has a certificationlabel affixed to the driver’s side door. This label contains the month and year of manufacture,Gross Vehicle Weight Rating (GVWR), Gross Axle WeightRating (...

should then be determined separately to be sure that theload is properly distributed over front and rear axle.Weighing the vehicle may show that the GAWR of eitherthe front or rear axles has been exceeded but the totalload is within the specified GVWR. If so, weight must beshifted from front to rear...

Common Towing Definitions The following trailer towing related definitions will assistyou in understanding the following information: Gross Vehicle Weight Rating (GVWR)The GVWR is the total allowable weight of your vehicle.This includes driver, passengers, cargo and tongueweight. The total load must...

WARNING! An improperly adjusted weight-distributing hitchmay reduce handling, stability, and braking perfor-mance, and could result in an accident.Weight-Distributing Systems may not be compatiblewith surge brake couplers. Consult with your hitchand trailer manufacturer or a reputable recreationalve...

EXAMPLE — With Weight-Distributing Hitch (Correct) EXAMPLE — Improper Adjustment of Weight- Distributing Hitch (Incorrect) 314 STARTING AND OPERATING

Trailer Hitch Classification The rear bumper is intended to tow trailers up to2,000 lbs (907 kg) without added equipment or alter-ations to the standard equipment. Your vehicle may befactory equipped for safe towing of trailers weighingover 2,000 lbs (907 kg) with the optional Trailer Tow PrepPackag...

Trailer Towing Weights (Maximum Trailer WeightRatings) NOTE: For additional trailer towing information (maxi- mum trailer weight ratings) refer to the following websiteaddresses: • http:// www.dodge.com/towing • http:// www.dodge.ca (Canada) Trailer and Tongue Weight Always load a trailer with 60% t...

• The weight of any other type of cargo or equipmentput in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additionalfactory-installed options, or dealer-installed options,must be con...

CAUTION! If the trailer weighs more than 1,000 lbs (454 kg)loaded, it should have its own brakes and theyshould be of adequate capacity. Failure to do thiscould lead to accelerated brake lining wear, higherbrake pedal effort, and longer stopping distances. WARNING! Do not connect trailer brakes to y...

Towing Tips Before setting out on a trip, practice turning, stoppingand backing the trailer in an area away from heavytraffic. If using a manual transmission vehicle for trailer towing,all starts must be in 1st gear to avoid excessive clutchslippage. Towing Tips — Automatic TransmissionThe “D” range...

− When using the speed control, if you experience speed drops greater than 10 mph (16 km/h), disengage untilyou can resume cruising speed. − Use speed control in flat terrain and with light loads to maximize fuel efficiency. Towing Tips — Cooling SystemTo reduce potential for engine and transmission...

CAUTION! Damage to the transmission may occur if the trans-mission is shifted into PARK with the transfer case inNEUTRAL and the engine running. With the transfercase in NEUTRAL, ensure that the engine is off priorto shifting the transmission into PARK. Returning to Normal OperationUse the following...

WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . 332 m Changing A Flat Tire . . . . . . . . . . . . . . . . . . . 332 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . 332 ▫ Removing The Spare Tire . . . . . . . . . . . . . . . 334 ▫ Tire Chan...

HAZARD WARNING FLASHER The Hazard Warning Flasher switch is located on the topof the steering column, just behind the steering wheel. Press the switch and all front and rear directional signalswill flash intermittently. Press the switch a second time toturn off the emergency flashers. This is an eme...

The jack is secured in place by turning the jack screwuntil the jack is secured into place. A finger-operated helper tool is provided to assist re-moval and stowage of the jack. This tool must beremoved to operate the jack for changing the spare tire. Jack Stowage Location (Extended Cab) Jack Screw ...

WARNING! The jack is designed as a tool for changing tires only.The jack should not be used to lift the vehicle forservice purposes, unless suitable supports are placedunder the vehicle as a safety measure. The vehicleshould be jacked on a firm level surface only. Avoidicy or slippery areas. Removin...

Steps for Removing the Spare Tire • Remove the jack from the stowage compartment usingthe supplied finger-assist tool. • Remove the finger-assist tool from jack and set asideuntil jack is stowed. • Assemble the jack tools. • Locate the tire carrier access hole on the rear bumper. • Place assembled j...

It is recommended that you stow the flat or spare toavoid tangling the loose cable. NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or otherpower tools is not recommended and can damage thewinch. Turning Lug Wrench and Extension Spare Tire Stowag...

6. Block both the front and rear of thewheel diagonally opposite the jackingposition. For example, if the right frontwheel is being changed, block the leftrear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked. Instructions WARNING! Carefully follow these tire...

WARNING! (Continued) • If working on or near a roadway, be extremelycareful of motor traffic. • To assure that spare tires, flat or inflated aresecurely stowed, spares must be stowed with thevalve stem facing the ground. • Turn on the Hazard warning flasher. 1. Lower and remove the spare wheel, jack...

NOTE: Before raising the wheel off the ground, makesure that the jack will not damage surrounding truckparts and adjust the jack position as required. 5. By rotating the wheel wrench clockwise, raise thevehicle until the wheel just clears the surface. WARNING! Raising the vehicle higher than necessa...

WARNING! A loose tire or jack thrown forward in a collision orhard stop could injure someone in the vehicle. Al-ways stow the jack, tools and the extra tire and wheelin the places provided. 8. Lower the jack to its fully closed position. Stow thereplaced tire, jack, and tools as previously described...

To Stow the Flat or Spare Turn the wheel so that the valve stem is down. Slide thewheel retainer through the center of the wheel andposition it properly across the wheel opening. For convenience in checking the spare tire inflation, stowwith the valve stem toward the rear of the vehicle. Rotate the ...

WARNING! (Continued) • During cold weather when temperatures are be-low freezing point, electrolyte in a dischargedbattery may freeze. Do not attempt jump-startingbecause the battery could rupture or explode. Thebattery temperature must be brought up abovefreezing point before attempting jump-start....

FREEING A STUCK VEHICLE If vehicle becomes stuck in snow, sand, or mud, it canoften be moved by a rocking motion. Move the shift leverrhythmically between FIRST and REVERSE, while apply-ing slight pressure to the accelerator. The least amount of accelerator pedal pressure to main-tain the rocking mo...

WARNING! • Chains are not recommended for freeing a stuckvehicle. Chains may break, causing serious injuryor death. • Stand clear of vehicles when pulling with towhooks. Tow straps and chains may break, causingserious injury. CAUTION! Tow hooks are for emergency use only, to rescue avehicle stranded...

Two-Wheel Drive Vehicles Provided that the transmission is operable, tow with thetransmission in NEUTRAL and the ignition key in theOFF position, along with the front wheels raised and therear wheels on the ground. The speed must not exceed30 mph (50 km/h), and the distance must not exceed15 miles (...

MAINTAINING YOUR VEHICLE CONTENTS m Engine Compartment — 3.7L . . . . . . . . . . . . . 351 m Engine Compartment — 4.7L . . . . . . . . . . . . . 352 m Onboard Diagnostic System — OBD II . . . . . . . 353 ▫ Loose Fuel Filler Cap Message . . . . . . . . . . . 353 m Emissions Inspection And Maintenanc...

ENGINE COMPARTMENT — 3.7L 1 — Air Cleaner Filter 7 — Battery 2 — Automatic Transmission Dipstick 8 — Power Steering Fluid Reservoir 3 — Engine Oil Dipstick 9 — Engine Oil Fill 4 — Brake Fluid Reservoir 10 — Coolant Pressure Cap 5 — Clutch Fluid Reservoir (Manual Transmission Only) 11 — Washer Fluid ...

ENGINE COMPARTMENT — 4.7L 1 — Air Cleaner Filter 7 — Engine Oil Fill 2 — Automatic Transmission Dipstick 8 — Power Steering Fluid Reservoir 3 — Engine Oil Dipstick 9 — Coolant Pressure Cap 4 — Brake Fluid Reservoir 10 — Washer Fluid Reservoir 5 — Power Distribution Center 11 — Engine Coolant Reservo...

ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboarddiagnostic system called OBD II. This system monitorsthe performance of the emissions, engine, and automatictransmission control systems. When these systems areoperating properly, your vehicle will provide excell...

problem persists, the message will appear the next timethe vehicle is started. This might indicate a damaged cap.If the problem is detected twice in a row, the system willturn on the MIL. Resolving the problem will turn the MILoff. EMISSIONS INSPECTION AND MAINTENANCEPROGRAMS In some localities, it ...

5. Approximately 15 seconds later, one of two things willhappen: a. The MIL will flash for about 10 seconds and thenreturn to being fully illuminated until you turn OFFthe ignition or start the engine. This means that yourvehicle’s OBD II system is not ready and you shouldnot proceed to the I/M stat...

DEALER SERVICE Your authorized dealer has the qualified service person-nel, special tools and equipment to perform all serviceoperations in an expert manner. Service Manuals areavailable which include detailed service information foryour vehicle. Refer to these manuals before attemptingany procedure...

The engine oil filler cap also shows the recommendedengine oil viscosity for your vehicle. For information onengine oil filler cap location, refer to “Engine Compart-ment” in this section. Lubricants which do not have both the engine oil certi-fication mark and the correct SAE viscosity grade num-be...

Engine Air Cleaner Filter Refer to the “Maintenance Schedule” in Section 8 forproper maintenance intervals. WARNING! The air cleaner can provide a measure of protectionin the case of engine backfire. Do not remove the aircleaner unless such removal is necessary for repair ormaintenance. Make sure th...

WARNING! (Continued) • Battery gas is flammable and explosive. Keepflame or sparks away from the battery. Do not usea booster battery or any other booster source withan output greater than 12 volts. Do not allow cableclamps to touch each other. • Battery posts, terminals and related accessoriesconta...

include cleaning of the condenser fins and a performancetest. Drive belt tension should also be checked at thistime. WARNING! • Use only refrigerants and compressor lubricantsapproved by the manufacturer for your air condi-tioning system. Some unapproved refrigerants areflammable and can explode, in...

could result in failure of the joint due to water, and dirtcontamination of the grease. This would require com-plete replacement of the joint assembly. Refer to theService Manual for the detailed replacement procedure. Body Lubrication Locks and all body pivot points, including such items asseat tra...

WARNING! A hot exhaust system can start a fire if you park overmaterials that can burn. Such materials might begrass or leaves coming into contact with your exhaustsystem. Do not park or operate your vehicle in areaswhere your exhaust system can contact anything thatcan burn. In unusual situations i...

Cooling System WARNING! You or others can be badly burned by hot coolant orsteam from your radiator. If you see or hear steamcoming from under the hood, do not open the hooduntil the radiator has had time to cool. Never try toopen a cooling system pressure cap when the radiatoris hot. Engine Coolant...

of this. As long as the engine operating temperature issatisfactory, the coolant recovery bottle need only bechecked once a month. When additional engine coolant (antifreeze) is needed tomaintain the proper level, it should be added to thecoolant recovery bottle. Do not overfill. Points to Remember ...

• Keep the front of the radiator clean. If your vehicle isequipped with air conditioning, also keep the front ofthe condenser clean. • Do not change the thermostat for Summer or Winteroperation. If replacement is ever necessary, installONLY the correct type thermostat. Other designs mayresult in uns...

Use only brake fluid that has been in a tightly closedcontainer to avoid contamination from foreign matter ormoisture. CAUTION! Do not allow a petroleum-base fluid to contaminatethe brake fluid. Seal damage may result. Clutch Hydraulic System The clutch hydraulic system is a sealed maintenance-frees...

To check the automatic transmission fluid level properly,the following procedure must be used: 1. Operate the engine at idle speed and normal operatingtemperature. 2. The vehicle must be on level ground. 3. Fully apply the parking brake and press the brakepedal. 4. Place the gear selector momentaril...

CAUTION! Using a transmission fluid other than the manufac-turer’s recommended fluid may cause deteriorationin transmission shift quality and/or torque convertershudder. Using a transmission fluid, other than themanufacturer’s recommended fluid, will result inmore frequent fluid and filter changes. ...

components. Operation of the vehicle in water, as may beencountered in some off-highway types of service, willrequire draining and refilling the axle to avoid damage. Lubricant SelectionRefer to “Fluids, Lubricants, and Genuine Parts” in thissection for the correct fluid type. Rear AxleRear axle lim...

The most common causes are: • Road salt, dirt and moisture accumulation. • Stone and gravel impact. • Insects, tree sap and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly. Always wash your ve-hicle in the shade usin...

Special Care • If you drive on salted or dusty roads, or if you drivenear the ocean, hose off the undercarriage at least oncea month. • It is important that the drain holes in the lower edgesof the doors, rocker panels be kept clear and open. • If you detect any stone chips or scratches in the paint...

Stubborn soils can be removed easily with a soft clothand MOPAR t Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Pleasedo not use polishes, oils, cleaning fluids, solvents, deter-gents, or ammonia-based cleaners to clean your leatherupholstery. Applicatio...

This center contains cartridge fuses, mini fuses andrelays. A description of each fuse and component may bestamped on the inside cover, otherwise the cavity num-ber of each fuse is stamped on the inside cover that corresponds to the following chart. These fuses andrelays can be obtained from your au...

Cavity Cartridge Fuse Mini- Fuse Description 56 10 AmpRed Heated Seats 57 20 AmpYellow Airbag System # 2 58 20 AmpYellow Heated Seats 59 10 AmpRed HVAC Module 60 10 AmpRed ABS Module 61 20 AmpYellow Front Control Module(FCM) 3 (ReverseLamps) VEHICLE STORAGE If you are storing your vehicle for more t...

3. Grasp the headlight and pull firmly to disengage theheadlight housing from the fender panel. 4. While firmly holding the headlight housing in yourhands, unlock and disconnect headlight bulb connector. 5. Twist 1/4-turn and remove headlight bulb from hous-ing and replace. NOTE: The headlight bulb ...

Rear Side Marker, Taillamps/Stop Lamps, AndTurn Signal Bulbs — Replacement 1. Remove the two screws that pass through the bedsheet metal. 2. Pull the taillamp housing straight out from the body. MAINTAINING YOUR VEHICLE 389 7

License Lamps 1. Using a screwdriver, pry black rubber housing fromthe bumper. 2. Rotate the socket 1/4-turn counterclockwise. 394 MAINTAINING YOUR VEHICLE

3. Pull bulb from socket. 4. Reverse this procedure for installation. Fog Lights 1. Disconnect connector from fog light by raising thewire harness lock tab and pulling on wire harnessconnector. 2. Rotate fog light bulb 1/4-turn counterclockwise andpull to remove from fog light housing. 3. Reverse pr...

FLUIDS AND CAPACITIES U.S. Metric Fuel (Approximate) 22 Gallons 83 Liters Engine Oil with Filter3.7L Engine (SAE 5W-20, API Certified) 5 Quarts 4.7 Liters 4.7L/4.7L HO Engine (SAE 5W-20, API Certified) 6 Quarts 5.7 Liters Cooling System (Includes 2.1 Quarts/2 Liters for Cool-ant Bottle)3.7L Engine (...

MAINTENANCE SCHEDULES CONTENTS m Emissions Control System Maintenance . . . . . . 400 m Maintenance Schedule . . . . . . . . . . . . . . . . . . 400 ▫ Required Maintenance Intervals . . . . . . . . . . 402 8 M A I N TE N A N C E SC H E DU LE S

At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines. • Check the manual transmission fluid level. CAUTION! Failure to perform the required maintenance itemsmay result in damage to the vehicle. Required Maintenance Intervals NOTE: ** Vehicles built with the 4.7L eng...

IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For YourVehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 ▫ Prepare For The Appointment . . . . . . . . . . . . 419 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . 419 ▫ Be Reasonable Wi...

PUBLICATION ORDER FORMS To order the following manuals, you may use either thewebsite or the phone numbers listed below. Visa, Mas-tercard, American Express, and Discover orders are ac-cepted. If you prefer mailing your payment, please callfor an order form. NOTE: A street address is required when o...

Call toll free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the Worldwide Web at: • www.techauthority.com DEPARTMENT OF TRANSPORTATION UNIFORMTIRE QUALITY GRADES The following tire grading categories were established bythe National Highway Traffic Safety Administration. Thesp...

and are most concerned that you get prompt and highquality service. The manufacturer’s authorized dealershave the facilities, factory-trained technicians, specialtools, and the latest information to ensure the vehicle isfixed correctly and in a timely manner. This is why you should always talk to an...

In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240Sante Fe C.P. 05109Mexico, D. F.In Mexico City: 5081-4568Outside Mexico City: 1-800-505-1300 Customer Assistance For The Hearing Or SpeechImpaired (TDD/TTY) To assist customers who have hearing difficulties, themanufacturer has installed s...

Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 306Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 359Air Conditioner Maintenance . . . . . . . . . . . . . . . 360Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 229Air Conditioning, Operating Tips . . . . . . ...

Electric Powered . . . . . . . . . . . . . . . . . . . . . . . 81 Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Modifications/Alterations, Vehicle . . . . . . . . . . . . . 7Monitor, Tire Pressure System . ...

Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . 267Parking On Hill . . . . . . . . . . . . . . . . . . . . . . . . . 267Passing Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 128Pets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70Pets, Transporti...

Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . . 56Recreational Towing . . . . . . . . . . . . . . . . . . . . . . 324 Shifting into Transfer Case Neutral (N) . . . . . . . 325Shifting out of Transfer Case Neutral (N) . . . . . 327 Reformulated Gasoline . . . . . . . . . . . . . . . ...

Emergency (Jump Starting) . . . . . . . . . . . . . . . 343Engine Block Heater . . . . . . . . . . . . . . . . . . . . 241Engine Fails to Start . . . . . . . . . . . . . . . . . . . . 240Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Steering Column Controls . . . . . . . . . ...

2009 D A KOT A D A KOT A Chrysler LLC81-326-0934 First Edition Printed in U.S.A. OWNER’S MANUAL 2009