Dodge ES142 - Manual
Dodge ES142 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – ES142 Spring Return Electronic Actuators; Installation; Figure 2. Actuator Mounting Orientation.; Figure 3. Shaft Length and Proper Shaft Adapter Location.
- Page 3 – OR; Figure 5. Fasten the Mounting Bracket.
- Page 4 – Figure 6. Fasten the Shaft Adapter to the Damper Shaft.; Manual Override; HOLD; Rotating
- Page 5 – The Angular Rotation is Adjustable between; Mounting for NEMA 2; Figure 10. Acceptable NEMA 2 Mounting Positions.
- Page 6 – DIP Switch Features; Counterclockwise; Operating; Modulating Control
- Page 7 – Figure 13. Dual Auxiliary Switch Dials.
- Page 8 – Figure 14. The Minimum and Maximum Control Signal
- Page 9 – Wiring
- Page 12 – operating voltage is within range.; Service
- Page 13 – spring
- Page 16 – Dimensions; Figure 22. Dimensions of the ES142 Actuator and Mounting Bracket.
- Page 17 – Sizing Actuators for Damper Applications; Number of Actuators =; The same type of actuator is used.
- Page 18 – ACCESSORIES; This kit allows foot mounting of the ES142; Figure 4. Crank Arm Kit with Mounting Bracket.; This kit allows economical mounting of an
- Page 19 – This bracket provides an extended anti-; Service Parts; Special shaft adapter.
Dodge Engineering & Controls, Inc.
Toll Free (877) 334-2875 Fax: (978) 244-1422
Installation
ES142 Spring Return Electronic Actuators
129-270 EAI/ES-1 DEI,
Inc.
EA0655R1
a
b
f
d
g
h
c
e
Figure 1. Parts of the ES142 Actuator.
a. Actuator
b. Shaft
adapter
c. Position
indicator
d. Shaft adapter locking
clip
e. Position
indicator
adapter
f. Mounting bracket
(for dampers)
g. Mounting
screws
h. 3 mm hex wrench
Product Description
This installation instruction describes the steps for
direct-coupled mounting the ES142 series spring
return electronic actuator.
Product Numbers
ES142 (all versions)
Installation Conventions
Warning
Personal injury or loss of life may
occur if you do not perform a
procedure as specified.
Caution
Equipment damage or loss of data
may occur if you do not follow a
procedure as specified.
Required Tools
•
10 mm (13/32 in. open end wrench or ratchet
•
Drill
•
4 mm (5/32 in.) drill bit
•
3 mm hex wrench (provided)
•
Phillips
screwdriver
•
Marker or pencil
Expected Installation Time
30 minutes
Prerequisites
NOTE:
The actuator is shipped from the factory
with a 5° preload on the spring. The
position of the indicator points to the 0°
position. When power is applied to the
actuator, the preload is released.
WARNING:
Do not open the actuator.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Dodge Engineering & Controls, Inc. Toll Free (877) 334-2875 Fax: (978) 244-1422 Installation ES142 Spring Return Electronic Actuators 129-270 EAI/ES-2 DEI, Inc. Installation 90¡ EA1119R1 90¡ 2 1 2 Manual Overide Manual Overide NOTE: The actuator can be mounted for clockwise or counterclockwise r...
Dodge Engineering & Controls, Inc. Toll Free (877) 334-2875 Fax: (978) 244-1422 Installation ES142 Spring Return Electronic Actuators 129-270 EAI/ES-3 DEI, Inc. EA0288R1 1 2 3 4 OR EA0289R2 3 4 MANUAL OVERRIDE MANUAL OVERRIDE Place the actuator on the shaft with the damper blades in the desired ...
Dodge Engineering & Controls, Inc. Toll Free (877) 334-2875 Fax: (978) 244-1422 Installation ES142 Spring Return Electronic Actuators 129-270 EAI/ES-4 DEI, Inc. EA0697R1 10 mm HEX SOCKET 88 lb. - in. (10Nm) TORQUE 10 mm HEX SOCKET 88 lb. - in. (10Nm) TORQUE NOTE: Keep the shaft in the center of ...
