Dodge 2008 Viper - Manuals

WARNINGS AND CAUTIONS This manual contains WARNINGS against operatingprocedures, which could result in an accident or bodilyinjury. It also contains CAUTIONS against procedures,which could result in damage to your vehicle. If you donot read this entire manual, you may miss importantinformation. Obse...

VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle couldseriously affect its roadworthiness and safety andmay lead to an accident resulting in serious injury ordeath. INTRODUCTION 7 1

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . .12 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .13 m Security Alarm System . . . . . . . . . . . . . . . . . . ...

A WORD ABOUT YOUR KEYS You can insert the double-sided keys into the locks witheither side up. The dealer that sold you your new vehicle has the keycode numbers for your vehicle locks. These numbers canbe used to order duplicate keys from your dealer or alocksmith. Ask your dealer for these numbers ...

NOTE: The Power Accessory Delay feature allows you to operate the radio and the power windows for 2minutes after turning off the ignition switch. Removingthe key from the ignition switch and opening the driver’sdoor will cancel this feature. Your dealership can enableor disable the Power Accessory D...

Keyless Entry (RKE) transmitter. After the last door isclosed, or if all doors are closed, the system will arm itselfin approximately 16 seconds. During the arming process,the Vehicle Security Alarm Indicator light will flash at afast rate. Once the system is armed, the light will flashonce every 6 ...

Press the Trunk button on the RKE transmitter to allowaccess without triggering the alarm or having to disarmthe system. The trunk lid will pop open. Entering the liftgate with the System Armed —Coupe: NOTE: Using the key to open the liftgate while the system armed will trigger the alarm. Press the ...

• Press the UNLOCK button on the RKE transmitter.The front and rear park lights and the turn signallights will flash to acknowledge the signal. NOTE: The vehicle will not start unless the Vehicle Security Alarm System is disarmed by either method.Inserting the key in the ignition WILL NOT disarm the...

REMOTE KEYLESS ENTRY This system allows you to lock or unlock the doors, openthe trunk/liftgate, or activate the panic alarm fromdistances up to about 23 feet (7 meters) using a hand heldradio transmitter. The transmitter need not be pointed atthe vehicle to activate the system. To Unlock the Doors:...

Sound Horn with Remote Key LockThis feature will cause the horn to chirp when the doorsare locked with the transmitter. This feature can beturned on or turned off. To change the current setting,proceed as follows: 1. Press the LOCK button on a programmed transmitterfor at least 4 seconds, but no lon...

ON/RUN position. If not deactivated through the trans-mitter or the ignition switch, the alarm will turn offautomatically after 3 minutes. Programming Additional Transmitters NOTE: You must have at least one programmed trans- mitter to perform this procedure. If you do not have aprogrammed transmitt...

Battery Replacement The recommended replacement battery is 2016. This is ageneric battery, readily available at local retail stores. NOTE: • Perchlorate Material — special handling may apply.See www.dtsc.ca.gov/hazardouswaste/perchlorate. • Do not touch the battery terminals that are on the backhous...

2. Remove and replace the battery. Avoid touching thenew battery with your fingers. Skin oils may causebattery deterioration. If you touch a battery, clean it withrubbing alcohol. 3. To assemble the transmitter case, snap the two halvestogether. 4. Test the transmitter operation. General Information...

DOOR LOCKS WARNING! Do not touch the exhaust pipe sill covers whenentering or exiting your Viper. They can be hotenough to burn you. Observe the warning labels oneach door closure panel. WARNING! • For personal security and safety in the event of anaccident, lock the vehicle doors as you drive aswel...

Manual Door Lock The driver’s door can be locked or unlocked with the key.The door lock is located on the outside door panelbeneath the mirror. Power Door Locks A power door lock switch is on each door trim panel. Usethis switch to lock or unlock the doors. NOTE: To prevent you from accidentally loc...

Auto Down Feature Both windows have an auto down feature. Press thewindow switch to the second detent, release, and thewindow will go down automatically. Press the switch asecond time in either direction to stop the window. To open the window to a desired position, press and holdthe window switch in...

LIFTGATE — COUPE MODELS ONLY The liftgate can be unlocked or locked by the RemoteKeyless Entry (RKE) transmitter or by activating either ofthe power door lock switches located on the door trimpanels. To unlock the liftgate with the RKE transmitter, press theLIFTGATE button on the transmitter for at ...

NOTE: Gas props support the trunk lid in the open position. However, because the gas pressure drops withtemperature, it may be necessary to assist the props whenopening the trunk lid in cold weather. TRUNK SAFETY WARNING — CONVERTIBLEMODELS ONLY WARNING! Do not allow children to have access to the t...

OCCUPANT RESTRAINTS Some of the most important safety features in yourvehicle are the restraint systems. These include the seatbelts and the airbags for the driver and passenger. Please pay close attention to the information in thissection. It explains how to use your restraint systemproperly to kee...

WARNING! • It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in theseareas are more likely to be injured seriously or killed. • Do not allow people to ride in any area of your vehiclethat is not equipped with seats and seat belts. • Be su...

3. Slide the latch plate up the webbing as far as necessaryto make the belt go around your lap. 4. When the belt is long enough to fit, insert the latchplate into the buckle until you hear a “click.” WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap porti...

5. Position the lap belt across your thighs, below yourabdomen. To remove slack in the lap belt portion, pull upa little on the shoulder belt, as shown. 6. To loosen the lap belt if it is too tight, lift up on theshoulder belt and pull on the lap belt. A snug belt reducesthe risk of sliding under th...

8. To release the belt, push the red button in the buckle.The belt will retract automatically to its stowed position.If necessary, slide the latch plate down the webbing toallow it to retract fully. WARNING! A frayed or torn belt could rip apart in a collision andleave you with no protection. Inspec...

Enhanced Seat Belt Reminder System (BeltAlert T ) If the driver does not buckle their seat belt and vehiclespeed exceeds 5 mph (8 km/h), or if the passenger doesnot buckle their seat belt within 10 seconds of vehiclespeed exceeding 5 mph (8 km/h), the Enhanced WarningSystem (Belt Alert) will alert t...

NOTE: Watch for the Seat Belt Reminder light to turn on while unbuckling the seat belt and turn off while re-buckling the seat belt. It may be necessary to retract theseat belt. 6. Turn the ignition switch to the OFF/LOCK position. Asingle chime will sound to signify that you have com-pleted the pro...

NOTE: Once the belt is in automatic locking mode, you will not be able to pull any more of the webbing out ofthe retractor. In this mode, you will only be able to retractexcess webbing into the retractor to secure the childrestraint. How To Disengage The Automatic Locking ModeSimply allow all of the...

Driver and Passenger Supplemental RestraintSystem (SRS) - Airbag This vehicle is equipped with airbags for the driver andpassenger as a supplement to the seat belt restraintsystems. The driver airbag is mounted in the steeringwheel. The passenger airbag is mounted underneath acover in the passenger’...

The airbags work with the instrument panel knee bolstersand the seat belts to provide improved protection for thedriver and passenger. While the seat belts are designed toprotect the driver and passenger in many types ofcollisions, the airbags will deploy in moderate to severefrontal collisions. How...

• Steering Wheel and Column • Instrument Panel • Seat Track Position Sensors • Interconnecting Wiring • Seat Belt Reminder Light • Knee Impact Bolsters • Front Acceleration Sensors • Passenger Seat Occupant Classification System (OCS) − Occupant Classification Module (OCM) − Passenger Airbag Disable...

• The Knee Impact Bolsters help protect the knees ofthe driver and the passenger, and position everyonefor the best interaction with the airbags. • The Occupant Classification Module (OCM) is lo-cated underneath the passenger seat. The OCM usesinput from the Flex Mat to classify the occupant in thep...

may not classify the occupant properly. Furthermore,objects lodged under the seat can prevent the occu-pant’s weight from being measured properly and mayresult in the occupant being classified improperly. The passenger seat assembly contains critical compo-nents that affect passenger airbag deployme...

WARNING! Unapproved modifications or service procedures tothe passenger seat assembly, its related components,or seat cover may inadvertently change the airbagdeployment in case of a frontal crash. This couldresult in death or serious injury to the passenger ifthe vehicle is involved in an accident....

for airbag inflation. These airborne particles may irri-tate the skin, eyes, nose, or throat. If you have skin oreye irritation, rinse the area with cool water. For noseor throat irritation, move to fresh air. If the irritationcontinues, see your doctor. If these particles settle onyour clothing, fo...

NOTE: Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate. Airbag Warning Light You will want to have the airbags ready foryour protection in a collision. While the airbagsystem is designed to be maintenance free, ifany of the following occurs, have an a...

There are different sizes and types of restraints forchildren from newborn size to the child almost largeenough for an adult safety belt. Always check the childseat Owner’s Manual to ensure you have the correct seatfor your child. Use the restraint that is correct for yourchild: Infant and Child Res...

who weigh 20 to 40 lbs (9 to 18 kg) and who are olderthan one year. These child seats are also held in thevehicle by the lap/shoulder belt. The belt-positioning booster seat is for children weighingmore than 40 lbs (18 kg), but who are still too small to fitthe vehicle’s seat belts properly. If the ...

Here are some tips on getting the most out of your childrestraint: • Before buying any restraint system, make sure that ithas a label certifying that it meets all applicable SafetyStandards. We also recommend that you make surethat you can install the child restraint in the vehiclewhere you will use...

3. Remove the child tether access cover by prying eitherside with a screwdriver or similar tool, as shown. NOTE: While the child tether is in use, keep the access cover in a safe place so that it can be replaced after use ofthe child tether. 4. Pass the child restraint tether hook through eitheropen...

4. Tighten the lap portion of the belt and allow the excesswebbing to retract back to the retractor. If it still does notmake the child restraint secure, then secure the childrestraint with the Child Restraint Tether Anchor. NOTE: Once the belt is in automatic locking mode, you will not be able to p...

• Avoid excessive idling. • Check the engine oil level at every fuel fill. NOTE: A new engine will consume some oil during the first few thousand miles of operation. This should beconsidered as a normal part of the break-in and notinterpreted as a sign of difficulty. SAFETY TIPS Exhaust Gas Do not r...

UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS m Convertible Top Operation — ConvertibleModels Only . . . . . . . . . . . . . . . . . . . . . . . . . . .63 ▫ To Lower The Top . . . . . . . . . . . . . . . . . . . . . .63 ▫ To Raise The Top . . . . . . . . . . . . . . . . . . . . . .64 ▫ Convert...

CONVERTIBLE TOP OPERATION —CONVERTIBLE MODELS ONLY WARNING! The convertible top does not provide the structuralprotection that a reinforced metal roof does, and thefabric top cannot be expected to prevent the ejectionof the occupants of a vehicle in a collision. Therefore,it is important that all oc...

3. Depress the button located at the top of the latch andthen pull the latch handle downward and rearward. 4. Disengage the latch hook from the windshield receiverrod and then pull the latch all the way back to the detentstow position. 5. Pull the convertible top away from the windshieldheader. 6. R...

NOTE: Until the convertible top system has had ad- equate time to break-in, it may take a greater effort toengage the latch hook and close the latch. However,several weeks of normal convertible top usage willreduce these efforts. 9. Raise both sun visors if so desired. 10. Adjust the windows as desi...

Convertible Top Boot Cover Removal andStorage 1. Open the trunk. 2. On the driver side of the vehicle, pull upward on theboot cover to disengage the inboard tab. 3. Unclip the tab under the trunk lid stop and on theouter edge of the quarter panel flange. Disengaging Driver Side Tab 72 UNDERSTANDING ...

4. On the passenger side of the vehicle, pull upward onthe boot cover to disengage the inboard tab. 5. Unclip the tab under the trunk lid stop and on theouter edge of the quarter panel flange. 6. Slide the boot cover pockets off the front corners of theconvertible top. Disengaging Passenger Side Tab...

7. Fold the outer edges of the boot cover inward. 8. Fold the boot cover again. 9. Place the boot cover into the bag and store it in thetrunk or a secure dry area. 10. Close the trunk. Folding Outer Edges Folding Boot Cover 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

MIRRORS Inside Day/Night Mirror Adjust the mirror to center on the view through the rearwindow. A pivot system allows for horizontal and verti-cal mirror adjustment. Annoying headlight glare can be reduced by moving thesmall control under the mirror to the night position(toward rear of vehicle). The...

WARNING! Vehicles and other objects seen in the passenger sideconvex mirror will look smaller and farther awaythan they really are. Relying too much on yourpassenger side convex mirror could cause you tocollide with another vehicle or other object. Use yourinside mirror when judging the size or dist...

NOTE: When not in use, return the power mirror switch to the neutral (off) position to prevent accidental mirrormovement. SEATS Manual Seat Adjustments Forward & Rearward AdjustmentThe adjusting bar is at the front of the seat, near the floor.Pull the bar upward to move the seat forward or rear-...

WARNING! • Adjusting a seat while the vehicle is moving isdangerous. The sudden movement of the seatcould cause you to lose control. The seat belt mightnot be properly adjusted and you could be injured.Adjust the seat only while the vehicle is parked. • Do not ride with the seatback reclined so that...

TO OPEN AND CLOSE THE HOOD Two latches must be released to open the hood. First,reach into the lower right grille opening and pull theprimary hood latch forward. Next, raise the front of the hood slightly and push thesafety catch handle to the right. The safety catch handle islocated under the front...

NOTE: Assist props will raise the hood to a normal usage position. If greater access is required, the hood maybe pushed up at the front, raising the hood beyond theinitial opening height. CAUTION! Do not leave the hood open in areas where stronggusts of wind are likely. Such a place might be by thes...

This feature can be disabled at the dealership, if sodesired. Daytime Running Lights The fog lights will come on as Daytime Running Lights,whenever the ignition switch is on, the headlights are off,and the parking brake is off. The headlight switch mustbe used for normal night time driving. NOTE: Th...

You can also signal a lane change by moving the leverpartially upward or downward without moving beyondthe detent. The turn signals will continue to operate untilyou release the lever. If either light has a very fast flash rate, check for adefective outside light bulb. If an indicator fails to light...

Courtesy lights are also found in the driver’s foot well,the passenger’s foot well, and in the liftgate on Coupemodels. You can turn this light on and off from thedimmer control in the Multi-Function Lever. This light isalso controlled automatically by the illuminated entrysystem. Battery Saver Feat...

Instrument Panel Dimming With the parking lights or headlightson, rotate the dimmer control upwardto increase the brightness of the instru-ment panel lights or rotate it down-ward to decrease the brightness of theinstrument panel lights. Interior Light (ON) Rotate the dimmer control completelyupward...

WINDSHIELD WIPERS AND WASHERS The Windshield Wiper/Washer Control Lever ison the right side of the steering column. From the “OFF” position, push the Windshield Wiper/Washer Control Lever upward to the first detent past theintermittent “DEL” setting for Low-speed wiper opera-tion, or to the second d...

Adding Washer Fluid The windshield washer fluid reservoir is located in thefront of the engine compartment on the passenger side ofthe vehicle. Be sure to check the fluid level in thereservoir at regular intervals. Fill the reservoir withwindshield washer solvent (not radiator antifreeze) andoperate...

WARNING! Tilting the steering column while the vehicle ismoving is dangerous. Without a stable steering col-umn, you could lose control of the vehicle and havean accident. Adjust the column only while the ve-hicle is stopped. Be sure it is locked before driving. ADJUSTABLE PEDALS This feature allows...

To adjust the pedals: 1. Adjust the seat and steering column to a comfortableposition. 2. Either press the adjustable pedal switch forward tomove the pedals forward (toward the front of the ve-hicle), or pull the switch rearward to move the pedalsrearward (toward the rear of the vehicle). NOTE: • Al...

Adjustable Foot Rest This feature allows the driver to adjust the foot restforward or backward and to rotate it upward or down-ward to allow for greater driving comfort. To adjust the pedal: 1. Adjust the seat and steering column to a comfortableposition. 2. Using a 13 mm socket wrench, loosen the n...

UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instrument Panel Features . . . . . . . . . . . . . . . . . .95 m Instrument Cluster Description . . . . . . . . . . . . . .96 ▫ Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . .96 ▫ Message Center . . . . . . . . . . . . . . . . . . . . ....

INSTRUMENT PANEL FEATURES 1 — Air Outlet 7 — Speedometer/Odometer 13 — Climate Control 2 — Sound System Speaker 8 — Oil Pressure Gauge 14 — Engine Start Button 3 — Main Message Center 9 — Passenger Airbag Off Light 15 — Voltage Gauge 4 — Fuel Gauge 10 — Passenger Airbag 16— Engine Coolant Temperatur...

INSTRUMENT CLUSTER DESCRIPTION Speedometer Shows the vehicle’s speed in miles-per-hour (mph) and kilometers-per-hour (km/h). Odometer/Trip OdometerThe odometer shows the total distance the vehicle hasbeen driven. NOTE: U.S. federal regulations require upon transfer of vehicle ownership, the seller c...

standard non-anti-lock brakes. If this occurs, safely bringthe vehicle to a complete stop as soon as possible andcycle the ignition key to attempt to reset the ABS. If thelight remains on, see your authorized dealer immediatelyto have the system serviced. Furthermore, if the redBRAKE warning light a...

CAUTION! Prolonged driving with the light on could causefurther damage to the emission control system. Itcould also affect fuel economy and driveability. Thevehicle must be serviced before any state emissionstests can be performed. Turn Signal Indicators The left or right arrow will flash in unison ...

NOTE: The light will turn on when the ignition switch is in the ON/RUN position and the parking brake isapplied. This light shows only that the parking brake isapplied. It does not show the degree of brake application. WARNING! Driving a vehicle with the brake light on is danger-ous. Part of the bra...

6000 RPM. This serves as a visual aid to shift beforereaching the red line. This warning will turn off when thetachometer pointer falls below 5900 RPM. (See page 136for more information.) Coolant Temperature Gauge This gauge shows the engine coolant tempera-ture. The gauge pointer will likely show h...

between 20 and 80 psi (pounds per square inch). If thepointer remains in the red range, safely bring the vehicleto a complete stop and turn off the engine. DO NOToperate the vehicle until the cause is corrected. This gauge does not indicate the amount of oil in theengine. The engine oil level must b...

you understand and save you concern about these “ap-parent” malfunctions, you must understand a point ortwo about the transmission and reception of radio sig-nals. Two Types of Signals There are two basic types of radio signals: AM orAmplitude Modulation, in which the transmitted soundcauses the amp...

SALES CODE RAH — AM & FM STEREO RADIOWITH CD PLAYER AND CD/DVD CHANGERCONTROLS NOTE: The radio sales code is located on the lower left side of your radio faceplate. Radio Operation Power/Volume ControlPress the ON/VOL control to turn the radio on. Turn thevolume control clockwise to increase the...

NOTE: Changes or modifications not expressively ap- proved by the party responsible for compliance couldvoid the user’s authority to operate the equipment. CD Player Operation NOTE: • The ignition switch must be in the ON or ACCposition and the volume control ON before the CDplayer will operate. • T...

SeekPress the top of the SEEK button for the next selection onthe CD. Press the bottom of the button to return to thebeginning of the current selection, or return to thebeginning of the previous selection if the CD is within thefirst 10 seconds of the current selection. EJT — EjectPress the EJT butt...

CD audio tracks and computer files (including MP3 files).Discs created with an option such as 9 keep disc open after writing 9 are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result inlonger disc loading times. Supported MP3 file formatsThe radio will rec...

RW/FF (CD Mode For MP3 Play)Press the FF side of the button to move forward throughthe MP3 selection. Press the RW side of the button tomove back through the MP3 selection. AM/FM Button (CD Mode For MP3 Play)Switches back to Radio mode. RND Button (CD Mode For MP3 Play)Pressing this button plays fil...

System Activation Sirius Satellite Radio service is pre-activated, and youmay begin listening immediately to the one year ofSIRIUS audio service that is included with the factory-installed satellite radio system in your vehicle. Sirius willcontact you to supply a welcome kit and to confirmsubscripti...

one and stop the search. Pressing a pre-set memorybutton during a music type scan, will call up the memorychannel and stop the search. PTY Button ( SEEK ( When the desired program is obtained, press the 9 SEEK 9 button within five seconds. The channel will change tothe next channel that matches the ...

RADIO ANTENNA The radio antenna is located in the windshield. CD/DVD DISC MAINTENANCE To keep the CD/DVD discs in good condition, take thefollowing precautions: 1. Handle the disc by its edge; avoid touching thesurface. 2. If the disc is stained, clean the surface with a soft cloth,wiping from cente...

Air Conditioning and Heating System Blower Control Use this control to regulate theamount of air forced through the sys-tem in any mode you select. Turn thecontrol clockwise to increase fanspeed. Turn the control to the O — Offposition to shut off the fan and toprevent any outside air from enteringt...

Mode Control Use this control to select the directionof air flow. NOTE: The dot between the mode control icons is a mix position between the two modes. The mode settings are as follows: • Recirculation Control Air is recirculated inside the vehicle. Youmay choose between Bi-Level and Panel airoutlet...

• Defrost/Floor Air is directed through the windshield defrostand the floor outlets. This setting works best incold or snowy conditions that require extra heat at the windshield. This setting is good for maintainingcomfort while reducing moisture on the windshield. • Defrost Air is directed through ...

Operating Tips NOTE: Refer to the chart at the end of this section for suggested control settings for various weather condi-tions. Summer OperationThe engine cooling system in air-conditioned vehiclesmust be protected with a high-quality antifreeze coolantto provide proper corrosion protection and t...

STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . . 132 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . 133 ▫ If Engine Fails To Start . . . . . . . . . . . . . . . . . 135 ▫ After Starting . . . . . . . . . . . . . . . . . . . . . . . . 136 ...

STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust theinside and outside mirrors, fasten your seat belt, and ifpresent, instruct any other occupant to buckle their seatbelt. WARNING! • Never leave children alone in a vehicle. Leavingchildren in a vehicle unattended is dangero...

CAUTION! Long periods of engine idling, especially at highengine speeds, can cause excessive exhaust tempera-tures, which can damage your vehicle. Do not leaveyour vehicle unattended with the engine running. Normal Starting NOTE: • You must disarm the security system in order to startthe engine. For...

If Engine Fails to Start CAUTION! To prevent damage to the starter, do not crank theengine for more than 15 seconds at a time. Wait 10 to15 seconds before trying again. WARNING! • Never pour fuel or other flammable liquid into thethrottle body air inlet opening in an attempt tostart the vehicle. Thi...

If the engine is flooded, it may start to run, but not haveenough power to continue running when the start buttonis released. If this occurs, continue cranking up to 15seconds with the accelerator pedal pushed all the way tothe floor. Release the accelerator pedal and the startbutton once the engine...

driving. The noise may also be more noticeable whenthe transmission is warm. This noise is normal and isnot an indication of a problem with your clutch ortransmission. Recommended Shift Speeds To use your manual transmission for fuel economy itshould be upshifted as listed below. Shift at the vehicl...

Traction When driving on wet or slushy roads, it is possible for awedge of water to build up between the tire and roadsurface. This is hydroplaning and may cause partial orcomplete loss of vehicle control and stopping ability. Toreduce this possibility, the following precautions shouldbe observed: 1...

Flowing/Rising Water WARNING! Do not drive on or cross a road or a path where wateris flowing and/or rising (as in storm run-off). Flow-ing water can wear away the road or path’s surfaceand cause your vehicle to sink into deeper water.Furthermore, flowing and/or rising water can carryyour vehicle aw...

WARNING! • Driving through standing water limits your vehi-cle’s traction capabilities. Do not exceed 5 mph (8km/h) when driving through standing water. • Driving through standing water limits your vehi-cle’s braking capabilities, which increases stop-ping distances. Therefore, after driving through...

drops into the handle (releasing the lock), guide thehandle downward to its stop and then release the buttonand the handle. The Brake System Warning Light in the instrumentcluster will turn on when the ignition is in the ON/RUNposition and the parking brake is applied. NOTE: This light only shows th...

BRAKE SYSTEM Your vehicle is equipped with dual hydraulicbrake systems. If either of the two hydraulicsystems loses normal capability, the remainingsystem will still function. However, there will be some loss of overall braking effectiveness. You maynotice increased pedal travel during application, ...

Safe Operating Tips WARNING! To use your brakes and accelerator more safely, follow thesetips: • Do not “ride” the brakes by resting your foot on the pedal.This could overheat the brakes and result in unpredictablebraking action, longer stopping distances, or brake damage. • When descending mountain...

All vehicle wheels and tires must be the same size andtype as the original equipment and the tires must beproperly inflated to produce accurate signals for thecomputer. WARNING! Significant over or under inflation of tires, or mixingsizes of front or rear tires or wheels on the vehicle canlead to lo...

POWER STEERING The standard power steering system will give you goodvehicle response and increased ease of maneuverabilityin tight spaces. The system will provide mechanicalsteering capability if power assist is lost. If for some reason the power assist is interrupted, it willstill be possible to st...

TIRE SAFETY INFORMATION Tire Markings NOTE: • P (Passenger)-Metric tire sizing is based on U.S. designstandards. P-Metric tires have the letter “P” moldedinto the sidewall preceding the size designation. Ex-ample: P215/65R15 95H. • European Metric tire sizing is based on Europeandesign standards. Ti...

Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards 9 ....blank.... 9 = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = S...

EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load correspondingto its load index under certain operating conditions—The maximum speed correspondi...

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire,however, the date code may only be on one side. Tireswith white sidewalls will have the full TIN, includingdate code, located on the white sidewall side of the tire. Look for the TIN on the outboard side of black ...

Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side“B” pillar. Tire and Loading Information Placard This placard tells you important information about:1) the number of people that ca...

2. Economy—Improper inflation pressures can cause uneven wearpatterns to develop across the tire tread. These abnormalwear patterns will reduce tread life resulting in a need forearlier tire replacement. Under inflation, also increasestire rolling resistance and results in higher fuel consump-tion. ...

Many states have laws requiring tire replacement at thispoint. Life of Tire The service life of a tire is dependent upon varyingfactors including but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and spare tire should be replaced after six years,regardless of the r...

WARNING! • Do not use a tire, wheel size or rating other thanthat specified for your vehicle. Some combinationsof unapproved tires and wheels may change sus-pension dimensions and performance characteris-tics, resulting in changes to steering, handling, andbraking of your vehicle. This can cause unp...

aggressive tread designs such as those on all season typetires. Rotation will increase tread life, help to maintainmud, snow, and wet traction levels, and contribute to asmooth, quiet ride. Follow the “Maintenance Schedules” in Section 8 of thismanual for the recommended tire rotation frequency fory...

TIRE PRESSURE MONITOR SYSTEM (TPMS) Low Tire Indicator If tire pressure falls below 20 psi (138 kpa), the Low TirePressure Telltale in the Message Center will illuminate, achime will sound, and the words LOW TIRE will flashslowly in the Liquid Crystal Display (LCD) panel in thebottom of the speedome...

Materials Added to Fuel All gasoline sold in the United States is required tocontain effective detergent additives. Use of additionaldetergents or other additives are not needed undernormal conditions and they would result in additionalcost. Therefore, you should not have to add anything tothe fuel....

WARNING! • Never have any smoking materials lit in or nearthe vehicle when the gas cap is removed or thetank filled. • Never add fuel to the vehicle when the engine isrunning. • A fire may result if gasoline is pumped into aportable container that is inside of a vehicle. Youcould be burned. Always p...

TRAILER TOWING Trailer towing with this vehicle is not recommended. RECREATIONAL TOWING (BEHINDMOTORHOME, ETC.) TOWING THIS VEHICLE BEHIND ANOTHERVEHICLE (Flat towing with all four wheels on theground) Recreational towing for this vehicle is not recommended. NOTE: If the vehicle requires towing, mak...

WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 176 m If Your Engine Overheats . . . . . . . . . . . . . . . . . 176 m TIREFIT Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . 177 ▫ TIREFIT Storage . . . . . . . . . . . . . . . . . . . . . . 1...

HAZARD WARNING FLASHER The flasher switch is on the top of the steeringcolumn, just behind the steering wheel. Depress the flasher button and all front and rear directionalsignals will flash. Depress the flasher button again to turnoff the flashers. Do not use this emergency warning system when thev...

• In city traffic — While moving, shift into the highest gear possible to reduce engine RPM. NOTE: There are steps that you can take to slow down an impending overheat condition. If your air conditioneris on, turn it off. The air conditioning system adds heat tothe cooling system and turning off the...

TIREFIT Storage The TIREFIT kit is located in the trunk. TIREFIT Usage Precautions NOTE: • Replace the TIREFIT Sealant Bottle prior to the expi-ration date (printed on the bottle label) to assureoptimum operation of the system. • When the TIREFIT Sealant is in a liquid form, cleanwater, and a damp c...

WARNING! • Take care not to allow the contents of TIREFIT tocome in contact with hair, eyes, or clothing. TIRE-FIT is harmful if inhaled, swallowed, or absorbedthrough the skin: It causes skin, eye, and respira-tory irritation. Flush immediately with plenty ofwater if there is any contact with eyes ...

6. Air Pump Hose (Black) 7. Sealant Hose (Clear with Yellow Cap) Using the Mode Select Knob & Hoses Selecting Air Mode Turn the Mode Select knob (4) to this positionfor air pump operation only. Use the Black AirPump Hose (6) when selecting this mode. Selecting Sealant/Air Mode Turn the Mode Sele...

• Turn the Mode Select knob to the Sealant/Air Mode. • Connect the Power Plug (5) to a different poweroutlet in your vehicle or another vehicle, if available.Make sure the engine is running before turning onthe TIREFIT kit. • The Sealant Bottle (1) may be empty due to previoususe. Call for assistanc...

JUMP-STARTING PROCEDURES WARNING! • Take care to avoid the radiator cooling fans whenever the hoodis raised. They can start anytime the ignition switch is on. Youcan be hurt by the fans. • Take care to avoid the accessory drive whenever the hood israised. You can be hurt by the moving components. • ...

5. Remove the plastic cover from the remote jump-startpositive post (+) in the engine compartment. Refer to thefollowing illustration for remote jump-starting connec-tions. 6. If you are jump-starting your vehicle, connect oneend of a jumper cable to the positive (+) terminal on thebooster battery. ...

MAINTAINING YOUR VEHICLE CONTENTS m 8.4L Engine Compartment . . . . . . . . . . . . . . . . 194 m Onboard Diagnostic System (OBD II) . . . . . . . . . 195 m Emissions Inspection And MaintenancePrograms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 m Replacement Parts . . . . . . . . . ...

8.4L ENGINE COMPARTMENT 194 MAINTAINING YOUR VEHICLE

EMISSIONS INSPECTION AND MAINTENANCEPROGRAMS In some localities, it may be a legal requirement to passan inspection of your vehicle’s emissions control system.Failure to pass could prevent vehicle registration. For states, which have an I/M (Inspection andMaintenance) requirement, this check verifie...

5. Approximately 15 seconds later, one of two things willhappen: a. The MIL will flash for about 10 seconds and thenreturn to being fully illuminated until you turn off theignition key or start the engine. This means that yourvehicle’s OBD system is not ready and you should notproceed to the I/M sta...

DEALER SERVICE Your authorized dealer has the qualified service person-nel, special tools, and equipment to perform all serviceoperations in an expert manner. Service Manuals areavailable which include detailed service information foryour vehicle. Refer to these manuals before attemptingany procedur...

The best time to check the oil level is approximately 5minutes after a fully warmed engine is turned off orbefore starting the engine after it has sat overnight. Checking the oil while the vehicle is on level ground alsowill improve the accuracy of the oil level readings. Addoil only when the level ...

The engine oil filler cap also shows the recommendedengine oil viscosity for your engine. For information onengine oil filler cap location, refer to the “Engine Com-partment” illustration in this section. Materials Added to Engine OilThe manufacture strongly recommends against the addi-tion of any a...

quality filters should be used to assure most efficientservice. Mopar t Engine Oil Filters are a high quality oil filter and are recommended. Drive Belts — Check Condition and Tension Belt tension is controlled by means of an automatictensioner. Therefore, no belt tension adjustments arerequired. Ho...

WARNING! A hot exhaust system can start a fire if you park overmaterials that can burn. Such materials might begrass or leaves coming in contact with your exhaustsystem. Do not park or operate your vehicle in areaswhere your exhaust system can contact anything thatcan burn. In unusual situations inv...

NOTE: • Because of the plastic body shell on your vehicle,ignition cables should be replaced with the speciallydesigned RFI cables available at your dealer. • The ignition timing cannot be set on this engine. Crankcase Emission Control System Proper operation of this system depends on freedomfrom pl...

To Service the Battery: 1. Remove the floor portion of the rear compartmentcarpet to access the battery compartment. 2. Remove the battery cover mounting screws and re-move the battery cover. 3. Disconnect the negative battery cable from the battery. NOTE: The negative battery terminal is marked wit...

Battery Save Feature The Battery Save feature conserves battery power whenstoring the vehicle. It allows for up to 3 months of storagetime without losing radio and engine controller memory.Using this feature is an alternative to disconnecting thebattery. NOTE: This vehicle is designed to sit in stor...

4. Remove the key from the ignition switch and exit thevehicle. The Battery Save Feature will be enabled 45seconds after all doors are closed. NOTE: • Turning the ignition switch to the ON/RUN positionat any time will cancel activation of the Battery SaveFeature. • The remote keyless entry and the e...

Air Conditioner Maintenance For best possible performance, your air conditionershould be checked and serviced by an Authorized Dealerat the start of each warm season. This service shouldinclude cleaning of the condenser fins and a performancetest. Drive belt tension should also be checked at thistim...

Refrigerant Recovery and RecyclingR-134a Air Conditioning Refrigerant is a hydrofluorocar-bon (HFC) that is endorsed by the Environmental Pro-tection Agency and is an ozone-saving product. How-ever, the manufacturer recommends that air conditioningservice be performed by dealers or other service fac...

LubricationThe tie rod ends are lubricated for life. No periodiclubrication is required. Body Lubrication Locks and all body pivot points, including seat tracks,doors hinges, trunk/liftgate hinges, and hood hinges,should be lubricated periodically to assure quiet, easyoperation and to protect agains...

• Rubber bushings • Starter bearing • Throttle control cable • Water pump bearings Windshield Wiper Blades The rubber edges of the wiper blades and the windshieldshould be cleaned periodically with a sponge or soft clothand a mild nonabrasive cleaner. This will remove accu-mulations of salt or road ...

Exhaust System The best protection against carbon monoxide entry intothe vehicle body is a properly maintained engine exhaustsystem. If you notice a change in the sound of the exhaust system;or if exhaust fumes can be detected inside the vehicle; orwhen the underside or side of the vehicle is damage...

Cooling System WARNING! • When working near the radiator cooling fans,disconnect each fan motor lead or turn the ignitionswitch to the OFF position. The fans are tempera-ture controlled and can start any time the ignitionswitch is in the ON position. • You or others can be badly burned by hot coolan...

service attendant of this. As long as the engine operatingtemperature is satisfactory, the coolant bottle need onlybe checked once a month. When additional coolant is needed to maintain theproper level, it should be added to the coolant bottle. Donot overfill. Points to Remember NOTE: When the vehic...

Brake System In order to assure brake system performance, all brakesystem components should be inspected periodically.Recommended service intervals can be found in the“Maintenance Schedules” in this manual. WARNING! Riding the brakes can lead to brake failure andpossibly an accident. Driving with yo...

Rear Axle Axle Lubricant Level CheckCheck the exterior of the axle for evidence of gear oilleakage every 12 months or 6,000 miles (10 000 km). Thischeck should be made with the vehicle level and sup-ported by the suspension, with the vehicle on the groundor raised on an axle and wheel type hoist. Th...

In the event that you do take this vehicle to a commercialcar wash, move the Heater/Air Conditioning blowercontrol to the lowest setting. This will prevent the possi-bility of water entering the system. CAUTION! The tires on this vehicle are wider than the guidetracks on most washes and the low grou...

FUSES (POWER DISTRIBUTION CENTERS) Fuses (Power Distribution Center) A power distribution center is located in the enginecompartment on the driver’s side of the vehicle. Thiscenter contains fuses and relays. Cavity Car- tridgeFuse MiniFuse Description 1 40 AmpGreen — Blower Motor 2 40 AmpGreen — Ant...

Cavity Car- tridgeFuse MiniFuse Description 62, 63 — 15 AmpBlue Gauges 64, 65 — 10 AmpRed Airbag 66, 67 — 20 AmpYellow Wiper Switch 68, 69 — 20 AmpYellow Left HID Headlight 70, 71 — 20 AmpYellow Right HID Headlight CAUTION! • When installing the Power Distribution Centercover, it is important to ens...

Fuses (Mini-Power Distribution Center) A mini-power distribution center is located in the enginecompartment on the passenger’s side of the vehicle. Thiscenter contains radiator fan control relays and has twoexternally-mounted 40 Amp fuses for the radiator fans. CAUTION! • When installing the Mini-Po...

VEHICLE STORAGE We recommend that you follow these guidelines forstoring your vehicle for extended periods. • Fill the fuel tank. This will prevent water condensationinside the tank. If you plan to store your vehicle morethan 2 months, add an anti-oxidant fuel stabilizer tothe fuel tank. • Change th...

Then, either disconnect the battery at the negativeterminal or use the “Battery Save Feature” to conservebattery power. Refer to “Battery Save Feature” under“Maintenance Procedures” in this section for details. NOTE: Disconnecting the battery causes the engine control system to lose memory of some “...

BULB REPLACEMENT Auxiliary High Beam Headlight, Front Park/TurnSignal Light, Front Side Marker Light 1. Remove the push pin from the upper outer corner ofthe splash shield and remove the splash shield. 2. Turn the appropriate bulb and socket assemblycounter-clockwise, and then pull it out of the hea...

3. Pull the bulb out of the socket assembly. 4. Push the replacement bulb into the socket assembly. 5. Reinstall the bulb and socket assembly into the head-light assembly, and then turn it clockwise. 6. Install the splash shield and push pin. High Intensity Discharge Headlights (HID) The headlights ...

Front Fog Light 1. Remove the push pin from the upper outer corner ofthe splash shield and remove the splash shield. 2. Turn the bulb and socket assembly counter-clockwise,and then pull it out of the front fog light assembly. 3. Pull the bulb out of the socket assembly. 4. Push the replacement bulb ...

Taillight, Tail/Stop Light, Rear Marker Light 1. Open the trunk 2. Remove the two fasteners and then remove the accesspanel. 3. Turn the appropriate bulb and socket assemblycounter-clockwise, and then pull it out of the upper lightassembly. 4. Pull the bulb out of the socket assembly. 1 — Rear Marke...

5. Push the replacement bulb into the socket assembly. 6. Reinstall the bulb and socket assembly into the upperlight assembly, and then turn it clockwise. 7. Install the access panel and the two fasteners. 8. Close the trunk. Backup Light, Rear Turn Signal Light 1. Open the trunk. 2. Remove the two ...

3. Remove the three upper light assembly retaining nuts. 4. Remove the three bulb and socket assemblies from theupper light assembly by turning them counter-clockwiseand then pulling them out of the upper light assembly. MAINTAINING YOUR VEHICLE 247 7

License Light 1. Open the trunk. 2. Turn the bulb and socket assembly counter-clockwise,and then pull it out of the housing. 3. Pull the bulb out of the socket assembly. 4. Push the replacement bulb into the socket assembly. 5. Reinstall the bulb and socket assembly into the hous-ing, and then turn ...

HEADLIGHT AIMING The headlights on your new vehicle were aimed at thefactory under a no load setting. A great increase in weightwill change the aiming of the headlights. Therefore, itmay be necessary to readjust the headlights if youtypically carry an excessive amount of weight in the rearcompartmen...

MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance . . . . . . . . 256 m Maintenance Schedules . . . . . . . . . . . . . . . . . . . 256 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 259 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . . 269 8 M A I N T...

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in boldtype must be done at the times or mileages specified to assure the continued proper functioning of the emissioncontrol system. These, and all other maintenance servicesincluded in this manual, should be done to p...

• Off-road or desert operation. • If equipped for and operating with E-85 (ethanol)fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5000 km) or 3 months,whichever comes first, and follow the maintenance rec-ommendations in Schedule “B” in this section. NOTE: If...

SCHEDULE “B” Follow schedule “B” if you usually operate your vehicleunder one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. • Short trips of less than 10 miles (16 km). • More ...

Miles 3,000 6,000 9,000 12,000 15,000 18,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) (30 000) Change engine oil and engine oil filter, if notreplaced at 3 months. X X X X X X Rotate the tires. LL X X X Inspect and replace the air cleaner filter ifnecessary. X Inspect the transmissio...

Miles 93,000 96,000 99,000 102,000 105,000 108,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) (180 000) Change engine oil and engine oil filter, if notreplaced at 3 months. X X X X X X Rotate the tires. LL X X X Inspect and replace the engine air cleaner fil-ter if necessary. X R...

Miles 93,000 96,000 99,000 102,000 105,000 108,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) (180 000) Inspect the brake linings. X X Change the rear axle fluid. X X Change the brake and clutch fluid. X Change the brake fluid. X Lubricate the front and rear suspension balljoints...

Miles 111,000 114,000 117,000 120,000 (Kilometers) (185 000) (190 000) (195 000) (200 000) Change engine oil and engine oil filter, if not replacedat 3 months. X X X X Rotate the tires. LL X X Inspect and replace the engine air cleaner filter if neces-sary. X Inspect and replace the PCV valve if nec...

Miles 111,000 114,000 117,000 120,000 (Kilometers) (185 000) (190 000) (195 000) (200 000) Change the brake and clutch fluid. X Lubricate the front and rear suspension ball joints. X ‡ This maintenance is not required if previously replaced. LL Although not required, the manufacturer recom- mends re...

Miles 96,000 102,000 108,000 114,000 120,000 (Kilometers) (160 000) (170 000) (180 000) (190 000) (200 000) [Months] [96] [102] [108] [114] [120] Change engine oil and engine oil filter. X X X X X Rotate the tires. LL X X X X X Inspect and replace the engine air cleaner filter ifnecessary. X Inspect...

IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service ForYour Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . 277 ▫ Prepare For The Appointment . . . . . . . . . . . . 277 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 277 ▫ Be Reasonable With Req...

special tools, and the latest information to assure yourvehicle is fixed correctly and in a timely manner. This is why you should always talk to your authorizeddealer’s service manager first. Most matters can be re-solved with this process. • If for some reason you are still not satisfied, talk to t...

Customer Assistance For The Hearing Or SpeechImpaired (TDD/TTY) To assist customers who have hearing difficulties, themanufacturer has installed special TDD (Telecommuni-cation Devices for the Deaf) equipment at its CustomerCenter. Any hearing or speech impaired customer whohas access to a TDD or a ...

PUBLICATION ORDER FORMS To order the following manuals, you may use either thewebsite or the phone numbers listed below. Visa, Mas-tercard, American Express, and Discover orders are ac-cepted. If you prefer mailing your payment, please callfor an order form. NOTE: A street address is required when o...

Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Or Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals DEPARTMENT OF TRANSPORTATION UNIFORMTIRE QUALITY GRADES The following describes the tire grading categories estab-lished...

on specified government test surfaces of asphalt andconcrete. A tire marked C may have poor traction perfor-mance. WARNING! The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does notinclude acceleration, cornering, hydroplaning, orpeak traction characteri...

Hazard Driving Through Flowing, Rising, orShallow Standing Water . . . . . . . . . . . . . . . . . 140 Hazard Warning Flasher . . . . . . . . . . . . . . . . . 99,176Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . 81,243 Aiming . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Key-In Reminder . . . . . . . . . . . . . . . . . . . . . . . . . 13Keyless Entry System . . . . . . . . . . . . . . . . . . . . . . 17Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Knee Bolster . . . . . . . . . . . . . . . . . . . . . . . . . . 40,41 Lane Change and Turn...

Remote Keyless Entry (RKE) . . . . . . . . . . . . . . . . . 17Remote Trunk Release . . . . . . . . . . . . . . . . . . . . . 29Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 197Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . 162Reporting Safety Defects . . . . . . ....

Tire Safety Information . . . . . . . . . . . . . . . . . . . . 149TIREFIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59,157,283 Aging (Life of Tires) . . . . . . . . . . . . . . . . . . . . 162Air Pressure . . . . . ....

V i p e r O W N E R ’ S M A N U A L 2 0 0 8 2 0 0 8V ip e r 81-226-0804 Second Edition Printed in U.S.A.