Dodge 2004 Neon SRT4 - Manuals

A WORD ABOUT YOUR KEYS The dealer that sold you your new vehicle has the keycode numbers for your vehicle locks. These numbers canbe used to order duplicate keys from your dealer. Askyour dealer for these numbers and keep them in a safeplace. The double sided keysmay be inserted into thelocks with e...

immediately after the ignition switch is turned on for abulb check. Afterwards, if the bulb remains on, thisindicates a problem with the electronics. If the bulb begins to flash after the bulb check, thisindicates that an invalid key has been used to start thevehicle. Both of these conditions will r...

consists of programming a blank key to the vehicleelectronics. A blank key is one which has never beenprogrammed. NOTE: When having the Sentry Key Immobilizer System serviced, bring all vehicle keys with you to thedealer. Customer Key Programming You can program new keys to the system if you have tw...

STEERING WHEEL LOCK Your vehicle is equipped with a passive steering wheellock. This lock prevents steering the vehicle without theignition key. If the steering wheel is rotated no more than1/2 turn in either direction and the key is not in theignition switch, the steering wheel will lock. To manual...

WARNING! When leaving the vehicle always remove the keyfrom the ignition lock, and lock your vehicle. Do notleave children unattended in the vehicle, or withaccess to an unlocked vehicle. Unsupervised use ofvehicle equipment may cause severe personal inju-ries and death. Power Door Locks A power doo...

Child-Protection Door Lock System (Rear Doors) To provide a safer environment for children riding in therear seat, the rear doors of your vehicle have the child-protection door lock system. To use the system, open each rear door and slide thecontrol UP to engage the locks and DOWN to disengagethe ch...

INTERNAL EMERGENCY TRUNK LID RELEASE WARNING! Do not allow children to have access to the trunk,either by climbing into the trunk from outside, orthrough the inside of the vehicle. Always close thetrunk lid when your vehicle is unattended. Once inthe trunk, young children may not be able to escape,e...

REMOTE KEYLESS ENTRY This system allows you to lock or unlock the doors andtrunk or activate the panic alarm from distances up toabout 23 feet (7 meters) using a hand held transmitter. NOTE: A slight delay of up to two seconds can occur before the doors or trunk will unlock. To Unlock the Doors Pres...

To Unlock the Trunk Press the TRUNK button on the transmitter twice tounlock the trunk. NOTE: A slight delay of up to two seconds can occur before the trunk unlatches. Using The Panic Alarm To turn on the panic alarm feature, press and release thePANIC button. When the panic alarm is on the headligh...

General Information This device complies with FCC rules part 15. Operation issubject to the following two conditions: (1) This devicemay not cause harmful interference and (2) This devicemust accept any interference that may be received, in-cluding interference that may cause undesired operation. If...

WARNING! • Wearing a seat belt incorrectly is dangerous. Seatbelts are designed to go around the large bones ofyour body. These are the strongest parts of yourbody and can take the forces of a collision thebest. • Wearing your belt in the wrong place could makeyour injuries in a collision much worse...

WARNING! A frayed or torn belt could rip apart in a collisionand leave you with no protection. Inspect the beltsystem periodically, checking for cuts, frays, or looseparts. Damaged parts must be replaced immediately.Do not disassemble or modify the system. Front seatbelt assemblies must be replaced ...

Lap/Shoulder Belt Untwisting Procedure Use the following procedure to untwist a twisted lap/shoulder belt. 1. Position the latch plate as close as possible to theanchor point. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 2

2. At about 6 to 12 inches above the latch plate, grasp andtwist the belt webbing 180° to create a fold that beginsimmediately above the latch plate. 3. Slide the latch plate upward over the folded webbing.The folded webbing must enter the slot at the top of thelatch plate. 4. Continue to slide the ...

Keep the belt low so that it does not come across theabdomen. That way the strong bones of the hips will takethe force if there is a collision. Seat Belt Extender If a seat belt is too short, even when fully extended andwhen the adjustable upper shoulder belt anchorage (ifequipped) is in its lowest ...

If the vehicle is equipped with side airbags, they arelocated inside the driver and front passenger seats, andtheir covers are also labeled SRS AIRBAG. NOTE: Airbag covers may not be obvious in the interior trim; but they will open to allow airbag deploy-ment. WARNING! • Do not put anything on or ar...

Airbags inflate in moderate to high speed impacts. Alongwith the seat belts, front airbags work with the instru-ment panel knee bolsters to provide improved protectionfor the driver and front passenger. Side airbags also workwith seat belts to improve occupant protection. The seat belts are designed...

• The knee impact bolsters help protect the knees andposition you for the best interaction with the frontairbag. If A Deployment OccursThe airbag system is designed to deploy when the AirbagControl Module detects a moderate-to-severe frontalcollision, to help restrain the driver and front passenger,...

WARNING! Deployed airbags can’t protect you in another colli-sion. Have the airbags replaced by an authorizeddealer as soon as possible. Side Airbag System — If Equipped • The Side Impact Airbag Control Modules determine ifa side collision is severe enough to require the airbagto inflate. The Side I...

the rear seat to install the child restraint. You will easilyfeel them if you run your finger along the intersection ofthe surfaces. The lower strap hooks are passed over thetop of each bar, pushing aside the seat cover material. In addition, there are tether strap anchoragesbehind each rear seating...

Airbag Light The light should come on and remain on for 6 to8 seconds as a bulb check when the ignitionswitch is first turned to ON/RUN. If the bulb is not lit during starting, have it replaced. If the light stayson or comes on while driving, have the system checkedby an authorized dealer. Defroster...

UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .47 ▫ Outside Mirror — Driver’s Side . . . . . . . . . . . .47 ▫ Outside Mirror — Passenger’s Side . . . . . . . . . ....

WARNING! • Adjusting a seat while the vehicle is moving isdangerous. The sudden movement of the seatcould cause you to lose control. The seat beltmight not be properly adjusted and you could beinjured. Adjust the seat only while the vehicle isparked. • Do not ride with the seatback reclined so that ...

Folding Rear Seat To provide additional storage area, the center of each rearseatback can be folded forward. Pull on the loops shownin the picture to fold down either or both seatbacks. WARNING! • It is extremely dangerous to ride in a cargo area,inside or outside of a vehicle. In a collision,people...

TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pullthe hood release lever located under the driver’s side ofthe instrument panel. Then lift the safety catch located under the front edge ofthe hood, near the center and raise the hood. UNDERSTANDING THE FEATURES OF YO...

Use the hood prop rod to secure the hood in the openposition as shown. To prevent possible damage, do notslam the hood to close it. Use a firm downward push atthe center of the hood to ensure that both latches engage. WARNING! If the hood is not fully latched it could fly up whenthe vehicle is movin...

Interior Lights The interior lights come on when a door is opened. The interior lights will automatically turn off in about 8minutes if a door is left open or the dimmer control is leftin the Dome light position. Turn the ignition switch ONto restore the interior light operation. Dimmer Control With...

lights, the passing lights, and fog lights. The lever islocated on the left side of the steering column. Headlights, Parking Lights, Instrument PanelLights Turn the end of the Multi-Function Control Lever to thefirst detent for parking light operation. Turn to thesecond detent for headlight operatio...

TILT STEERING COLUMN To tilt the column, push down on the lever below the turnsignal control and move the wheel up or down, asdesired. Pull the lever back towards you to lock thecolumn firmly in place. WARNING! Tilting the steering column while the vehicle ismoving is dangerous. Without a stable ste...

UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instrument Panel Features . . . . . . . . . . . . . . . .61 m Instrument Cluster—Turbo . . . . . . . . . . . . . . . .62 m Instrument Cluster Descriptions . . . . . . . . . . . .63 m Electronic Digital Clock . . . . . . . . . . . . . . . . . .68 ▫ Clock...

INSTRUMENT PANEL FEATURES UNDERSTANDING YOUR INSTRUMENT PANEL 61 4

INSTRUMENT CLUSTER—TURBO 62 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTER DESCRIPTIONS 1. Fog Light Indicator This light shows when the fog lights are ON. 2. Brake System Warning Light This light monitors various brake functions,including brake fluid level and parking brakeapplication. If the brake light comes on, it may indicate that the parking brake ...

16. Malfunction Indicator Light This light is part of an onboard diagnosticsystem called OBD that monitors engine con-trol systems. The light will illuminate briefly when the key is in the ON/RUN position beforeengine start. If the bulb does not come on whenturning the key from OFF to ON/RUN, have t...

20. Trip IndicatorThis light will illuminate when the Trip Odometer is inuse. 21. Temperature Gauge The temperature gauge shows engine coolanttemperature. Normal operating range should bewithin one notch above or one notchbelow the 200 degree mark. Thegauge pointer may show a higherthan normal tempe...

Electrical Disturbances Radio waves may pick up electrical disturbances duringtransmission. They mainly affect the wave amplitude,and thus remain a part of the AM reception. Theyinterfere very little with the frequency variations thatcarry the FM signal. AM Reception AM sound is based on wave amplit...

You may add a second station to each push-button byrepeating the above procedure with this exception: Pressthe SET button twice and SET 2 will show in the displaywindow. Each button can be set for SET 1 and SET 2 inboth AM and FM. This allows a total of 10 AM and 10 FMstations to be locked into push...

display will show the track number and index time inminutes and seconds. Play will begin at the start of track 1. SeekPress the top of the SEEK button for the next selection onthe CD. Press the bottom of the button to return to thebeginning of the current selection, or return to thebeginning of the ...

CD Changer Operation — If Equipped MODEPress the MODE button to select between the cassettetape player, CD player, and the CD changer (if equipped). Disc/Program Button 1Press the DISC (button 1) button to play the next avail-able disc. Random Play — RND/Program Button 4Press the RND (button 4) butt...

• Driving under wide bridges or along tall buildings cancause intermittent reception. • Placing objects over or too close to the antenna cancause signal blockage. COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take thefollowing precautions: 1. Handle the disc by its edge; avoi...

CLIMATE CONTROLS Air Conditioning The Air Conditioning System allows you to balance thetemperature, amount, and direction of air circulatingthroughout the vehicle. The air conditioning system of your vehicle containsR-134a, a refrigerant that does not deplete the ozone layerin the upper atmosphere. ...

Bi-Level Air is directed through the panel and floor out-lets. NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmerair goes to the floor outlets. This feature gives improvedcomfort during sunny but cool conditions. NOTE: If you choose either th...

NOTE: If your air conditioning performance seems lower than expected, check the front of the A/C con-denser located in front of the radiator, for an accumula-tion of dirt or insects. Clean with a gentle water sprayfrom behind the radiator and through the condenser.Fabric front fascia protectors may ...

Operating Tips UNDERSTANDING YOUR INSTRUMENT PANEL 81 4

Window FoggingVehicle side windows tend to fog on the inside in mildrainy or humid weather. To clear the windows, use theA/C, PANEL and blower controls. Direct the paneloutlets toward the side windows. Do not use recirculatewithout A/C for long periods as fogging may occur. Interior fogging on the w...

ELECTRIC REAR WINDOW DEFROSTER A push-button at the center of the instrumentpanel, below the radio, turns the defroster ON or OFF. An amber light shows that the defroster is on. NOTE: The defroster turns off automatically after 10 minutes of operation. Each following activation of thedefroster will ...

STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . .87 ▫ Manual Transaxle . . . . . . . . . . . . . . . . . . . . . .87 ▫ Normal Starting . . . . . . . . . . . . . . . . . . . . . . .87 ▫ Starting In Cold Weather(Below 32°F Or 0°C) . . . . . . . . . . . . ....

STARTING PROCEDURES Before starting your vehicle, adjust your seat, adjust bothinside and outside mirrors, and fasten your seat belts. CAUTION! Long periods of engine idling, especially at highengine speeds can cause excessive exhaust tempera-tures which can damage your vehicle. Do not leaveyour veh...

If the engine fails to start within 15 seconds, turn the keyOFF wait 10 to 15 seconds, then repeat the normalstarting procedure. WARNING! Do not attempt to push or tow your vehicle to get itstarted. Unburned fuel could enter the catalyticconverter and once the engine has started, ignite anddamage th...

CAUTION! To prevent damage to the starter, do not crank theengine for more than 15 seconds at a time. Wait 10 to15 seconds before trying again. After Starting The idle speed will automatically decrease as the enginewarms up. Turbocharger “Cool Down” NOTE: Letting the engine idle after severe operati...

MANUAL TRANSAXLE NOTE: The parking brake should be engaged and the gear selector placed in REVERSE before leaving thevehicle, especially on an incline. NOTE: Clutch must be depressed for engine to start. Fully depress the clutch pedal before you shift gears. Asyou release the clutch pedal, lightly d...

Never drive with your foot resting on the clutch pedal, ortry to hold the vehicle on a hill with the clutch pedalpartially engaged. This will cause abnormal wear on theclutch. Never shift into REVERSE until the vehicle has come to acomplete stop. NOTE: During cold weather, until the transaxle lubri-...

If you exceed these speeds, you may notice the engine cutin and out. This is caused by an electronic limiter in theengine computer. The engine will run normally whenyou reduce engine speed. Downshifting Proper downshifting may improve fuel economy andprolong engine life. CAUTION! If you skip more th...

BRAKE SYSTEM Your vehicle is equipped with power assisted brakes asstandard equipment. In the event power assist is lost forany reason (for example, repeated brake applicationswith the engine off), the brakes will still function. Theeffort required to brake the vehicle will be much greaterthan that ...

WARNING! • Anti-lock system (ABS) cannot prevent the natu-ral laws of physics from acting on the vehicle, norcan it increase braking or steering efficiency be-yond that afforded by the condition of the vehiclebrakes and tires or the traction afforded. • The ABS cannot prevent accidents, includingtho...

TIRE SAFETY INFORMATION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. designstandards. P-Metric tires have the letter “P” moldedinto the sidewall preceding the size designation. Ex-ample: P215/65R15 95H. • European Metric tire sizing is based on Europeandesign standards. Tir...

Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ( ....blank.... ( = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standardsT = Temporary Spare tire31 = Overall Diameter in Inches (in)215 = Sect...

EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load correspondingto its load index under certain operating conditions.—The maximum speed correspon...

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tirehowever the date code may only be on one side. Tireswith white sidewalls will have the full TIN includingdate code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black side...

Tire Loading and Tire Pressure Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Infor- mation” placard located on the driver’s side “B” pillar. Tire and Loading Information Placard This placard tells you important information aboutthe,1) number of people that can be carried in the ...

2. Economy—Improper inflation pressures can cause uneven wearpatterns to develop across the tire tread. These abnormalwear patterns will reduce tread life resulting in a need forearlier tire replacement. Underinflation also increases tirerolling resistance and results in higher fuel consumption. 3. ...

WARNING! High speed driving with your vehicle under maxi-mum load is dangerous. The added strain on yourtires could cause them to fail. You could have aserious accident. Don’t drive a vehicle loaded to themaximum capacity at continuous speeds above 75mph (120 km/h). Radial-Ply Tires WARNING! Combini...

CAUTION! Because of the reduced ground clearance, do not takeyour vehicle through an automatic car wash with thecompact spare installed. Damage to the vehicle mayresult. Tire Spinning When stuck in mud, sand, snow, or ice conditions, do notspin your vehicle’s wheels above 35 mph (55 km/h). See the p...

WARNING! • Do not use a tire, wheel size or rating other thanthat specified for your vehicle. Some combina-tions of unapproved tires and wheels may changesuspension dimensions and performance charac-teristics, resulting in changes to steering, han-dling, and braking of your vehicle. This can causeun...

Snow tires may have a lower speed rating than factoryequipped tires and may not match the maximum vehiclespeed. Snow tires generally have lower speed ratings than whatwas originally equipped with your vehicle and shouldnot be operated at sustained speeds over 75 mph (120km/h). Tire Rotation Recommen...

ADDING FUEL NOTE: The fuel tank filler tube has a restricting door about 2 inches (50 mm) down from the opening. If fuel ispoured from a portable container, the container shouldhave a flexible nozzle long enough to force open therestricting door. Fuel Tank Filler Cap The gas cap is behind the fuel f...

WARNING! • Remove the fuel tank filler tube cap (gas cap)slowly to prevent fuel spray from the filler neckwhich may cause injury. • The volatility of some gasolines may cause a buildup of pressure in the fuel tank that may increasewhile you drive. This pressure can result in aspray of gasoline and/o...

WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . 120 m If Your Engine Overheats . . . . . . . . . . . . . . . . 120 m Jacking And Tire Changing . . . . . . . . . . . . . . . 122 ▫ Preparations For Jacking . . . . . . . . . . . . . . . . 122 ▫ Instructions...

HAZARD WARNING FLASHER The flasher switch is on top of the steering column,just behind the steering wheel. Depress the switch and both cluster indicators and all front and rear direc-tional signals will flash. Depress the switch again to turnHazard Warning Flashers off. Do not use this emergency war...

JACKING AND TIRE CHANGING WARNING! • Getting under a jacked-up vehicle is dangerous.The vehicle could slip off the jack and fall on you.You could be crushed. Never get any part of yourbody under a vehicle that is on a jack. Never startor run the engine while the vehicle is on a jack. Ifyou need to g...

Do not raise the vehicle until you are sure the jack issecurely engaged. 4. Raise the vehicle by turning the jack screw to the right.Raise the vehicle only until the tire clears the surface.Miminum tire lift provides maximum vehicle stability. WARNING! Raising the vehicle higher than necessary can m...

WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirtingout the battery vent; 2. Personal injury or property damage due to batteryexplosion; 3. Damage to charging system of booster vehicle orof immobilized vehicle. DRIVING ON SLIPPERY SURFACES Accel...

4. Keep tires properly inflated. 5. Maintain enough distance between your vehicle andthe vehicle in front of you to avoid a collision in a suddenstop. FREEING A STUCK VEHICLE If your vehicle becomes stuck in mud, sand or snow, itcan often be moved by a rocking motion. Turn yoursteering wheel right a...

MAINTAINING YOUR VEHICLE CONTENTS m 2.4L Turbo Charged Engine Compartment . . . . 133 m Onboard Diagnostic System — OBD II . . . . . . 134 m Emissions Inspection And MaintenancePrograms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134 m Replacement Parts . . . . . . . . . . . . . . . . . ...

2.4L TURBO CHARGED ENGINE COMPARTMENT MAINTAINING YOUR VEHICLE 133 7

ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboarddiagnostic system called OBD II. This system monitorsthe performance of the emissions, and engine controlsystems. When these systems are operating properly,your vehicle will provide excellent performance and fuel...

Normally, the OBD system will be ready. The OBDsystem may not be ready if your vehicle was recentlyserviced, if you recently had a dead battery, or a batteryreplacement. If the OBD system should be determinednot ready for the I/M test, your vehicle may fail the test. Your vehicle has a simple igniti...

vehicle serviced before going to the I/M station. The I/Mstation can fail your vehicle because the MIL symbol is onwith the engine running. REPLACEMENT PARTS Use of genuine Mopar parts for normal/scheduled main-tenance and repairs is highly recommended to insure thedesigned performance. Damage or fa...

Engine Oil Checking Oil LevelTo assure proper engine lubrication, the engine oil mustbe maintained at the correct level. Check the oil level atregular intervals, such as every fuel stop. The best time to check the engine oil level is about 5minutes after a fully warmed engine is shut off, or befores...

the requirements of DaimlerChrysler Material StandardMS-6395. Use Mopar or an equivalent oil meeting thespecification MS-6395. The manufacturer recommends the use of Mobil 1 t 10W30 synthetic engine oil. American Petroleum Institute (API) Engine OilIdentification Symbol This symbol means that the oi...

CAUTION! It is essential when replacing the cables on thebattery that the positive cable is attached to thepositive post and the negative cable is attached to thenegative post. Battery posts are marked positive (+)and negative (-) and identified on the battery case.Cable clamps should be tight on th...

Power Steering Fluid Check Checking the power steering fluid level at a definedservice interval is not required. The fluid should only bechecked if a leak is suspected, abnormal noises areapparent, and/or the system is not functioning as antici-pated. Coordinate inspection efforts through a certifie...

Windshield Wiper Blades Clean the rubber edges of the wiper blades and thewindshield periodically with a sponge or soft cloth and amild non abrasive cleaner, or use the washer solvent. Thiswill remove accumulations of salt or road film and helpreduce streaking and smearing. Operation of the wipers o...

Cooling System WARNING! • When working near the radiator cooling fan, dis-connect the fan motor lead or turn the ignition keyto the OFF position. The fan is temperature con-trolled and can start at any time the ignition key isin the ON position. • You or others can be badly burned by hot coolantor s...

Adding CoolantWhen adding coolant, a minimum solution of 50% eth-ylene glycol antifreeze coolant in water should be used.Use higher concentrations (not to exceed 70%) if tempera-tures below –34°F (-37°C) are anticipated. Use only high purity water such as distilled or deionizedwater when mixing the ...

The radiator normally remains completely full, so there isno need to remove the radiator cap unless checking forcoolant freeze point or replacing coolant. Advise yourservice attendant of this. As long as the engine operatingtemperature is satisfactory, the coolant bottle need onlybe checked once a m...

E. Make sure that the radiator and coolant bottle hosesare not kinked or obstructed. F. Keep the front of the radiator and air conditioningcondenser clean. G. Do not change the thermostat for summer or winteroperation. If replacement is ever necessary, install ONLYthe correct type thermostat. Other ...

Brake System In order to assure brake system performance, all brakesystem components should be inspected periodically.Suggested service intervals can be found in the Mainte-nance Section. WARNING! Riding the brakes can lead to brake failure andpossibly an accident. Driving with your foot restingor r...

hot or cold weather and other extreme conditions willhave an adverse effect on paint, metal trim, and under-body protection. The following maintenance recommendations will enableyou to obtain maximum benefit from the corrosionresistance built into your vehicle. What Causes Corrosion?Corrosion is the...

Special Care • If you drive on salted or dusty roads or if you drivenear the ocean, hose off the undercarriage at least oncea month. • It is important that the drain holes in the lower edgesof the doors, rocker panels and rear deck lid be keptclear and open. • If you detect any stone chips or scratc...

Interior Fuses The fuse access panel is behind the end cover at the leftside of the instrument panel. To remove the panel, pull itout, as shown. A diagram identifying the componentsand circuits is located on the inside of the cover. CAUTION! When replacing a blown fuse, it is important to useonly a ...

BULB REPLACEMENT Headlight Bulb Replacement CAUTION! Do not touch the new headlight bulb with yourfingers. Oil contamination will severely shortenbulb life. 1. Remove the three upper fascia screws. 2. Remove two screws from the headlight assembly andremove the assembly from the vehicle. NOTE: The he...

Front Park/Turn Signal Lights 1. Remove the headlight assembly 2. Twist the bulb socket 1/4 turn and remove. 3. Pull the bulb from the socket and replace. Front Sidemarker Light 1. Remove the screws and push-pins from the frontfender splash shield. 2. Reach between the fender and the splash shield, ...

FLUID CAPACITIES U.S. Metric Fuel (Approximate) 12.5 Gallons 47.5 Liters Engine Oil 2.4 Liter Turbo Charged Engines 5.0 qts 4.8 Liters Cooling System * 2.4 Liter Turbo Charged Engines 8.1 qts 7.7 Liters * Includes heater and coolant recovery bottle filled to MAX level. MAINTAINING YOUR VEHICLE 165 7

MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance . . . . . . 168 m Maintenance Schedule . . . . . . . . . . . . . . . . . . 168 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 171 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . . 178 8 M A I N TE N A N...

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in boldtype must be done at the times or mileages specified to assure the continued proper functioning of the emissioncontrol system. These, and all other maintenance servicesincluded in this manual, should be done to p...

NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months,whichever comes first and follow schedule “B” of the 9 Maintenance Schedules 9 section of this manual. NOTE: Most vehicles are operated under the conditions listed for Schedule 9 B 9 . Second is S...

Miles 3,000 6,000 9,000 12,000 15,000 18,000 (Kilometers) (5 000) (10 000) (14 000) (19 000) (24 000) (29 000) Change engine oil and engine oil filter. X X X X X X Inspect the brake linings. X Inspect the engine air cleaner filter. Replaceas necessary.* X Inspect and replace, if required, the make-u...

IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For YourVehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184 ▫ Prepare For The Appointment . . . . . . . . . . . . 184 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 184 ▫ Be Reasonable ...

Service ContractYou may have purchased a service contract for yourvehicle to help protect you from the high cost of unex-pected repairs after your manufacturer’s new vehiclelimited warranty expires. The manufacturer stands be-hind only the manufacturer’s Service Contracts. If youpurchased a manufact...

MOPAR T PARTS Mopar t fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep yourvehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If youbelieve that your vehicle has a defect which could causea crash or c...

PUBLICATION ORDER FORMS To order the following manuals, you may use either thewebsite or the phone numbers listed below. Visa, Mas-tercard, American Express, and Discover orders are ac-cepted. If you prefer mailing your payment, please callfor an order form. NOTE: A street address is required when o...

Temperature Grades The temperature grades are A (highest), B, and C, repre-senting the tire’s resistance to the generation of heat andits ability to dissipate heat when tested under controlledconditions on a specified indoor laboratory test wheel.Sustained high temperature can cause the material of ...

ABS (Anti-Lock Brake) System . . . . . . . . . . . . . . 94Adding Engine Coolant (Antifreeze) . . . . . . . . . 150Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 116Air Cleaner, Engine . . . . . . . . . . . . . . . . . . . . . 142Air Conditioning . . . . . . . . . . . . . . . . . ...