Dodge 2004 Grand Caravan - Manuals

VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehiclecould seriously affect its roadworthiness and safetyand may lead to an accident resulting in seriousinjury or death. INTRODUCTION 7 1

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS m A Word About Your Keys . . . . . . . . . . . . . . . . . .12 ▫ Ignition Key Removal . . . . . . . . . . . . . . . . . . .12 ▫ Key-In-Ignition Reminder . . . . . . . . . . . . . . . .13 m Sentry Key . . . . . . . . . . . . . . . . . . . . . . . ....

NOTE: The power window switches, radio, power outlets, and removable console (if equipped), will remainactive for up to 45 seconds after the ignition switch hasbeen turned off. Opening a vehicle front door will cancelthis feature. WARNING! Leaving children in a vehicle unattended is danger-ous for a...

chip (transponder) embedded into them. Only keys thathave been programmed to the vehicle can be used to startand operate the vehicle. The Sentry Key Immobilizer System does not need to bearmed or activated. Operation of the system is automaticregardless of whether or not the vehicle is locked orunlo...

All of the keys provided with your new vehicle havebeen programmed to the vehicle electronics. Replacement Keys NOTE: Only keys that have been programmed to the vehicle electronics can be used to start the vehicle. Oncea Sentry Key has been programmed to a vehicle, it cannot be programmed to any oth...

4. Insert a blank Sentry Key into the ignition switch andturn the ignition switch ON within 60 seconds. After 10seconds a single chime will sound. The Theft Alarm Lightwill stop flashing, turn on for 3 seconds; then turn off. The new Sentry Key has been programmed. The KeylessEntry Transmitter will ...

WARNING! • For personal security and safety in the event of anaccident, lock the vehicle doors as you drive aswell as when you park and leave the vehicle. • When leaving the vehicle always remove the keyfrom the ignition lock, and lock your vehicle. Donot leave children unattended in the vehicle, or...

If you press the power door lock switch while the slidingdoor is open, the sliding door will lock. Automatic Door Locks — If EquippedThe doors will lock automatically on vehicles with powerdoor locks if: 1. The transmission is in gear, 2. all doors are closed, 3. the vehicle speed is above 18 mph (2...

4. any door is opened (excluding liftgate) and 5. the vehicle speed is 0 mph (0 km/h). The Auto Unlock feature can be enabled or disabled byperforming the procedure in the Overhead Console,Customer Programmable Features section. NOTE: Use the Auto Door Locks and Auto Unlock features in accordance wi...

To unlock the doors and liftgate: Press and release the UNLOCK button on the transmitteronce to unlock the driver’s door side of the vehicle, ortwice to unlock all doors and liftgate. The illuminatedentry system also turns on. NOTE: If desired, the “Remote Unlock Driver’s Door 1st” feature can be tu...

headlights and park lights will flash, the horn will pulseon and off and the interior lights will turn on. The panic alarm will stay on for 3 minutes unless youturn it off by pressing the PANIC button a second time orby turning the ignition switch to the ON position. NOTE: When you turn off the pani...

General Information This device complies with part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions: • This device may not cause harmful interference. • This device must accept any interference received,including interference that may cause undesired...

2. Remove and replace the batteries. Avoid touching thenew batteries with your fingers. Skin oils may causebattery deterioration. If you touch a battery, clean it withrubbing alcohol. 3. To reassemble the transmitter case snap two halvestogether. Make sure there is an even “gap” between thetwo halve...

exterior lights will flash, the horn will sound, and theignition will not start the vehicle. If this occurs, disarmthe system. SLIDING SIDE DOOR The sliding door may be opened from the inside or theoutside. Pull out on the outside handle to open thesliding door from the outside. To open the sliding ...

• Avoid high impacts against the door stop when open-ing the door. This is very important when your vehicleis parked on an incline as the door will slide faster inthe downhill direction. • There is a hold-open latch that is activated when thesliding door is fully opened. This latch will keep yoursli...

Child Protection Door Lock To provide a safer environment for small children ridingin the rear seats, the sliding doors are equipped with achild protection door lock system. WARNING! To avoid trapping anyone in the vehicle in a colli-sion. Remember that the sliding doors can only beopened from the o...

door, regardless of the child lock lever position. To avoidunintentional operation of the power sliding door from therear seats, press the button located in the overhead consoleto disable the switches for the rear seat passengers. NOTE: • The power sliding door switches will not operate if thevehicl...

If the liftgate is locked and is not equipped with apowered liftgate, pressing the button on the remotekeyless entry transmitter will result in the liftgate becom-ing unlocked for 30 seconds allowing you to manuallyaccess the liftgate area. NOTE: On vehicles without power locks, the liftgate can onl...

Power Windows — If Equipped You can control either front window using switches onthe driver’s door trim panel. There is a single switch onthe passenger’s door trim panel which operates thepassenger door window. The switches will operate onlywhen the ignition switch is in the ON or ACCESSORYposition....

The power window switches remain active for up to 45seconds after the ignition switch has been turned off.Opening a vehicle front door will cancel this feature. Wind BuffetingWind buffeting can be described as the perception ofpressure on the ears or a helicopter type sound in theears. Your vehicle ...

Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back andadjust the seat. 2. The seat belt latch plate is near the seatback of thefront seats and next to your arm in the rear seats. Graspthe latch plate and pull out the belt. Slide the latch plateup the webbing a...

As a guide, if you are shorter than average, you willprefer a lower position, and if you are taller than average,you’ll prefer a higher position. When you release theanchorage, try to move it up or down to make sure thatit is locked in position. Lap/Shoulder Belt Untwisting Procedure Use the followi...

Center Lap Belts The center seating positions have a lap belt only. To fastenthe lap belt, slide the latch plate into the buckle until youhear a “click”. To lengthen the lap belt, tilt the latch plateand pull. To remove slack, pull the loose end of thewebbing. Wear the lap belt snug against the hips...

NOTE: The front airbags are certified to the Federal regulations that allow less forceful deployment in lowspeed collisions. The front airbags have a multi stage inflator design. Thisallows the airbag to have different rates of inflation thatare based on collision severity. If the vehicle is equippe...

WARNING! • Relying on the airbags alone could lead to moresevere injuries in a collision. The airbags workwith your seat belt to restrain you properly. Insome collisions the airbags won’t deploy at all.Always wear your seat belts even though youhave airbags. • Being too close to the steering wheel o...

How The Front Airbag System Works • The front airbag control module determines if a frontalimpact is severe enough to require the front airbags toinflate. Based on the level of collision severity, the frontairbag control module determines the proper rate ofinflation. The front airbag inflators are d...

• When the front airbag control module detects a colli-sion requiring the front airbags, it signals the inflatorunits. A large quantity of nontoxic gas is generated toinflate the front airbags. Different front airbag inflationrates are possible, these rates are determined by thefront airbag control ...

The front airbag control module also monitors the readi-ness of the electronic parts of the system whenever theignition switch is in the START or ON positions. Theseinclude all of the items listed above except the kneebolster, instrument panel and the steering wheel andcolumn. If the key is in the O...

Maintaining Your Airbag System WARNING! • Modifications to any part of the airbag systemcould cause it to fail when you need it. You couldbe injured because the airbags are not there toprotect you. Do not modify the components orwiring, including adding any kind of badges orstickers to the steering ...

DaimlerChrysler Corporation Integrated ChildSeat — If Equipped Operating instructions for this seat are included with theseat. If the instructions are not with the seat or in theOwner’s Manual Package, replacement instructions canbe obtained. To obtain Integrated Child Seat replacementinstructions:U...

In general, you will first loosen the adjusters on the lowerstraps and tether straps so that you can more easily attachthe hook or connector to the lower anchorages and tetheranchorages. Then tighten all three straps as you push thechild restraint rearward and downward into the seat. Not all child r...

Restraining Infants and Small Children with SeatDelete Feature (Commercial Vehicles Only) There are different sizes and types of restraints forchildren from newborn size to the child almost largeenough for an adult safety belt. Use the restraint that iscorrect for your child: • The rearward-facing i...

WARNING! The vehicle tether anchor is designed to be usedwith a child restraint only. It should not be used forany other purpose. Before use inspect the tetheranchor strap for nicks, abrasions, discoloration, andloose threads. If these or any other condition thatmight effect the performance of the s...

UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS m Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . . .77 ▫ Automatic Dimming Mirror — If Equipped . . . .77 ▫ Driver’s Side Outside Mirror AutoDimmer — If Equipped . . ....

▫ Manual Reclining Seats — If Equipped . . . . . . .83 ▫ Manual Lumbar — If Equipped . . . . . . . . . . . .84 ▫ Middle Rear Bench Seat Recline — IfEquipped . . . . . . . . . . . . . . . . . . . . . . . . . . . .84 ▫ Middle Quad Fold & Tumble Seating . . . . . . . .85 ▫ Middle Quad Fold & Tu...

WARNING! Vehicles and other objects seen in the right sideconvex mirror will look smaller and farther awaythan they really are. Relying too much on your rightside mirror could cause you to collide with anothervehicle or other object. Use your inside mirror when judging the size ordistance of a vehic...

Manual Reclining Seats — If Equipped The recliner mechanism control is on the outboard side ofthe seat. To recline, lean forward slightly, lift the lever,then push back to the desired position and release thelever. Lean forward and lift the lever to return the seatback to its normal position. Using ...

Middle Quad Fold & Tumble Seating The passenger’s and driver’s side middle quad seats canbe tilted forward for easy access to the third seat or rearcargo area. To tilt the seat, pull up on the release handle and tilt theseat fully forward. To return the seat, lower the seat andensure that it is ...

WARNING! In the event of a collision you could be injured if theseat is not fully latched. Middle Quad Fold & Tumble Seat Removal 1. Remove any obstructions from the floor in front of theseat. 2. Lower the head restraint to its full downward positionand ensure that the cupholder is closed. 3. Pu...

lever to return the seatback to its full upright position.Ensure that the seatback is fully latched in the uprightposition. WARNING! In a collision, you or others in your vehicle could beinjured if seats are not properly latched to their floorattachments. Always be sure the seats are fullylatched. 2...

WARNING! If not properly latched, the bench seats could be-come loose. Personal injuries could result. Afterreinstalling these seats, be sure the red indicatorbutton on the release handles return into thehandles. Plastic Grocery Bag Retainer Retainer hooks which will hold plastic grocery baghandles ...

4. Auxiliary Seating—The middle quad seats are removed from the vehicle. The3– passenger bench seat can be installed in either thesecond or third row. Rear Quad and 50/50 Seating Flexibility The seats may be used with either or both seatbacksfolded forward for additional storage space, or witheither...

NOTE:Driving with the 2nd-row seats in the tumbled position isnot recommended when passengers occupy the 3rd rowseats. This position is intended only to increase availablecargo area without requiring removal of the seats.Do not leave the head restraint stored between thecushions for extended periods...

WARNING! • Not all head restraints in this vehicle are the same.Head restraints from one seating position shouldnot be removed and installed in any other seatingposition. In a collision, serious injury or death mayresult if the proper head restraint is not installed oneach seat. • The cargo area in ...

LIGHTS All of the lights, except the hazard warning lights, arecontrolled by switches to the left of the steering columnon the instrument panel. Interior Lights Interior lights are turned on when a door or liftgate isopened, the keyless entry transmitter is activated, orwhen the dimmer control is mo...

NOTE: The key must be out of the ignition switch or the ignition switch must be in the OFF position for thisfeature to operate. Park Lights Turn this switch to the first detent to turn the parklights on. This also turns on all instrument panel lighting. Headlights Turn the headlight switch to the 2n...

Interior light Defeat (OFF) Rotate the dimmer control to theOFF position (extreme bottom).The interior lights will remain offwhen the doors or liftgate areopen. Parade Mode (Daytime Brightness Feature) Rotate the dimmer control to thefirst detent. This feature brightensthe odometer, radio and overhe...

NOTE: The lights must be turned off within 45 seconds of turning the ignition off to activate this feature Front Fog Lights — If Equipped To activate the front fog lights, turn on the parklights or the low beam headlights and pull out onthe headlight switch control knob. An indicator in the headligh...

Turn Signal WarningIf the vehicle electronics sense that the vehicle has traveledat over 18 mph (29 km/h) for about one mile with the turnsignals on, a chime will sound to alert the driver. Headlight Low/High Beam Selector Switch Pull the multifunction lever toward the steering wheel toswitch the he...

a maximum of 20 seconds or until the lever is released. Ifanother washer cycle is desired the end of the lever mustbe pressed again to get another 20 second washer cycle. Ifthe lever is depressed while in the delay range, thewipers will operate for several seconds after the lever isreleased, and the...

WARNING! Tilting the steering column while the vehicle ismoving is dangerous. Without a stable steering col-umn, you could lose control of the vehicle and havean accident. Adjust the column only while the ve-hicle is stopped. Be sure it is locked before driving. TRACTION CONTROL SWITCH — IF EQUIPPED...

To turn the system back ON, press the switch a secondtime until the TRAC OFF indicator turns OFF. NOTE: • The Traction Control System indicator comes on eachtime the ignition switch is turned ON. This will occureven if you used the switch to turn the system OFF. • The Traction Control will make buzz...

• The pedals cannot be adjusted when the vehicle is in R(Reverse) or when the Speed Control System is ON.The following messages will be displayed on vehiclesequipped with the Electronic Vehicle Information Sys-tem (EVIC) if the pedals are attempted to be adjustedwhen the system is locked out (“Adjus...

To Activate: Push the “ON/OFF” button once and the CRUISE indi-cator located below the instrument cluster odometer willilluminate showing the electronic speed control system ison. To turn the system OFF, push the “ON/OFF” buttonagain and the system and indicator will turn off. WARNING! Leaving the E...

To Vary the Speed Setting: When the speed control is set, speed can be increased bypressing and holding the “RESUME/ACCEL” button.When the button is released, a new set speed will beestablished. Tapping the “RESUME/ACCEL” button once will resultin a 2 mph (3 km/h) speed increase. Each time the butto...

WARNING! Speed Control can be dangerous where the systemcan’t maintain a constant speed. Your vehicle couldgo too fast for the conditions, and you could losecontrol. An accident could be the result. Don’t useSpeed Control in heavy traffic or on roads that arewinding, icy, snow-covered, or slippery. ...

turns in an area free from large metal or metallic objects,the “CAL” symbol will turn off and the compass willfunction normally. Manual Compass CalibrationIf the compass appears erratic and the “CAL” symboldoes not appear, you must put the compass into theCalibration Mode manually. To put into a Cal...

To set the variance: Turn the ignition switch ON and set the display to Comp/Temp. On vehicles equipped with aCompass/Mini Trip Computer press the RESET buttonfor approximately 5 seconds. On vehicles equipped withCompass/Temp press and hold the C/T and US/Mbuttons for 5 seconds. The “VAR” symbol wil...

NOTE: Tire pressure menu items are available only on vehicles equipped with the Tire Pressure Monitor Sys-tem. Customer Programmable Features — If Equipped Press the “MENU” button until one of the display choicesfollowing appears: LanguageWhen in this display you may select one of five lan-guages fo...

the Tire Pressure Monitor system and the training routineis not performed, training will be cancelled after oneminute or the next time you cycle the ignition key. Seeyour authorized dealer for service and retraining of thesystem. Use Factory SettingsIf “Yes” is selected, all of the customer programm...

30, 60, or 90 seconds, or not remain on. Pressing the“STEP” button when in this display will select 30, 60, 90,or “OFF.” Headlamp On With Wipers (Available with AutoHeadlights Only)When this feature is selected and the headlight switchhas been moved to the “AUTO” position, the engine isrunning and, ...

WARNING! A moving garage door can cause injury to people andpets in the path of the door. People or pets could beseriously or fatally injured. Only use this transceiverwith a garage door opener that has a “stop andreverse” feature as required by federal safety stan-dards. This includes most garage d...

etc.). For convenience, the hand-held transmitter of thedevice may also be used at any time. In the event thatthere are still programming difficulties or questions,contact HomeLink at: www.homelink.com or 1-800-355-3515 . Erasing HomeLink Buttons To erase programming from the three buttons (individu...

This device complies with part 15 of FCC rules and withRSS-210 of Industry Canada. Operation is subject to thefollowing conditions: • This device may not cause harmful interference. • This device must accept any interference that may bereceived including interference that may cause undes-ired operat...

switch rearward will activate the Express Open Feature,causing the sunroof to open automatically. Press and hold the button located to the right of thesunroof switch, to open the vent. The sunroof can bestopped at any position between closed and full vent. Toclose the sunroof from the vent position,...

A third outlet is located on the driver’s side, just to therear of the sliding door and is also controlled by theignition switch. The lower and rear outlets will notaccommodate a conventional cigar lighter unit. The outlets include tethered caps labeled with a key orbattery symbol indicating the pow...

into one of the cupholders and then push the arm towardthe container until the container is held stable. There areadjustable positions for the arm so the cupholder canaccommodate a wide variety of container types and sizes,including those with handles. The arms of the cupholdercan be adjusted in or ...

STORAGE Front Seat Storage Bin — If Equipped The storage bin is located under the front passenger’sseat. If equipped with a lock, it can be locked with theignition key. Removable Floor Console — If Equipped The removal floor console has a power outlet, storagetray, light, cell phone holder, tissue h...

forward to engage the front of the console into the floortray. Rapidly push down on the rear of the console withenough force to engage the latch, you should hear thelatch “snap” into place. Pull up on the console to be sureit’s firmly attached. NOTE: When the removable floor console is located betwe...

CAUTION! • Many accessories that can be plugged in drawpower from the vehicle’s battery, even when notin use (i.e. cellular phones, etc.). Eventually, ifplugged in long enough, the vehicle’s battery willdischarge sufficiently to degrade battery lifeand/or prevent engine starting. • Accessories that ...

The liftgate sill plate has a raised line with the statement“Load To This Line”. This line indicates how far rearwardcargo can be placed without interfering with liftgateclosing. Cargo Organizer — If Equipped Long wheel base vehicle with rear air conditioning maybe equipped with a cargo organizer th...

Cargo Organizer removalUnscrew the two plastic fasteners located on the floor ofthe rear of the cargo area and remove the cargo organizerfrom the vehicle. NOTE: The cargo organizer must be removed to take out the third row seat. ROOF LUGGAGE RACK — IF EQUIPPED The crossbars and siderails are designe...

capacity of the vehicle. Be sure the total load of cargoinside the vehicle plus that on the external rack does notexceed the maximum vehicle load capacity. To move the cross bars, press the upper edge of eachcross bar button pass the detent, then move the cross barto the desired position. Once the c...

CAUTION! • To avoid damage to the roof rack and vehicle, donot exceed the maximum roof rack load capacityof 150 lbs (68 kg). Always distribute heavy loadsas evenly as possible and secure the load appro-priately. • Long loads which extend over the windshield,such as wood panels or surfboards, or load...

UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS m Instruments And Controls . . . . . . . . . . . . . . . . . 148 m Base Instrument Cluster . . . . . . . . . . . . . . . . . . 149 m Instrument Cluster With Tach . . . . . . . . . . . . . . 150 m Instrument Cluster Descriptions . . . . . . . . . . . . 151...

▫ Time Button . . . . . . . . . . . . . . . . . . . . . . . . . 186 ▫ Changing Modes . . . . . . . . . . . . . . . . . . . . . . 186 ▫ Removing Discs From The CD Changer . . . . . 187 ▫ CD Changer Operation With The ChangerOff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 m 6 Dis...

INSTRUMENTS AND CONTROLS 148 UNDERSTANDING YOUR INSTRUMENT PANEL

BASE INSTRUMENT CLUSTER UNDERSTANDING YOUR INSTRUMENT PANEL 149 4

INSTRUMENT CLUSTER WITH TACH 150 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTER DESCRIPTIONS 1. Fuel GaugeThe pointer shows the level of fuel in the fuel tank whenthe ignition switch is in the ON position. 2. Low Fuel Light When the fuel level reaches approximately 3.0gallons (11.0 liters) this light will turn on andremain on until fuel is added. 3. Liftgate ...

8. Anti-Lock Light This light monitors the Anti-Lock Brake System.The light will turn on when the ignition switch is turned to the ON position and may stay on for as long asfour seconds. If the ABS light remains on or turns on while driving, itindicates that the Anti-Lock portion of the brake system...

20. Odometer/Trip OdometerThe odometer shows the total distance the vehicle hasbeen driven. U.S. federal regulations require that upon transfer ofvehicle ownership, the seller certify to the purchaser thecorrect mileage that the vehicle has been driven. There-fore, if the odometer reading is changed...

AM Reception AM sound is based on wave amplitude, so AM receptioncan be disrupted by such things as lightning, power linesand neon signs. FM Reception Because FM transmission is based on frequency varia-tions, interference that consists of amplitude variationscan be filtered out, leaving the recepti...

Balance The Balance control adjusts the left-to-right speaker bal-ance. Push in the button and it will pop out. Adjust thebalance and push the button back in. The balance will bedisplayed and continuously updated while the button ispressed. Fade The Fade control provides for balance between the fron...

To Set The Radio Push-button Memory When you are receiving a station that you wish tocommit to push-button memory, press the SET button.SET 1 will show in the display window. Select thepush-button you wish to lock onto this station and pressand release that button. If a station is not selected withi...

Pinch Roller Release If ignition power or the radio ON/OFF switch are turnedoff, the pinch roller will automatically retract to protectthe tape from any damage. When power is restored to thetape player, the pinch roller will automatically reengageand the tape will resume play. Noise Reduction The Do...

If the volume control is ON, the unit will switch fromradio to CD mode and begin to play. The display willshow the track number and index time in minutes andseconds. Play will begin at the start of track one. NOTE: • You may eject a disc with the radio OFF. The ignitionswitch must be in the ON or AC...

FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin tofast forward until FF is released. The RW ( Reverse)button works in a similar manner. Program Button 4 (Random Play) Press this button while the CD is playing to activateRandom Play. This feature plays the tracks on the se-lected disc...

CD Diagnostic IndicatorsWhen driving over a very rough road, the CD player mayskip momentarily. Skipping will not damage the disc orthe player, and play will resume automatically. As a safeguard and to protect your CD player, one of thefollowing warning symbols may appear on your display. A CD HOT s...

General InformationThis radio complies with Part 15 of FCC rules and withRSS-210 of Industry Canada. Operation is subject to thefollowing conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received,including interference that may cause undesire...

show the disc number, the track number, and index timein minutes and seconds. Play will begin at the start oftrack 1. LOAD/ EJT — LoadPress the LOAD/ EJT button and the button with thecorresponding number where the CD is being loaded.After the radio displays “load” insert the CD into theplayer. Radi...

TimePress the TIME button to change the display fromelapsed CD playing time to time of day. SALES CODE RBK—AM/ FM STEREO RADIOWITH CD PLAYER AND CD CHANGERCONTROLS Radio Operation Power/Volume ControlPress the ON/VOL control to turn the radio on. Turn thevolume control clockwise to increase the volu...

ModePress the MODE button repeatedly to select between theCD player, the optional remote CD changer and theSatellite Radio (if equipped). When Satellite Radio (ifequipped) is selected “SA” will appear in your radiodisplay. A CD or tape may remain in the player while in theSatellite mode. TimePress t...

Mode Button Press this button to toggle between radio and cd modes. Program Button 1 Press this button to play the next available disc. Program Button 4 (Random Play) Press this button while the CD is playing to activateRandom Play. This feature plays the selections on thecurrent compact disc in ran...

• If you insert a disc with the ignition ON and the radioOFF, the DVD will automatically be pulled into theDVD changer and the display will show the time ofday. EJECT (EJT) Button If there is a single disc in the changer, press the EJTbutton and the disc will eject. The unit will switch to theradio ...

MENU ButtonThis button only functions in the DVD video mode. Pressthis button once to go to the on-screen menu, press thebutton a second time to go to the main menu. When theDVD is in stop mode, pressing the menu button for 3seconds will display the set-up screen. PAUSE/STOP/ PLAY ButtonThis button ...

Channel ButtonPress this button to select between channel “A” orchannel “B”, or if interference is heard through theheadphones. Remote Control Battery Service • To replace the batteries for the remote control slide thecover rearward. The replacement batteries for the remote control are twoAAA batter...

3. Brightness ButtonChanges the brightness of the screen picture. Operating Instructions — Headphones 1. ON/OFF Button 2. Scan Button 3. Volume Control 4. LED 192 UNDERSTANDING YOUR INSTRUMENT PANEL

Power ButtonPressing the power button will turn the headphonesON/OFF. NOTE: • The headphones will turn off automatically and thered LED will illuminate for approximately 2 minuteswhen the radio or rear audio/video system is turnedoff. • The rear audio/video system must be turned ONbefore sound can b...

Headphone Battery Service • Using a key or similar flat object insert into the slot. • Pry on the release tab to open the cover. • Replace the batteries and reinstall the cover. The replacement batteries for the headphones are threeAAA batteries. General InformationThis device complies with part 15 ...

turned all the way down. To prevent this, you shouldperiodically clean the head with a commercially availableWET cleaning cassette. As preventive maintenance, clean the head about every30 hours of use. If you wait until the head becomes verydirty (noticeably poor sound), it may not be possible torem...

Dual Zone Temperature Control — If EquippedWith the Dual Zone Temperature Control System, eachfront seat occupant can independently control the tem-perature of air coming from the outlets on their side ofthe vehicle. This is accomplished by having a separate temperaturecontrol lever for both the dri...

Panel Mode Air comes from the outlets in the instrument panel. Eachof these outlets can be individually adjusted to direct theflow of air. Moving the air vane knob on the centeroutlets down, will close off the air flow from the center outlets. The thumbwheel next to the outboard outlets canbe rotate...

NOTE: In many temperature lever positions, the bi- level mode is designed to provide cooler air out of thepanel outlets and warmer air from the floor outlets. Floor Mode Air comes from the floor outlets. A slight amount of air isdirected through the defrost and side window demisteroutlets. Mix Mode ...

Defrost Mode Air comes from the windshield and side window demistoutlets. Use this setting when necessary to defrost yourwindshield and side windows. NOTE: For improved safety, the compressor is activated and the recirculation mode is deactivated when Mix or Defrost modes are selected. This is done ...

• If your air conditioning performance seems lower thanexpected, check the A/C air filter and the front of theA/C condenser for an accumulation of dirt or insects.The A/C condenser is located in front of the radiator.The A/C air filter is located under the instrumentpanel on the passenger side. • Fa...

Manual Rear Zone Climate Control — If Equipped The Manual Rear Zone Climate Control system has floorair outlets to the rear of the right side sliding door andoverhead outlets at each outboard rear seating position.The unit provides warm or cool air through the floor andupper outlets. The rear blower...

Defrost Mode Air comes from the windshield and side window demistoutlets. Use this setting when necessary to defrost yourwindshield and side windows. Depress the “A/C” button to turn on and off theair conditioning during manual operation only.Cool dehumidified air comes through the outlets selected ...

Operation of the rear system is quite simple. Begin byrotating the rear system center control knob on the frontATC control unit to the “REAR CONTROL” position, thisilluminates an “UNLOCK” symbol in the rear display.Next, rotate the Rear Blower Control and the Rear ModeControl to the “AUTO” positions...

CAUTION! Interior air enters the Rear Automatic TemperatureControl System through an intake grille located inthe passenger side trim panel behind the third seat.The heater outlets are located in the passenger sidetrim panel just behind the sliding door. Do not blockor place objects directly in front...

Window FoggingVehicle windows tend to fog on the inside in mild rainyor humid weather. To clear the windows, use the A/C,PANEL and blower controls. Direct the panel outletstoward the side windows. Do not use the Recirculationmode without A/C for long periods as fogging mayoccur. Interior fogging on ...

A/C Air Filter — If EquippedThe climate control system filters out dust, pollen andsome odors from the air. Strong odors can not be totallyfiltered out. Refer to section 7 “Air Conditioning” forfilter replacement instructions. REAR WINDOW FEATURES Intermittent Rear Wiper Operation — ManualTemperatur...

Electric Rear Window Defroster — If Equipped Press this button to turn on the rear windowdefroster and the optional heated mirrors. A light will show that the defroster is on. The defroster automati-cally turns off after about 10 minutes of operation. If your vehicle is equipped with Infrared Three-...

STARTING AND OPERATING CONTENTS m Starting Procedures . . . . . . . . . . . . . . . . . . . . . 226 ▫ 2.4L Engine . . . . . . . . . . . . . . . . . . . . . . . . . 226 ▫ 3.3L And 3.8L Engine . . . . . . . . . . . . . . . . . . 228 m Engine Block Heater — If Equipped . . . . . . . . . 230 m Automatic...

STARTING PROCEDURES CAUTION! Long periods of engine idling, especially at highengine speeds, can cause excessive exhaust tempera-tures which can damage your vehicle. Do not leaveyour vehicle unattended with the engine running. WARNING! Do not leave animals or children inside parkedvehicles in hot we...

Extremely Cold Weather (below 2 29°C or 2 20°F). To insure reliable starting at these temperatures, use of anexternally powered electric engine block heater (availablefrom your dealer) is recommended. WARNING! Do not attempt to push or tow your vehicle to get itstarted. Vehicles equipped with an aut...

CAUTION! To prevent damage to the starter, do not crank theengine for more than 15 seconds at a time. Wait 10 to15 seconds before trying again. If the engine has been flooded, it may start to run, but nothave enough power to continue running when the key isreleased. If this occurs, continue cranking...

CAUTION! To prevent damage to the starter, do not crank theengine for more than 15 seconds at a time. Wait 10 to15 seconds before trying again. If the engine has been flooded, it may start to run, but nothave enough power to continue running when the key isreleased. If this occurs, continue cranking...

WARNING! Remember to disconnect the cord before driving.Damage to the 110-115 volt electrical cord couldcause electrocution. AUTOMATIC TRANSMISSION CAUTION! Damage to the transmission may occur if the follow-ing precautions are not observed: • Shift into PARK only after the vehicle has come toa comp...

WARNING! It is dangerous to shift the selector lever out of “P” or“N” if the engine speed is higher than idle speed. Ifyour foot is not firmly on the brake pedal, thevehicle could accelerate quickly forward or in re-verse. You could lose control of the vehicle and hitsomeone or something. Only shift...

transmission operating temperature exceeds acceptablelimits. This is done to prevent transmission damage dueto overheating. ALL WHEEL DRIVE — IF EQUIPPED This feature provides full time, on-demand, All WheelDrive (AWD). The system is automatic with no driverinputs or additional driving skills requir...

WARNING! Be sure the parking brake is fully disengaged beforedriving: failure to do so can lead to brake failure, andan accident. BRAKE SYSTEM In the event power assist is lost for any reason (forexample, repeated brake applications with the engineoff), the brakes will still function. The effort req...

• and a slight drop or fall away of the brake pedal at theend of the stop. These are all normal characteristics of ABS. WARNING! The Anti-Lock Brake System contains sophisticatedelectronic equipment that may be susceptible tointerference caused by improperly installed or highoutput radio transmittin...

All vehicle wheels and tires must be the same size andtype and tires must be properly inflated to produceaccurate signals for the computer. POWER STEERING The standard power steering system will give you goodvehicle response and increased ease of maneuverabilityin tight spaces. The system will provi...

TRACTION CONTROL — IF EQUIPPED The Traction Control System reduces wheel slip andmaintains traction at the driving (front) wheels. Thesystem reduces wheel slip by engaging the brake on thewheel that is losing traction (spinning). The systemoperates at speeds below 35 mph (56 km/h). The system is alw...

NOTE: Extended heavy use of Traction Control may cause the system to deactivate and turn on the TRAC andthe OFF indicators located in the instrument cluster. This is to prevent overheating of the brake system and isa normal condition. The system will remain disabled forabout 4 minutes until the brak...

• European Metric tire sizing is based on Europeandesign standards. Tires designed to this standard havethe tire size molded into the sidewall beginning withthe section width. The letter 9 P 9 is absent from this tire size designation. Example: 215/65R15 96H • LT(Light Truck)-Metric tire sizing is b...

Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ( ....blank.... ( = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standardsT = Temporary Spare tire31 = Overall Diameter in Inches (in)215 = Sect...

EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load correspondingto its load index under certain operating conditions.—The maximum speed correspon...

Tire Identification Number (TIN) The TIN may be found on one or both sides of the tirehowever the date code may only be on one side. Tireswith white sidewalls will have the full TIN includingdate code located on the white sidewall side of the tire. Look for the TIN on the outboard side of black side...

Tire Loading and Tire Pressure Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Infor- mation” placard located on the driver’s side “B” pillar. Tire and Loading Information Placard This placard tells you important information about the,1) number of people that can be carried in the...

LoadingThe vehicle maximum load on the tire must not exceedthe load carrying capacity of the tire on your vehicle. Youwill not exceed the tire’s load carrying capacity if youadhere to the loading conditions, tire size and cold tireinflation pressures specified on the Tire and LoadingInformation plac...

2. Economy—Improper inflation pressures can cause uneven wearpatterns to develop across the tire tread. These abnormalwear patterns will reduce tread life resulting in a need forearlier tire replacement. Underinflation also increases tirerolling resistance and results in higher fuel consumption. 3. ...

Radial-Ply Tires WARNING! Combining radial ply tires with other types of tireson your vehicle will cause your vehicle to handlepoorly. The instability could cause an accident. Al-ways use radial ply tires in sets of four (or 6, in caseof trucks with dual rear wheels). Never combinethem with other ty...

These indicators are molded into the bottom of the treadgrooves and will appear as bands when the tread depthbecomes 1/16 inch (2 mm). When the indicators appearin 2 or more adjacent grooves, the tire should be replaced. Many states have laws requiring tire replacement at thispoint. Replacement Tire...

WARNING! • Do not use a tire, wheel size or rating other than thatspecified for your vehicle. Some combinations ofunapproved tires and wheels may change suspen-sion dimensions and performance characteristics,resulting in changes to steering, handling, and brak-ing of your vehicle. This can cause unp...

Improper alignment will not cause vehicle vibration.Vibration may be a result of tire and wheel out-of-balance. Proper balancing will reduce vibration andavoid tire cupping and spotty wear. ALL WHEEL DRIVE (AWD) — IF EQUIPPED CAUTION! All Wheel Drive (AWD) vehicles must have the samesize and type ti...

are significantly underinflated. It is particularly impor-tant, therefore, for you to check the tire pressure in all ofyour tires regularly and maintain proper pressure. 1,2,3, OR 4 TIRE(S) LOW PRESSURE Low tire pressure levels of 28 psi [1.9 bars] (193 kPa) orless detected in one or more tires. Ins...

TIRE PRESSURE NOW AVAILABLE The TPM system is functioning normally and the externalinterference is no longer affecting the system. SPARE TIRE IN USE? YES/NO The TPM system requires more information to determinethe correct mode of operation, one or more of the vehicleactive tires has been replaced by...

General Information This device complies with part 15 of the FCC rules andRSS 210 of Industry Canada. Operation is subject to thefollowing conditions: • This device may not cause harmful interference. • This device must accept any interference received,including interference that may cause undesired...

CAUTION! To avoid damage to your vehicle or tires, observe thefollowing precautions: • Because of restricted chain clearance between tires andother suspension components, it is important that onlychains in good condition are used. Broken chains cancause serious damage. Stop the vehicle immediately i...

Snow tires generally have lower speed ratings than whatwas originally equipped with your vehicle and shouldnot be operated at sustained speeds over 75 mph (120km/h). TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate atdifferent loads and perform different steering, ...

Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’sperformance: • The use of leaded gas is prohibited by Federal law.Using leaded gasoline can impair engine performance,damage the emission control system, and could resultin loss of warranty coverage. • An out-of-tune eng...

• Do not inhale exhaust gases. They contain carbonmonoxide, a colorless and odorless gas which can kill.Never run the engine in a closed area, such as agarage, and never sit in a parked vehicle with theengine running for an extended period. If the vehicle isstopped in an open area with the engine ru...

WARNING! • Remove the fuel tank filler tube cap (gas cap) slowlyto prevent fuel spray from the filler neck which maycause injury. • The volatility of some gasolines may cause a buildupof pressure in the fuel tank that may increase whileyou drive. This pressure can result in a spray ofgasoline and/or...

• Vehicle Identification Number (VIN) • Type of Vehicle • Month Day and Hour of Manufacture (MDH) The bar code allows a computer scanner to read theVehicle Identification Number (VIN). Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.This includes driver, pas...

Figure out the weight on the front and rear of the vehicleseparately. It is important that you distribute the loadevenly over the front and rear axles. Overloading can cause potential safety hazards andshorten useful service life. Heavier axles or suspensioncomponents do not necessarily increase the...

FrontAxle Rear Axle Empty Weight 2140 lbs 1470 lbs Load (Including driver, pass-sengers and cargo) 360 lbs 980 lbs Total 2500 lbs 2450 lbs GAWR 2544 lbs 2544 lbs TRAILER TOWING In this section you will find safety tips and informationon limits to the type of towing you can reasonably dowith your veh...

WHAT TO DO IN EMERGENCIES CONTENTS m Hazard Warning Flasher . . . . . . . . . . . . . . . . . . 280 m If Your Engine Overheats . . . . . . . . . . . . . . . . . 281 m Jacking And Tire Changing . . . . . . . . . . . . . . . . 282 ▫ Jack Location . . . . . . . . . . . . . . . . . . . . . . . . 283 ▫ S...

HAZARD WARNING FLASHER The hazard flasher switch is located in the center of theinstrument panel above the radio. To engage the Hazard Warning Flashers, depress theswitch on the instrument panel. When the Hazard Warn-ing Switch is activated, all directional turn signals will flash on and off to warn...

IF YOUR ENGINE OVERHEATS In any of the following situations, you can reduce thepotential for overheating by taking the appropriate ac-tion. • On the highways — Slow down. • In city traffic — While stopped, put transaxle inneutral, but do not increase engine idle speed. NOTE: There are steps that you...

WARNING! A hot engine cooling system is dangerous. You orothers could be badly burned by steam or boilingcoolant. You may want to call a service center if yourvehicle overheats. If you decide to look under thehood yourself, see Section 7, Maintenance, of thismanual. Follow the warnings under the Coo...

Spare Tire RemovalFit the jack-handle over the drive nut. Rotate the nut tothe left until the spare is on the ground with enough slackcable to allow you to pull the tire out from under thevehicle. CAUTION! The winch mechanism is designed for use with thejack handle only. Use of an air wrench or othe...

• Block both the front and rear of the wheel diagonally oppo-site the jacking position. Forexample, if changing the rightfront tire, block the left rearwheel. • Passengers should not remain in the vehicle when thevehicle is being jacked. Jacking Instructions 1. Remove the spare wheel, scissors jack ...

DRIVING ON SLIPPERY SURFACES Acceleration Rapid acceleration on snow covered, wet, or other slip-pery surfaces may cause the front wheels to pull errati-cally to the right or left. This phenomenon occurs whenthere is a difference in the surface traction under the front(driving) wheels. WARNING! Rapi...

km/h). Exceeding these towing limits may cause a trans-mission geartrain failure. If the transmission is not op-erative, or if the vehicle is to be towed more than 100miles (160 km), the vehicle must be towed with the frontwheels off the ground. All Wheel DriveYour vehicle may be towed under the fol...

If it is necessary to use the accessories while being towed(wipers, defrosters, etc.), the key must be in the ONposition, not the ACCESSORY position. Make certain thetransmission remains in NEUTRAL. Without The Ignition Key Special care must be taken when the vehicle is towedwith the ignition in the...

MAINTAINING YOUR VEHICLE CONTENTS m 2.4L Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . 298 m 3.3L/3.8L Engines . . . . . . . . . . . . . . . . . . . . . . 299 m Onboard Diagnostic System — OBD II . . . . . . . . 300 m Emissions Inspection And MaintenancePrograms . . . . . . . . . . . ...

ONBOARD DIAGNOSTIC SYSTEM — OBD II Your vehicle is equipped with a sophisticated onboarddiagnostic system called OBD II. This system monitorsthe performance of the emissions, engine, and automatictransmission control systems. When these systems areoperating properly, your vehicle will provide excell...

EMISSIONS INSPECTION AND MAINTENANCEPROGRAMS In some localities, it may be a legal requirement to passan inspection of your vehicle’s emissions control system.Failure to pass could prevent vehicle registration. For states which have an I/M (Inspection andMaintenance) requirement, this check verifies...

ignition key or start the engine. This means that yourvehicle’s OBD system is not ready and you should notproceed to the I/M station. b. The MIL will not flash at all and will remain fullyilluminated until you turn off the ignition key or startthe engine. This means that your vehicle’s OBD systemis ...

NOTE: Intentional tampering with emissions control systems can result in civil penalties being assessedagainst you. WARNING! You can be badly injured working on or around amotor vehicle. Do only that service work for whichyou have the knowledge and the proper equipment.If you have any doubt about yo...

To minimize the possibility of catalyst damage: • Do not shut off the engine or interrupt the ignitionwhen the transmission is in gear and the vehicle is inmotion. • Do not try to start engine by pushing or towing thevehicle. • Do not idle the engine with any spark plug wiresdisconnected or removed,...

CAUTION! • It is essential when replacing the cables on thebattery that the positive cable is attached to thepositive post and the negative cable is attached tothe negative post. Battery posts are marked posi-tive (+) and negative (-) and identified on thebattery case. Cable clamps should be tight o...

Steering Linkage The tie rod end ball joints are permanently lubricated anddo not require periodic maintenance. Drive Shaft Universal Joints Your vehicle has constant velocity universal joints. Peri-odic lubrication of these joints is not required. However,the joint boots should be inspected for ext...

Exhaust System The best protection against carbon monoxide entry intothe vehicle body is a properly maintained engine exhaustsystem. Whenever a change is noticed in the sound of the exhaustsystem, when exhaust fumes can be detected inside thevehicle, or when the underside or rear of the vehicle isda...

Adding CoolantWhen adding coolant, or refilling the system, a minimumof 50% solution of ethylene glycol antifreeze coolant inwater should be used. Higher concentrations (not toexceed 70%) are required if temperatures below 2 37°F ( 2 38°C) are anticipated. Use only high purity water such as distille...

Disposal of Used Engine CoolantUsed ethylene glycol based engine coolant is a regulatedsubstance requiring proper disposal. Check with yourlocal authorities to determine the disposal rules for yourcommunity. To prevent ingestion by animals or childrendo not store ethylene glycol based engine coolant...

• Check coolant freeze point in the radiator and in thecoolant recovery bottle. If antifreeze needs to beadded, contents of coolant recovery bottle must also beprotected against freezing. • If frequent coolant additions are required, or if thelevel in the coolant recovery bottle does not drop whenth...

Insure nylon tubing in these areas has not melted orcollapsed. Inspect all hose connections such as clamps and cou-plings to make sure they are secure and no leaks arepresent. Components should be replaced immediately if there isany evidence of wear or damage that could cause failure. Brakes In orde...

Insure nylon tubing in these areas has not melted orcollapsed. Inspect all hose connections such as clamps and cou-plings to make sure they are secure and no leaks arepresent. NOTE: Often, fluid such as oil, power steering fluid, and brake fluid are used during assembly plant opera-tions to facilita...

NOTE: Refer to Section 8 of this manual for Mainte- nance Schedules. If the transmission is disassembled for any reason, thefluid and filter should be changed. Special AdditivesDo not add any fluid additives to the transmission. Theonly exception to this policy is the use of special dyes toaid in de...

transmission fluid, refer to Recommended Fluids, Lubri-cants and Genuine Parts for correct fluid type. To assureperformance, it is important that the proper lubricant beused. Rear CarrierThe fluid should be maintained at the bottom of the fillerhole opening. if it becomes necessary to add or replace...

trees and road surfaces during other seasons, are highlycorrosive to the metal in your vehicle. Outside parking,which exposes your vehicle to airborne contaminants,road surfaces on which the vehicle is operated, extremehot or cold weather and other extreme conditions willhave an adverse effect on pa...

CAUTION! Do not use abrasive or strong cleaning materialssuch as steel wool or scouring powder, which willscratch metal and painted surfaces. Special Care • If you drive on salted or dusty roads or if you drivenear the ocean, hose off the undercarriage at least oncea month. • It is important that th...

The Heated Mirrors, Lower Instrument Panel PowerOutlet and Removable Floor Console, when in the frontposition are fused with self resetting fuses that are onlyserviceable by an authorized dealer. The power seats arefused by a 30 Amp circuit breaker located under thedriver’s seat. The Power Windows a...

BULB REPLACEMENT Headlights 1. Remove the three screws securing the headlight mod-ule. 2. Turn the bulb socket retaining ring counterclockwise. 3. Disconnect the electrical connector and replace thebulb. MAINTAINING YOUR VEHICLE 339 7

CAUTION! Do not touch the new bulb with your fingers. Oilcontamination will severely shorten bulb life. If thebulb comes in contact with an oily surface, clean thebulb with rubbing alcohol. Front Park/Turn Signal and Sidemarker Lights 1. Remove the three screws securing the headlight mod-ule. 2. Twi...

3. Replace bulb, reinstall socket and then reinstall theheadlight module. Front Fog Light 1. Reach behind the front fascia from under the vehicle. 2. Twist the front fog light bulb to remove from the foglight module. 3. Disconnect the electrical connector and replace thebulb. CAUTION! Do not touch t...

Rear Tail, Stop, Turn Signal, Side Marker andBack-up Lights 1. Raise the liftgate. 2. Remove the two light assembly push-in type fasteners. 3. Squeeze the socket assembly tabs to remove it from thehousing. 4. Pull the bulb to remove it from the socket. 5. Replace the bulb, reinstall the socket, and ...

Center High Mounted Stop Light (CHMSL) 1. Remove the two screws securing the CHMSL. 2. Twist the bulb socket to remove from the CHMSLhousing. 3. Pull the bulb out of the socket. 4. Replace the bulb, reinstall the socket and reattach theCHMSL. License Light 1. Remove the two lens assembly mounting sc...

MAINTENANCE SCHEDULES CONTENTS m Emission Control System Maintenance . . . . . . . . 348 m Maintenance Schedules . . . . . . . . . . . . . . . . . . . 348 ▫ Schedule “B” . . . . . . . . . . . . . . . . . . . . . . . . 351 ▫ Schedule “A” . . . . . . . . . . . . . . . . . . . . . . . . 363 8 M A I N T...

EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in boldtype must be done at the times or mileages specified to assure the continued proper functioning of the emissioncontrol system. These, and all other maintenance servicesincluded in this manual, should be done to p...

SCHEDULE “B” Follow schedule “B” if you usually operate your vehicleunder one or more of the following conditions. Changethe automatic transmission fluid and filter every 60,000miles (96 000 km) if the vehicle is usually operated underone or more of the conditions marked with an L . • Day or night t...

Miles 3, 000 6, 000 9, 000 12, 000 15, 000 18, 000 (Kilometers) (5 000 ) (10 000 ) (14 000) (19 000) (24 000) (29 000) Change engine oil and engine oil filter. X X X X X X Inspect the brake linings. X X Inspect the engine air cleaner filter, replace ifnecessary. * X X X X X Replace the engine air cl...

Miles 21, 000 24, 000 27, 000 30, 000 33, 000 36, 000 (Kilometers) (34 000) (38 000) (43 000) (48 000) (53 000) (58 000) Change engine oil and engine oil filter. X X X X X X Inspect the brake linings. X X Inspect the engine air cleaner filter, replace ifnecessary. * X X X X X Replace the engine air ...

Miles 21, 000 24, 000 27, 000 30, 000 33, 000 36, 000 (Kilometers) (34 000) (38 000) (43 000) (48 000) (53 000) (58 000) Change the All Wheel Drive (AWD) overrun-ning clutch and rear carrier fluid. (See the noteat the end of this chart) X Replace the air conditioning filter. X X 354 SCHEDULE “B” 8 M...

Miles 75, 000 78, 000 81, 000 84, 000 87, 000 90, 000 (Kilometers) (120 000) (125 000) (130 000) (134 000) (139 000) (144 000) Change engine oil and engine oil filter. X X X X X X Inspect the brake linings. X X Inspect the engine air cleaner filter, replace ifnecessary. * X X X X Replace the engine ...

IF YOU NEED CONSUMER ASSISTANCE CONTENTS m Suggestions For Obtaining Service For YourVehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 372 ▫ Prepare For The Appointment . . . . . . . . . . . . 372 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . . 372 ▫ Be Reasonable ...

REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If youbelieve that your vehicle has a defect which could causea crash or cause injury or death, you should immediatelyinform the National Highway Traffic Safety Administra-tion (NHTSA) in addition to notifying the manufacturer. If...

Temperature Grades The temperature grades are A (highest), B, and C, repre-senting the tire’s resistance to the generation of heat andits ability to dissipate heat when tested under controlledconditions on a specified indoor laboratory test wheel.Sustained high temperature can cause the material of ...

Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266 Adding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270Additives . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268Clean Air . . . . . . . . . . . . . . . . . . . . . . . . . . . . 266Filler Cap . . . . ...

High Beam/Low Beam Select Switch . . . . . . . . 103Lights On Reminder . . . . . . . . . . . . . . . . . . . . 101Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339Time Delay . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Heated Seats . . . . . . . . . . . . . . . . . . ....

Key-In Reminder . . . . . . . . . . . . . . . . . . . . . . . . . 13Keyless Entry System . . . . . . . . . . . . . . . . . . . . . . 20Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Knee Bolster . . . . . . . . . . . . . . . . . . . . . . . . . . 52,54 Lap/Shoulder Belts ....

Bench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90,92Easy Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85Easy-Out Roller . . . . . . . . . . . . . . . . . . . . . . . . 90Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82Integrated, Child . . . . ....

Vehicle Information Center . . . . . . . . . . . . . . . . . 115Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . 272,274Vehicle Modifications/Alterations . . . . . . . . . . . . . . 7Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . 217,337Vehicle Theft Alarm . . . . . . . . ....