Directed Electronics A600/4 - Manuals

5 FUSE REQUIREMENTS You will need to install an in-line fuse or circuit breaker in the powerwire within 18” of the battery. This fuse or circuit breaker is to protectyour vehicle from fire in case the power wire shorts to the vehiclebody. If you are only using one amplifier, use the fuse ratingindic...

AMPLIFIER STATUS LEDS The LEDs provide the following indications: 1. Power - These LEDs illuminates the center Precision Power logo background when the amplifier power is turned on. 2. Short - These LEDs behind the PPI logo will flash to indicate a short on the output. 2. Thermal - These LEDs behind...

TOOLS/PARTS FOR INSTALLATION NOTE: TOOLS ARE NOT SUPPLIED. Small flat blade screwdriverPhillips screwdriver (#2 or medium sized)Wire cuttersWire strippers4 - #6 round head screws, and 1 - #8 sheet metal screw. (or nut, bolt,flat washer, star washer) (see details)2 - Ring connectors (large enough to ...

WIRING Before beginning, disconnect the negative (-) terminal of the batteryprior to connecting the amplifier to the positive (+) 12V terminal toprevent a short to ground and potential damage to wiring andequipment. Some vehicle radios have an anti-theft feature wherewhen the radio is removed from 1...

Observe the same precautions for routing these wires that youfollowed for running the power and remote turn on wires. Cut offexcess and, using wire strippers, strip 1/4-inch of insulation. Locatethe front speaker/remote turn-on Power Lock TM connector. Using a hex wrench loosen the screws on the upp...

For the rear channels, locate the four terminal speaker Power Lock TM connector. Using a hex wrench loosen the screws on the upperside ofthe connector. Insert the speaker leads into the end and secure withthe hex wrench. Check to be sure you've maintained proper polaritybefore securing each wire. GR...

CHARGING SYSTEM If your total current draw is over 100 amps ( or total output power is over 600 watts ), you are probably exceeding the capability of your charging system. Dimming lights and fluctuating voltage are solidindicators that you need to upgrade your alternator, battery, or both.You should...

load, double its 4 ohm RMS rating. These amplifiers will effectivelydouble their power at this load. 1000W X 1.5 X2 = 3000 watts 3000W = 250 Amps total current draw 12V If you are using more than one amplifier, add up the total currentdraw for all of them and choose the appropriate gauge based on th...

POWER LOCK CONNECTORS Once you have run both the power and ground wires, then connectthe cables to the amplifier. Cut off excess wire, and using wirestrippers, strip the ends of the power and ground cablesapproximately 1/4 inch. Locate the Power Lock TM power and ground connector (supplied). Using a...

suitable subwoofer or center channel. Deriving the mono channel isaccomplished by using the Left Channel Positive wire (L+) as the positive speaker wire and the Right Channel Negative wire (R-) as the negative speaker wire. Note: It is important that a minimum 4 ohm impedance is observed. If the imp...

A600/4 FRONT PLATE DIAGRAM 1. Cooling Plenums: Maintain a minimum 2” clearance around cooling plenums for proper amplifier cooling. 2. Rear Speaker Connector: Speaker Power Lock TM connector. 3. Front Speaker/Remote Connector: Speaker Power Lock TM connector. 4. QBASS TM Level Control: Controls bass...

4 & 5. QBASS TM 1 and QBASS TM 2 Freq.: Use these switches, QBASS TM 1 and QBASS TM 2 to program the QBASS PLUS TM circuit frequency. 6. -12dB Attenuation Switch: Push this switch ‘IN’ for high voltage input (4V-12V) capability. This button must be pushed ‘IN’ for usewith speaker level input on ...

INPUTS There are two sets of RCA jacks on the front end of your amplifier.The RCA cables from your source unit go in the set labeledINPUTS. If your source unit doesn’t have RCA outputs, then add aset of RCA plugs (available at your dealer) to your front or rear setof speaker leads (see drawing below...

ADVANCED INSTRUMENTATION INPUT The Advanced Instrumentation Input has been incorporated fromthe legendary Precision Power TM 2500F1 . This circuit completely isolates the chassis ground from the audio circuit of the amplifierand reduces noise radiated into your signal cables by up to 40dB.This is eq...

25 TC-X CROSSOVER Your new amplifier has a TC-X Crossover (Total Control X-over ® ) 30Hz-4kHz (see this guide for Crossover Chart).12dB per octavephase correlated crossover built-in to provide superior systemflexibility without the added expense and installation of an outboardcrossover. The speaker ...

CROSSOVER DETENT CHART Detent # Low Pass Frequency (Hz) @ -3dB High Pass Frequency (Hz) @ -3dB 123456789 1011121314151617181920212223242526272829303132333435363738394041 282830303032343638424650525460667688 100116136144168198240286310340380424484576632748932 107614281700243628302980 5252525656606472...

INPUT COMBINE Your multi-channel amplifier can use both front and rear outputsfrom your head unit to maintain the ability to fade front to rear, or youcan run a single set of RCAs to the front inputs and push in the RearInput INT/EXT switch on the amplifier endplate to route the frontsignal to the r...

LIMITED TWO YEAR CONSUMER WARRANTY: Directed Electronics promises to the original purchaser, to replace this productshould it prove to be defective in workmanship or material under normal use, fora period of two years from the date of purchase by the dealer as indicated by thedate code marking of th...