Directed Electronics 259D - Manuals

4 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase. Your product warranty will not be validated if your warranty registration is not returned. Please note that it is necessary to k...

9 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . iin nsstta alllla attiio on n Be sure to read this section thoroughly and view the Rattler Do- It-Yourself Installation Video in its entirety before starting the installation. Pay special attention to all warnings to prevent personal injury...

10 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . step 1 Ground Wire The BLACK wire on the main 8-pin harness is ground. This wire should be connected to a clean, paint-free area of metal in the drivers kick panel area. First strip back a ¾-inch section of the insulation off the BLACK wir...

11 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . step 2 Constant Power and Ignition wires Almost all power and ignition wires can be found behind the key cylinder under the lower drivers side dash panel. Using the appropriate hand tools, remove the lower dash panel using care not to brea...

12 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . Once the constant power wire has been identified, solder the two thick RED wires from the relay satellite pack to it and cover the connection with electrical tape to ensure a safe connection. With the meter black lead still in the kick pan...

13 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . If the vehicle requires more than one ignition as per the Web site information follow the same test procedure and solder the thick PINK/WHITE wire to it and be sure to cover your connection with electrical tape. If your vehicle requires mo...

15 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . step 4 Safety Shutdown Wires With all ignition wires properly connected, find the appropriate safety shutdown wires. These include the brake wire, hood pin, and neutral safety wires. First locate the factory brake wire using your multi-met...

16 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . Installing the hood pin switch requires drilling a ¼-inch hole in the metal lip under the hood. Choose a location that will allow the pin switch to be depressed when the hood is closed. The pin switch has a connector on the bottom to conne...

17 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . The last safety shutdown wire is the neutral safety wire. This wire is extremely important as it prevents the vehicle from starting in gear which could cause serious bodily harm. When determining the neutral safety wire it is important to ...

19 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . step 5 Parking light flash There are several different types of parking light circuits. The following description is for a standard negative-triggered parking light circuit, usually located at the light switch. If the web vehicle informati...

20 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . step 6 Door locks Although there are numerous types of door lock circuits, the most common is the negative triggered door lock system. Check the web information on your vehicle to determine your door lock system type. If your vehicle has a...

21 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . Repeat this process for the unlock wire but press the switch to the unlock position when testing. Once you have identified the correct wire, solder the LIGHT BLUE wire off the main connector to it and cover the connection with electrical t...

22 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . enough to actually start the engine, it is possible to change the programming to extend the crank time. Refer to the Programming Options section of this guide. On some vehicles the electrical system has too low of a voltage variance for th...

23 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . voltage should read between 1.5 volts and 2.9 volts. Once thecorrect tachometer wire has been identified, turn the vehicle off. Run the VIOLET/WHITE wire through the firewall along sidethe hood pin wire. Then run it into the engine compart...

25 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . step 9 Immobilizer Bypass Modules Most newer vehicles have a factory engine immobilizer system designed to prevent any unauthorized use of the vehicle. These immobilizers will cut off power to the starter and the fuel supply preventing a t...

26 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . step 10 Testing the system Once steps 1-9 have been completed, the operation of the system can be tested. Place the two 30-amp fuses back into the relay satellite RED wire fuse holders. Make sure that the vehicle is in park with the emerge...

27 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . ttrra an nssm miitttte err ffu un nc cttiio on nss The receiver uses a computer-based learn routine to learn the transmitter buttons. This makes it possible to assign any specific transmitter button, or combination of buttons, to any recei...

28 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . Button I The door locking and unlocking functions are controlled by pressing . Button II Timer Mode is controlled by . Button I and II The remote start function of your system is controlled by pressing and simultaneously. ttrra an nssm mii...

30 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . Program switch. Press it one time and release it to advance from Channel One to Channel Two. Now, press and hold the Program switch. The LED will flash two times. As before, do not release it. If you want to program Channel Three after pro...

31 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . unlocking/disarming To unlock the doors press for one second. The parking lights will flash twice to confirm that the doors are unlocked. ignition-controlled door locks If power door locks have been connected to your system and the ignitio...

32 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . To remote start the vehicle: 1. Simultaneously press and on the transmitter for one second. 2. The parking lights will flash to confirm remote start opera- tion. 3. Once the vehicle has started, it will run for the pre-program- med period ...

33 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . timer mode Timer Mode automatically starts the engine and runs it for a pre-programmed time period, every three hours for a total of six operation cycles. This feature helps to ensure that your engine will start in the morning after a nigh...

34 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . 1. Start the engine by pressing and . 2. Press and release . 3. Within two seconds press and release and again. 4. The engine will shut down and the parking lights will flash four times to confirm that Timer Mode has been exited. If the ca...

35 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . ffe ea attu urre ess m me en nu u The factory settings are indicated in bold text in the table below. note: The number in parentheses indicate the number of times the LED will flash. Feature L LE ED D O On n SSeettttiin ngg LED Off Setting...

41 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . sse ec cu urriittyy & & c co on nvve en niie en nc ce e e exxp pa an nssiio on nss Listed below are some of the many expansion options availablefor use with your system. Some options may require additionalparts and/or labor. Please...

43 © 2 0 0 2 d i r e c t e d e l e c t r o n i c s , i n c . n no otte ess _________________________________________________ _________________________________________________ _________________________________________________ _________________________________________________ _________________________...

The company behind this system is Directed Electronics, Inc. Since its inception, Directed Electronics has had one purpose, to provide consumers withthe finest vehicle security and car stereo products and accessories available. The recipient ofnearly 100 patents and Innovations Awards in the field o...