Dimplex DHEBPTS - Manuals - manualsarea.com

Page 2 - Important Instructions: Retain for future use.

1 IMPORTANT SAFEGUARDS ............................................................... 3 2 Connecting the Controller .................................................................. 5 3 Securing Your Electric Blanket .......................................................... 6 4 Using The Controll...

Page 3 - IMPORTANT SAFEGUARDS

Thank you for purchasing our Electric Blanket. Each unit is manufactured to ensure safety and reliability. Before using for the first time, please read the instruction manual carefully and keep it for future reference. 1 IMPORTANT SAFEGUARDS • Before connecting and switching on the blanket, ensure t...

Page 5 - Connecting the Controller; Do Not fold, roll or kink the cable. Allow the cable to hang freely.

• Only use the controllers supplied with this blanket. • For additional protection, it is strongly recommend that the use of a residual current device (RCD) with a tripping current not exceeding 30mA be used on the circuit supplying this product. If you are unsure if your home has this device, pleas...

Page 6 - Securing Your Electric Blanket; HEAD

FAILURE TO FOLLOW THESE FITTING INSTRUCTIONS MAY TRIGGER THE OVERHEAT PROTECTION SYSTEM AND RENDER THE BLANKET PERMANENTLY INOPERATIVE. THIS MAY INVALIDATE THE WARRANTY. 3 Securing Your Electric Blanket Note: Your electric blanket must be placed directly onto the mattress. If using a mattress protec...

Page 7 - Using The Controller; TURN OFF AND UNPLUG THE BLANKET WHEN NOT IN USE; Electrical Field Effect

4 Using The Controller • Use your Electric Blanket with Detachable Controller Model MC-102A Only. • Do not use any other controller for this blanket. 0 = Off 1 = Low Heat (Suitable for all night use) 2 = Medium Heat 3 = High Heat (For preheating the bed only) 0 = Off • To select the required heat se...

Page 8 - Overheat / Element Protection; The controller must not be covered; . The controller has built in protection, so that if

4.2 Auto Off This controller is fitted with a 12 hour Count Down Auto Off Timer which starts to countdown from when your heat setting has been selected, and will switch power off to the elements after approximately 12 hours. (+/- 30Minutes). Note : Once a heat setting has been selected and the switc...

Page 9 - Recommended Cleaning Instructions

• Should this occur, the Blanket and Front Heat Level display lights will turn off and a RED indicator light will illuminate through the back of the controller. This indicates that the Blanket and controller needs to be replaced and cannot be repaired. If in a bright room, you may need to cup your h...

Page 11 - Note; Servicing Your Blanket and Controller/s; the back of this manual before contacting our service department.; Storage

6.4 Drying • Spread the blanket out on a clean surface (e.g. a large table) to dry in a shady area. • Your blanket can also be dried on a clothes line provided the blanket is not creased or folded. • Ensure pegs are not used on the element areas of the blanket if hanging on the line. Note : The blan...

Page 12 - Troubleshooting; Testing Controllers; The unit is packed carefully back into its original packaging.

9 Troubleshooting 9.1 Testing Controllers Before contacting the service department please follow the steps below to determine if there is actually a fault, and if so, if a fault is within the blanket or within the controller. This will make it easier when talking to the service department. Please al...

Page 13 - Troubleshooting Table; Problem

9.2 Troubleshooting Table Problem Cause Remedy No Power to Controller / No Heat Level Indicator Lights showing on Front Display and No RED light showing through the back of the controller when a heat setting is selected The Temperature Slide Knob is in the “O” position Slide the knob to setting 1, 2...

Page 14 - ) in respect of the Dimplex product which this warranty; the Dimplex

10 Warranty This warranty is provided by Glen Dimplex Australia Pty Limited ABN 69 118 275 460 of Unit 1, 21 Lionel Road, Mount Waverley, Victoria 3149 (Phone number 1300 556 816), or in New Zealand by Glen Dimplex Australasia Limited, New Zealand registration number 1506305, of 38 Harris Road, East...

Page 15 - To make a valid claim under this warranty, you must:; Warranty claims

c) the repair relates to the replacement of consumable parts such as fuses in plugs and bulbs or any other parts of the Dimplex product which require routine replacement; d) you are unable to provide us with reasonable proof of purchase for the Dimplex product; e) the breakdown occurs after the expi...

Page 16 - Costs of warranty claim; in Australia or; Glen Dimplex Australia Pty Ltd.; Mount Waverley VIC 3149; DISPOSAL

Goods presented for repair may be replaced by refurbished goods of the same type rather than being repaired. Refurbished parts may be used to repair the goods. Dimplex products are designed and supplied for normal domestic use. We will not be liable to you under this warranty for business loss or da...