Digi MIL-4511H - Manuals - manualsarea.com

Page 2 - Install Guide; M i c r o M o d u l e s u s e d w i t h t h e M I L - 4 5 1 1 H :; Micro Module Installation Guide; Figure 2.Rear Panel of the MIL-4511H with SNMP; T h e M I L - 4 5 1 1 H P a c k a g e C o n t e n t s

Install Guide Model: MIL-4511H 2 M i c r o M o d u l e s u s e d w i t h t h e M I L - 4 5 1 1 H : • MIL-4310M • MIL-4320M • MIL-4330M • MIL-4340M • MIL-4350M • MIL-4360M • MIL-4370M For instructions on configuring the micro modules, see the MIL-4300M Series Micro Module Installation Guide . Figure ...

Page 3 - D e s c r i p t i o n o f H a r d w a r e; • Green indicates; D e s c r i p t i o n o f D i p S w i t c h e s; FUNCTION

Install Guide Model: MIL-4511H 3 D e s c r i p t i o n o f H a r d w a r e The MIL-4511H is a 24-port, 10BASE-T SNMP managed hub with a modular uplink port supporting 10BASE-T, 10BASE2, 10BASE-BASE-FL, or AUI connectivity, and an RS-232 port for out-of-band management. The MIL-4511H supports standar...

Page 4 - D B - 9 S e r i a l P o r t; For instructions on configuring the micro modules, see the; Function

Install Guide Model: MIL-4511H 4 D B - 9 S e r i a l P o r t I n s t a l l a t i o n P r o c e d u r e Follow these steps to connect the MIL-4511H to your network: 1. Remove the MIL-4511H and the power cord from the shipping box. 2. Connect the appropriate UTP Ethernet cabling to the front ports. 3....

Page 5 - I n s t a l l a t i o n o f R a c k M o u n t E a r s; of the hub with a Phillips head screwdriver.; I n s t a l l a t i o n o f t h e R u b b e r F e e t; Remove the plastic stickers on of the rubber feet.

Install Guide Model: MIL-4511H 5 I n s t a l l a t i o n o f R a c k M o u n t E a r s D o t h e f o l l o w i n g t o i n s t a l l t h e r a c k m o u n t e a r s 1. Starting with one side of the hub, remove the three screws closest to the front of the hub with a Phillips head screwdriver. 2. Plac...

Page 6 - I n s t a l l a t i o n o f t h e I n t e r c o n n e c t C a b l e; To stack multiple hubs:; Figure 3.Stacking Multiple Hubs; Continue until all of the hubs are cascaded to the MIL-4511H. W

Install Guide Model: MIL-4511H 6 I n s t a l l a t i o n o f t h e I n t e r c o n n e c t C a b l e The interconnect cable is used to connect multiple hubs in a stack. The connector at the end of the cable is a 6-wire, straight-through, RJ-11 connector. Connect the interconnect cable into one of th...

Page 7 - P o r t R e d u n d a n c y; Every device on a TCP/IP network is identified by two addresses:

Install Guide Model: MIL-4511H 7 P o r t R e d u n d a n c y The port redundancy capability allows a workstation to be connected to two ports in the stack. The LinkSentry feature shuts off out going link pulses on a port when incoming link pulses stop. This allows the MIL-4511H to be used with a red...

Page 8 - S e t t i n g t h e I P A d d r e s s w i t h Te l n e t; alpha; Warning: Entering monitor will lock out

Install Guide Model: MIL-4511H 8 S e t t i n g t h e I P A d d r e s s w i t h Te l n e t The following only works if the MIL-4511H is on the same subnet as the host from which you want to telnet. In this example, you are to add a MIL-4511H called alpha with an IP address 192.185.2.3 and an Ethernet...

Page 9 - S e t t i n g t h e I P A d d r e s s w i t h R A R P; S e t t i n g t h e I P A d d r e s s w i t h B O O T P

Install Guide Model: MIL-4511H 9 S e t t i n g t h e I P A d d r e s s w i t h R A R P RARP provides a way for devices on the network to query a server for their IP address at start-up. This only works if the 4511H is on the same subnet as the host running the RARP daemon. however, it will RARP if i...

Page 10 - To s e t t h e I P A d d r e s s w i t h B O O T P o n a H P / U X s y s t e m :; BOOTP Device Adapter Type; Ethernet

Install Guide Model: MIL-4511H 10 3. Add the host name and address, and then save the file. For example, for a MIL-4511H called alpha with an IP address 192.185.2.3 , add this line: 192.185.2.3 alpha 4. Edit BOOTP in the /etc directory containing the hostname of the MIL-4511H, hardware type, hardwar...

Page 11 - V e r i f y i n g t h e I P A d d r e s s i s S e t P r o p e r l y

Install Guide Model: MIL-4511H 11 If the BOOTP process is successful, the SYS LED flashes five times per second until the MIL-4511H resolves its IP address. It flashes once per second after address resolution. Note: The IP address in this case is stored in RAM. When the MIL-4511H is powered off, the...

Page 12 - L e g a l; R e g u l a t o r y A p p r o v a l s; FCC Class A; C a n a d i a n E M I N o t i c e; Product serial number and rev.; Address: 1299 Orleans Drive; Five-Year Limited Warranty

Doc. Number: 75424 Rev. A L e g a l R e g u l a t o r y A p p r o v a l s • FCC Class A • UL 1950 • CSA 22 No. 950 • EN60950 • CE – EN55022 Class B– EN50082-1 C a n a d i a n E M I N o t i c e This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Re...