Dewalt 550 - Manuals - manualsarea.com

Page 3 - Model 550 Tube Severing Tool; SAFETY PRECAUTIONS; IN GENERAL

3 Model 550 Tube Severing Tool 92-0116 : Rev. 060810 SAFETY PRECAUTIONS WARNING: IN GENERAL When using rotating head cutting equipment, basic safety precautions should alwaysbe followed to reduce the risk of personal injury. Operate this tool only in accordance with specific operating instructions. ...

Page 6 - GENERAL DESCRIPTION

6 TRI TOOL INC. 92-0116 : Rev. 060810 GENERAL DESCRIPTION The Model 550 Tube Severing Tool series of tube cutters is designed to cut tubing inareas where access to and around the tube is limited. The Model 550 uses a cutter wheel to sever the tube. Normal operation will notproduce chips. The Model 5...

Page 7 - SPECIFICATIONS

7 Model 550 Tube Severing Tool 92-0116 : Rev. 060810 SPECIFICATIONS Envelope, Model 550-00, Tube Severing Tool

Page 9 - MAINTENANCE

9 Model 550 Tube Severing Tool 92-0116 : Rev. 060810 MAINTENANCE All components should be periodically cleaned and coated with a light film of oil. Use a clean, non-detergent oil, preferably SAE 10 (90 SSU or lighter.) The Cutting Wheel should be replaced if worn or damaged. The Cutting Wheel life d...

Page 10 - OPERATION

10 TRI TOOL INC. 92-0116 : Rev. 060810 OPERATION Read the operating instructions carefully before attempting to operate the Model 550Tube Severing Tool. Be sure to use eye protection at all times when operating the Model 550. Select the proper Model 550 for the size of tubing to be severed. Maximum ...

Page 11 - Disconnect the Drive Unit from its power source

11 Model 550 Tube Severing Tool 92-0116 : Rev. 060810 NOTE: Select the proper Tri Tool Inc. Drive Unit that best suits the operation needed to beperformed. Drive Input Location A non Tri Tool Inc. Drive Unit will void the warranty. If input is counterclockwise, sever damage will occur during cutting...

Page 13 - REPAIRS AND REPLACEMENT

13 Model 550 Tube Severing Tool 92-0116 : Rev. 060810 WARNING: REPAIRS AND REPLACEMENT Cutter Wheel Replacement Disconnect the Drive Unit from the Model 550 Tube Cutter prior to any repairsor replacements. Rotate the drive shaft manually clockwise to rotate the cutter carriage to the desiredposition...

Page 15 - AIR DRIVE ASSEMBLY

15 Model 550 Tube Severing Tool 92-0116 : Rev. 060810 AIR DRIVE ASSEMBLY REMOVAL OF A SHEARED ROLL PIN FROM THE DRIVE ASSY. Push the Air Drive Assy into the Model 550 Tube Cutter and rotate it clockwise andpull it out. Unscrew the Bayonet Mounting Tube from the Motor Housing by rotating theBayonet M...

Page 16 - TROUBLE SHOOTING; Problem: The Tool Bit Chatters

16 TRI TOOL INC. 92-0116 : Rev. 060810 TROUBLE SHOOTING Problem: The Tool Bit Chatters Probable causes: The tool bit is loose or overextended.The tool bit is damaged.The tool holder is too loose in the slides.The cutting speed is too fast.The clamping pads are loose on the pipe or tube.Cutting fluid...

Page 18 - ACCESSORIES

18 TRI TOOL INC. 92-0116 : Rev. 060810 ACCESSORIES The following accessories are recommended for use with the Model 550 Tube Cut-ters and are available from TRI TOOL INC. 1. Portable Air Filter (P/N 75-0115) 2. Drive Assembly, Air (P/N 04-0084) 3. Shaft Assembly, 18” Flexible (P/N 14-0036) 4. Motor ...

Page 19 - ILLUSTRATED PARTS BREAKDOWN

19 Model 550 Tube Severing Tool 92-0116 : Rev. 060810 MODEL 550-03, 04, 05, AND 06 TUBE SEVERING TOOL ASSEMBLY (P/N 01-XXXX) ILLUSTRATED PARTS BREAKDOWN 1 10 2 3 4 5 7 6 8 9 11 12 13 15 14 17 16 25 10 22 18 24 26 23 21 20 4 9 19

Page 20 - Item

20 TRI TOOL INC. 92-0116 : Rev. 060810 02-2057 CARRIAGE ASSEMBLY, CUTTER 1 1. 19-0353 HOUSING, CARRIAGE, TUBE CUTTER 1 2. 32-0003 PIN, ROLL, 1/16" DIA X 1/2" 1 3. 32-0179 PIN, DOWEL, 3/16" DIA X 5/8" 1 4. 32-0226 PIN, DOWEL, 3/16" DIA X 1" LONG 2 5. 32-0251 PIN, CUTTER 1 6. 3...

Page 43 - DEWALT SAFETY INSTRUCTIONS

43 Model 550 Tube Severing Tool 92-0116 : Rev. 060810 The DeWALT Cordless Drill/Driver comes with an 'Instruction Manual' and should bereferenced for all safety and operating procedures. DEWALT SAFETY INSTRUCTIONS