Delta 31-280 - Manuals - manualsarea.com

Page 4 - GROUNDING INSTRUCTIONS

4 4 Fig. 1 Fig. 2 GROUNDED OUTLET BOX CURRENT CARRYING PRONGS GROUNDING BLADEIS LONGEST OF THE 3 BLADES GROUNDED OUTLET BOX GROUNDING MEANS ADAPTER GROUNDING INSTRUCTIONS WARNING: THIS TOOL MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROMELECTRIC SHOCK. 1. All grounded, cord-connected tool...

Page 5 - EXTENSION CORDS; CHANGING VOLTAGE

2 5 Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cordwhich has a 3-prong grounding type plug and matching receptacle which will accept the tool’s plug. When using anextension cord, be sure to use one heavy enough to carry the current of the...

Page 6 - ASSEMBLY INSTRUCTIONS; ASSEMBLING STAND; OPERATING INSTRUCTIONS; FOREWORD; UNPACKING AND CLEANING

6 ASSEMBLY INSTRUCTIONS WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWERSOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED, AND YOU READ ANDUNDERSTAND THE ENTIRE OWNER'S MANUAL. Fig. 7 ASSEMBLING STAND 1. Attach the four rubber feet (E) Fig. 7 to the bottom of each leg (C). 2. Att...

Page 8 - OPERATING CONTROLS AND ADJUSTMENTS; STARTING AND STOPPING THE TOOL; ATTACHING DUST CHUTE

8 OPERATING CONTROLS AND ADJUSTMENTS STARTING AND STOPPING THE TOOL The on-off switch (A) Fig. 14 is located on the sander base. To turn the sander “ON”, move the switch to the up position. Toturn the sander “OFF”, move the switch to the down position. LOCKING SWITCH IN THE “OFF” POSITION IMPORTANT:...

Page 9 - OVERLOAD PROTECTION

9 Fig. 17 Fig. 16 IMPORTANT: THE TOOL IS SHIPPED WITHOUT BELT TENSION. BEFORE OPERATING THE TOOL, ADJUST THE BELTFOR CORRECT TENSION AND PROPER TRACKING BY DOING THE FOLLOWING: 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Loosen the two lock knobs (A) Fig. 17, and remove the top cover (B). 3. Turn the b...

Page 10 - TILTING THE BELT SANDER TABLE

ADJUSTING BELT SANDER TABLE MITER GAUGE SLOTPARALLEL TO SANDING BELT 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Position the table (Figs. 25 and 26) 90 degrees to the belt. Place a square (B) in the miter gauge slot with the blade (C) of the square touching the sanding belt. Check the opposite end of ...

Page 11 - CHANGING POSITION OF SANDING ARM; ADJUSTING SANDING DISC TABLE 90 DEGREES TO DISC

11 Fig. 28 Fig. 27 Fig. 26 Fig. 25 CHANGING POSITION OF SANDING ARM 1. The sanding arm (A) can be used in the vertical position (Fig. 27), the horizontal position (Fig. 28), or any angle in between. Loosen the lock handle (B), position the arm (A) to the desired angle, and tighten the lock handle (B...

Page 12 - TILTING THE DISC SANDER TABLE

12 Fig. 31 Fig. 30 Fig. 32 TILTING THE DISC SANDER TABLE The table (A) can be tilted 45 degrees up (Fig. 31), or 45 degrees down (Fig. 32), by loosening the lock handle (B), tilt-ing the table (A), and tightening lock handle (B). The degree of tilt is determined by the scale (C) Fig. 32, and pointer...

Page 13 - ADJUSTING SANDING DISC GUARD; ACCESSORY HOLDER

13 ADJUSTING SANDING DISC GUARD 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Adjust the sanding disc guard (A) Fig. 35, so that the front edge of the guard is slightly in front of the sanding disc for small work, and slightly behind the sanding disc for large work.3. To adjust, move the guard (A) Fig. 3...

Page 14 - REPLACING SANDING BELT; REPLACING SANDING DISC

POWER TAKE-OFF SHAFT 1. DISCONNECT TOOL FROM POWER SOURCE. 2. A power take-off shaft is provided on the lower end of the sanding belt arm to accommodate accessories. 3. For access to the power take-off shaft, remove the two screws (A) Fig. 43, and cover (B). 4. WARNING: Unguarded rotating shafts (C)...

Page 15 - ACCESSORIES; PARTS, SERVICE OR WARRANTY ASSISTANCE; Two Year Limited Warranty

15 15 ACCESSORIES A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers, and Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or for the name of your nearest supplier. WARNING: Since accesso...

Page 16 - DELTA SERVICE CENTERS; CANADIAN PORTER-CABLE

16 The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): BAMMER ® , INNOVATION THAT WORKS ® , JETSTREAM ® , LASERLOC ® , OMNIJIG ® , POCKET CUTTER ® , PORTA-BAND ® , PORTA-PLANE ® , PORTER- CABLE ® , QUICKSAND ® , SANDTRAP ® , SAW BOSS ® , S...