Delta 23-725 - Manuals - manualsarea.com

Page 2 - SAFETY RULES; SAVE THESE INSTRUCTIONS

2 SAFETY RULES Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, thereare certain hazards involved with the operation of the product. Using the machine with respect and caution willconsiderably lessen the possibility of personal injury. How...

Page 4 - UNPACKING AND CLEANING

4 UNPACKING AND CLEANING Carefully unpack the tool and all loose items from the carton. Remove the protective coating from all unpainted parts.This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline, or lacquerthinner for this purpose). Fig. 1 illustrates ...

Page 5 - HARDWARE ILLUSTRATION

5 HARDWARE ILLUSTRATION Fig. 2 illustrates the hardware components of the grinder. ACTUAL SIZE Fig. 2 M10 x 1.50 x 30 M8 x 1.25 x 18 M8 x 1.25 x 15 M8 x 1.25 x 10 M6 x 1.0 x 15 M6 x 1.0 x 18 M10 M8 M6 M6 x 1.0

Page 6 - ASSEMBLY INSTRUCTIONS; ASSEMBLING TOOL RESTS; ASSEMBLING SPARK GUARDS

6 ASSEMBLY INSTRUCTIONS ASSEMBLING TOOL RESTS 1. The tool rest arms (F) Fig. 3, are universal and can be attached to either side of the grinder. Assembleadjustable tool rest (J) Fig. 3, to left side of tool rest arm(F) Fig. 3, as shown, and fasten with one bolt (1) Fig. 2,and one washer (7) Fig. 2, ...

Page 7 - ASSEMBLING EYE SHIELDS; ASSEMBLING WATER TRAY

7 Fig. 6 Fig. 7 D C C D Fig. 9 A A Fig. 8 B ASSEMBLING EYE SHIELDS Your grinder is supplied with two eye shields for operator protection. NOTE: ALWAYS WEAR EYE PROTECTION. To assemble the eye shields, proceed as follows: 1. Assemble long end of eye shield mounting rod (D) Fig. 1, to the side of each...

Page 8 - ASSEMBLING PEDESTAL

8 ASSEMBLING PEDESTAL (MODELS 23-730 & 23-735) NOTE: Pedestal hardware is illustrated ACTUAL SIZE Fig. 10. 1. Stand the column up with the square end on the floor Fig. 11. 2. Place the base on top of the round end of the column, and line up bolt holes Fig. 12. 3. Insert bolt (11) and washer (12)...

Page 9 - EXTENSION CORDS; MINIMUM GAUGE EXTENSION CORD; CONNECTING TOOL TO POWER SOURCE; POWER CONNECTIONS

9 Use proper extension cords. Make sure your extensioncord is in good condition and is a 3-wire extension cordwhich has a 3-prong grounding type plug and a 3-polereceptacle which will accept the tool’s plug. When usingan extension cord, be sure to use one heavy enough tocarry the current of the saw....

Page 10 - FLEXIBLE LAMP

10 Fig. 17 A 2. Grounded, cord-connected tools intended for use ona supply circuit having a nominal rating less than 150volts: This tool is intended for use on a normal 120-volt circuitand has a grounded plug that looks like the plugillustrated in Fig. 15. If a properly grounded outlet is not availa...

Page 11 - GRINDING WHEELS; DRESSING A GRINDING WHEEL

11 STARTING ANDSTOPPING GRINDER The “ON-OFF” switch (A) Fig. 18 is located on the front of the grinder. To turn the grinder “ON” move the switch to the right, and to turn the grinder “OFF” move the switch to the left. GRINDING WHEELS WARNING: THE USE OF ACCESSORIES AND ATTACHMENTS NOT RECOMMENDED BY...

Page 12 - CHANGING GRINDING WHEELS; DUST PORT

12 CHANGING GRINDING WHEELS CAUTION: DISCONNECT MACHINE FROMPOWER SOURCE BEFORE CHANGINGGRINDING WHEELS. 1. When changing wheels, remove the three screws (A) Fig. 20, attaching the side covers to the grinder andremove the side cover (B). 2. To prevent shaft rotation, place a wedge between the grindi...

Page 13 - OPERATIONS

13 OPERATIONS IMPORTANT: KEEP SPARK GUARDS AND EYESHIELDS IN PLACE AT ALL TIMES. Figures 23, 24, and 25, illustrate several typicaloperations that can be accomplished using the grinder.Each tool rest should be positioned a little below thecenter of the grinding wheel and adjusted so the edge ofthe t...

Page 14 - Two Year Limited Warranty

14 PARTS, SERVICE OR WARRANTY ASSISTANCE All Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof Porter-Cable Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional information regarding your Delta quality produ...

Page 15 - NOTES