Dell Z90DW- Manuals

Dell Z90DW– Installation Manual in PDF format online.

Manuals:

Installation Manual

Installation Manual Dell Z90DW

Summary

Page 2 - Copyright Notices; Trademarks

Copyright Notices © 2014, Dell Inc. All Rights Reserved. This manual and the software and firmware described in it are copyrighted. You may not reproduce, transmit, transcribe, store in a retrieval system, or translate into any language or computer language, in any form or by any means, electronic, ...

Page 3 - Contents; Introduction

Contents 1 Introduction 1 Kit Contents 1Kit Warranty 2Overview 2Dell Technical Support 2 Related Documentation and Services 2Dell Online Community 2 2 Installing Z Class Flash 3 Requirements 3Procedures 3 3 Installing WES7p Firmware 7 Requirements 7Procedures 8Troubleshooting 13 USB Keys - Troublesh...

Page 4 - iv

Page 5 - CAUTION; Kit Contents

1 Introduction This guide provides step-by-step instructions to use Wyse USB Firmware Tool to convert the following Wyse Z class thin clients to WES7p: • Z90D7 • Z90S7 • Z90DE7 • Z90DW • Z90SW CAUTION : WES7p firmware requires Z class thin clients to have a minimum of 8 GB Flash and 4 GB RAM (16 GB ...

Page 6 - Related Documentation and Services

2 Chapter 1 · mbr.img · par1.img · par2image1.img · par2image2i.img · vmlinuz Kit Warranty The warranty on the hardware component of this kit assumes the remaining months of warranty of the thin client in which it is installed, or for 90 days, whichever is greater. Installation of this kit will not ...

Page 7 - Installing Z Class Flash; Requirements; Small Phillips screwdriver; WARNING; Procedures; thin client for disconnecting and reconnecting the thin client.; Figure 2 Removing the cover screws

2 Installing Z Class Flash This chapter contains information for users of Wyse Z class thin clients who must install new flash. If you are installing firmware only, you can skip this chapter and proceed to "Installing WES7p Firmware." Requirements • Small Phillips screwdriver WARNING : Flash...

Page 8 - Chapter 2; Figure 3 Unlatching the cover; Grasp the overhanging cover edge and raise the edge; Figure 4 Removing the cover; Remove the cover to expose the flash module, as shown in Figure 5.; : Flash modules may be susceptible to damage by Electro-Static

4 Chapter 2 4. Place your thumbs on the top surface above where the end screws were removed. With a continuous motion, push firmly downward and towards the back panel (pushing down unlatches the hooks under the cover). The cover will shift approximate 1/4 inch to hang over the back panel, as shown i...

Page 9 - Figure 5 Removing the existing flash module; Align the cover screw tabs with screw holes and press downward; Figure 6 Reattaching the cover; , Attach the screws in the reverse order as described in step 3.

Installing Z Class Flash 5 7. Remove the existing flash module. Locate the flash module and use the Phillips Screwdriver to remove its retaining screw as shown in Figure 5. Lift the flash module out of the socket. Figure 5 Removing the existing flash module 8. Install the new flash module in the rev...

Page 11 - Installing WES7p Firmware; TIP; : You must perform the steps to create and use the; Machine with a; minimum of 16 GB of free space; running either of the following:; : During the USB key configuration process the USB keys will be

3 Installing WES7p Firmware This chapter includes the requirements and procedures you need to install and use Wyse USB Firmware Tool to update your thin client to WES7p firmware. TIP : The purpose of the USB Firmware Tool is to configure a bootable USB key for device firmware. In the following proce...

Page 12 - Hard Drive; Figure 7 Wyse USB Firmware Tool wizard; Click; Next; to open the; Select an Option

8 Chapter 3 Procedures IMPORTANT : Complete the following procedures as an administrator (administrator privileges are required). Step 1: Copy the Z Class WES7p Conversion Image Folder (on the DVD-ROM) to Your Local Hard Drive Navigate to the Z Class WES7p Conversion Image folder (contained on the C...

Page 13 - Figure 8 Configuration options; Select the; Configure the USB key to Copy/Pull or to Update/Push firmware; and then click; Select the Configuration

Installing WES7p Firmware 9 Figure 8 Configuration options 3. Select the Configure the USB key to Copy/Pull or to Update/Push firmware option, and then click Next to open the Select the Configuration dialog box. Figure 9 Update firmware options - Windows Embedded Standard 7 P 4. Select the Windows E...

Page 17 - Step 7: Obtain a Firmware Update; Troubleshooting; USB Keys - Troubleshooting Boot Issues; USB Flash Drives

Installing WES7p Firmware 13 Step 7: Obtain a Firmware Update After converting your thin clients, obtain any available firmware update at http://www.wyse.com/serviceandsupport/support/downloads.asp . WARNING : Use of the Software on more than one device requires that you first purchase from Dell add...

Page 18 - Written and published by:

Installation Guide Dell ® Wyse Z Class Conversion to WES7p Issue: 021214 Written and published by: Dell Inc., February 2014 Created using FrameMaker ® and Acrobat ®