Dell R910- Manuals

Page 2 - Cable Routing Procedures for DellTM PowerEdgeTM R910 Systems; Page ii; Dell; are trademarks of Dell Inc.

Cable Routing Procedures for Dell™ PowerEdge™ R910 Systems Page ii THIS WHITE PAPER IS FOR INFORMATIONAL PURPOSES ONLY, AND MAY CONTAIN TYPOGRAPHICAL ERRORS AND TECHNICAL INACCURACIES. THE CONTENT IS PROVIDED AS IS, WITHOUT EXPRESS OR IMPLIED WARRANTIES OF ANY KIND. © 2010 Dell Inc. All rights reser...

Page 3 - Contents; Table of Figures

Cable Routing Procedures for Dell™ PowerEdge™ R910 Systems Page 1 Contents Introduction ........................................................................................................................................................... 2 Section 1: Cabling a Dell™ PowerEdge™ R910 With a Cabl...

Page 4 - Page 2; Introduction; Best Practices; Follow the instructions contained in the; Rack Installation Guide; in the rail kit to install the server into; Connecting the CMA Cables to the System; Attach the CMA tray to the back of the rails as described in the; CMA Installation Instructions; provided

Cable Routing Procedures for Dell™ PowerEdge™ R910 Systems Page 2 Introduction This white paper covers recommended cable routing procedures for Dell™ PowerEdge™ R910 systems in the following racks: • PowerEdge™ 4210 • PowerEdge™ 2410 • PowerEdge™ 4220 • PowerEdge™ 2420 If you are using the optional ...

Page 5 - Page 3; Routing the Power Cables Through the Strain Reliefs; Figure 2: Routing Power Cables Through the Strain Reliefs; Routing the Cables Through the CMA; white paper; Left-Side Mounting Instructions

Cable Routing Procedures for Dell™ PowerEdge™ R910 Systems Page 3 1.2 Routing the Power Cables Through the Strain Reliefs After you have installed the tray and cables, route the power cables through the strain reliefs located on the power supply handles as shown in Figure 2. Figure 2: Routing Power ...

Page 6 - Page 4

Cable Routing Procedures for Dell™ PowerEdge™ R910 Systems Page 4 Figure 3: Routing the Cables Through the CMA Figure 4: Left-Side Mounted CMA Installation Cables entering the CMA should have a small amount of slack to avoid cable strain when the CMA is extended. NOTE: Do not store excess cable slac...

Page 7 - Page 5; Right-Side Mounting Instructions; Figure 5: Right-Side Mounted CMA Installation

Cable Routing Procedures for Dell™ PowerEdge™ R910 Systems Page 5 1.5 Right-Side Mounting Instructions 1. Install the CMA on the rear right side of the rails by attaching both CMA housings to the attachment brackets on the rails. 2. Route the cables through the CMA while avoiding twisting the cables...

Page 8 - Page 6; Section 2: Cabling a DellTM PowerEdgeTM R910 System Without a CMA; NOTE; Figure 6: Cable Routing Without a CMA; Removing the CMA Brack ets for Shallow Racks; Figure 7: Removing the CMA Brackets for Shallow Racks

Cable Routing Procedures for Dell™ PowerEdge™ R910 Systems Page 6 Section 2: Cabling a Dell™ PowerEdge™ R910 System Without a CMA NOTE : The CMA on Dell™ PowerEdge™ R910 systems is optional. Without the CMA installed, the system must be powered down and all cables disconnected before it can be remov...

Page 9 - Replacing a Power Supply with a Left-Side Mounted CMA; Figure 8: Replacing the Power Supply

Cable Routing Procedures for Dell™ PowerEdge™ R910 Systems Page 7 Section 3: Replacing a Power Supply on a PowerEdge™ R910 System With a CMA NOTE : The steps described below apply to the bottom two power supplies only. The top two power supplies can be replaced with the CMA in its closed (retracted)...