Dell Networking S6000- Manuals

2 CLI Basics This chapter describes the command line interface (CLI) structure and command modes. The Dell Networking operating software commands are in a text-based interface that allows you to use the launch commands, change command modes, and configure interfaces and protocols. Accessing the Comm...

When another user enters CONFIGURATION mode, Dell Networking OS sends a message similar to the following: % Warning: User "admin" on line vty2 "172.16.1.210" is in configuration In this case, the user is “admin” on vty2. Obtaining Help As soon as you are in a command mode there are s...

Navigating the CLI Dell Networking OS displays a CLI prompt comprised of the host name and CLI mode. • Host name is the initial part of the prompt and is “Dell” by default. You can change the host name with the hostname command. • CLI mode is the second part of the prompt and reflects the current CL...

show run | grep ethernet does not return the previous search result because it only searches for instances containing a noncapitalized “ethernet” show run | grep Ethernet ignore-case returns instances containing both “Ethernet” and “ethernet” no-more does not paginate the display output save copies ...

Usage Information You can activate VRF application on a device by using the feature vrf command in CONFIGURATION mode. The no feature vrf command is not supported on any of the platforms. Example Dell#show feature Feature State ------------------------------ VRF enabled Command Modes To navigate and...

CONTROL-PLANE Mode To manage control-plane traffic, use CONTROL-PLANE mode. For more information, refer to Control Plane Policing (CoPP) . To enter CONTROL-PLANE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the control-plane-cpuqos command. The prompt changes to include (co...

To enter ISIS ADDRESS-FAMILY mode: 1. Verify that you are logged in to ROUTER ISIS mode. 2. Enter the command address-family ipv6 unicast . The prompt changes to include (conf- router_isis-af_ipv6). LLDP Mode To enable and configure Link Layer Discovery Protocol (LLDP), use LLDP mode. For more infor...

To enter MONITOR SESSION mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the monitor session command then the session ID. The prompt changes to include (conf- mon-sess- sessionID ). MULTIPLE SPANNING TREE (MSTP) Mode To enable and configure MSTP, use MULTIPLE SPANNING TREE mod...

PREFIX-LIST Mode To configure a prefix list, use PREFIX-LIST mode.To enter PREFIX-LIST mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the ip prefix-list command. Include a name for the prefix list. The prompt changes to include (conf-nprefixl). You can return to CONFIGURATION...

2. Use the router bgp command then enter the AS number. The prompt changes to include (conf- router_bgp). You can return to CONFIGURATION mode by using the exit command. ROUTER ISIS Mode To enable and configure Intermediate System to Intermediate System (ISIS), use ROUTER ISIS mode. For more informa...

SPANNING TREE Mode To enable and configure the Spanning Tree protocol, use SPANNING TREE mode. For more information, refer to Spanning Tree Protocol (STP) . To enter SPANNING TREE mode: 1. Verify that you are logged in to CONFIGURATION mode. 2. Enter the protocol spanning-tree stp-id command. The pr...

3 File Management This chapter contains command line interface (CLI) commands needed to manage the configuration files as well as other file management commands. cd Change to a different working directory. S6000 Syntax cd directory Parameters directory (OPTIONAL) Enter one of the following: • flash:...

HTTP Copy via CLI Copy one file to another location. Dell Networking OS supports IPv4 and IPv6 addressing for FTP, TFTP, and SCP (in the hostip field). This feature is supported on S6000 platform. Syntax copy http://10.16.206.77/sample_file flash://sample_filecopy flash://sample_file http://10.16.20...

In this copy scp: flash: example, specifying SCP in the first position indicates that the target is to be specified in the ensuing prompts. Entering flash: in the second position indicates that the target is the internal Flash. The source is on a secure server running SSH, so you are prompted for th...

Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Int...

CAUTION: This command deletes all files, including the startup configuration file. So, after executing this command, consider saving the running config as the startup config (use the write memory command or copy run start command). Related Commands copy – copies the current configuration to either t...

show boot system Displays information about boot images currently configured on the system. S6000 Syntax show boot system {stack-unit {0-11 | 0-7 | 0-5 | all} } Parameters all Enter the keyword all to display the boot image information for all line cards and rpms. stack-unit Enter the keyword stack-...

show bootvar Display the variable settings for the boot parameters. S6000 Syntax show bootvar Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The follo...

Dell(conf-if-te-0/5)# Dell# Example (S6000) Dell#S6000#show version Dell Real Time Operating System Software Dell Operating System Version: 2.0 Dell Application Software Version: 9-4(0-119) Copyright (c) 1999-2014 by Dell Inc. All Rights Reserved. Build Time: Tue Mar 18 10:32:02 PDT 2014 Build Path:...

A Enter the keyword A to upgrade the bootflash partition A B Enter the keyword B to upgrade the bootflash partition B. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS C...

The total amount of space allowed is 16 FP Blocks. System flow requires three blocks and these blocks cannot be reallocated. The ipv4acl profile range is from 1 to 4. When configuring space for IPv6 ACLs, the total number of Blocks must equal 13. Ranges for the CAM profiles are from 1 to 10, except ...

Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. configure Enter CONFIGURATION mode from EXEC Privilege mode. S6000 Syntax configure [terminal] Parameters terminal (OPTIONAL) Enter the keyword terminal to specify that you are configuring from the terminal. Command Modes EXEC Pr...

disable Return to EXEC mode. S6000 Syntax disable [ level ] Parameters level (OPTIONAL) Enter a number for a privilege level of the Dell Networking OS. The range is from 0 to 15. The default is 1 . Defaults 1 Command Modes EXEC Privilege Command History This guide is platform-specific. For command i...

enable Enter EXEC Privilege mode or any other privilege level configured. After entering this command, you may need to enter a password. S6000 Syntax enable [ level ] Parameters level (OPTIONAL) Enter a number for a privilege level of Dell Networking OS. The range is from 0 to 15. Defaults 15 Comman...

end Return to EXEC Privilege mode from other command modes (for example, CONFIGURATION or ROUTER OSPF modes). S6000 Syntax end Command Modes • CONFIGURATION• SPANNING TREE• MULTIPLE SPANNING TREE• LINE• INTERFACE• TRACE-LIST• VRRP• ACCESS-LIST• PREFIX-LIST• AS-PATH ACL• COMMUNITY-LIST• ROUTER OSPF• ...

ip ftp password Specify a password for outgoing FTP connections. S6000 Syntax ip ftp password [ encryption-type ] password To remove a password and return to the default setting, use the no ip ftp password [ password ] command. Parameters encryption-type (OPTIONAL) Enter one of the following numbers...

ip ftp source-interface Specify an interface’s IP address as the source IP address for FTP connections. S6000 Syntax ip ftp source-interface interface To delete an interface, use the no ip ftp source-interface interface command. Parameters interface Enter the following keywords and slot/port or numb...

Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. ip tftp vrf Configures an TFTP client with a VRF that is used to connect to the TFTP server. Syntax ip tftp [vrf vrf-name ] To undo the TFTP client configuration, use the no ip tftp [vrf vrf-name ] command. Parameters vrf vrf-nam...

ip ftp vrf Configures an FTP client with a VRF that is used to connect to the FTP server. Syntax ip ftp [vrf vrf-name ] To undo the FTP client configuration, use the ip ftp [vrf vrf-name ] command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to specify the VRF that is ...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. Related Commands ip ssh server —...

FTOS(conf)#ip telnet server vrf management FTOS(conf)#no ip telnet server vrf ip telnet source-interface Set an interface’s IP address as the source address in outgoing packets for Telnet sessions. S6000 Syntax ip telnet source-interface interface To return to the default setting, use the no ip teln...

ftp-server username — sets a username and password for incoming FTP connections to the E-Series. line Enable and configure console and virtual terminal lines to the system. This command accesses LINE mode, where you can set the access conditions for the designated line. S6000 Syntax line {aux 0 |con...

ping Test connectivity between the system and another device by sending echo requests and waiting for replies. S6000 Syntax ping [ host | ip-address | ipv6-address ] [count { number | continuous}] [ datagram-size ] [ timeout ] [ source (ip src-ipv4- address) | interface ] [ tos ] [ df-bit (y | n) ] ...

Type Ctrl-C to abort. Sending 5, 100-byte ICMP Echos to 172.31.1.255, timeout is 2 seconds: Reply to request 1 from 172.31.1.208 0 ms Reply to request 1 from 172.31.1.216 0 ms Reply to request 1 from 172.31.1.205 16 ms :: Reply to request 5 from 172.31.1.209 0 ms Reply to request 5 from 172.31.1.66 ...

Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series Original command. Usage Information If there is a change in the configuration, FTOS prompts you to save the new configuration. Or you can save your running configuration with the copy running-config comm...

Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.5.1.0 Introduced on the E-Series. Usage Information Messages can contain an unlimited number of lines; however, each line is limited to 255 character...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version...

Example Dell#show cpu-traffic-stats Processor : CP -------------- Received 100% traffic on GigabitEthernet 8/2 Total packets:100 LLC:0, SNAP:0, IP:100, ARP:0, other:0 Unicast:100, Multicast:0, Broadcast:0 Processor : RP1 --------------- Received 62% traffic on GigabitEthernet 8/2 Total packets:500 L...

Example Dell#show debug Generic IP: IP packet debugging is on for ManagementEthernet 0/0 Port-channel 1-2 Port-channel 5 GigabitEthernet 4/0-3,5-6,10-11,20 GigabitEthernet 5/0-1,5-6,10-11,15,17,19,21 ICMP packet debugging is on for GigabitEthernet 5/0,2,4,6,8,10,12,14,16 Dell# show environment View ...

0 0 down UNKNOWN down 0 0 1 up AC up 6504 Dell#show environment thermal-sensor -- Thermal Sensor Readings (deg C) -- Unit Sensor0 Sensor1 Sensor2 Sensor3 Sensor4 Sensor5 Sensor6 --------------------------------------------------------------- -------------------- 0 39 36 37 37 31 31 46 show inventory...

0 7 QSFP 40GBASE-CR4-1M APF11200012UR1 Yes 0 8 QSFP 40GBASE-CR4-1M APF12300017GEY Yes 0 9 QSFP 40GBASE-CR4-1M APF12300017GEY Yes 0 10 QSFP 40GBASE-CR4-1M APF12300017GEY Yes Related Commands • show interfaces — displays the interface configuration. • show interfaces transceiver — displays the physica...

Usage Information The output for show memory displays the memory usage of LP part (sysdlp) of the system. The sysdlp is an aggregate task that handles all the tasks running on the S-Series’ CPU. Example Dell#show memory stack-unit 0 Statistics On Unit 0 Processor =========================== Total(b)...

show processes memory (S-Series) — displays CPU usage information based on processes running in an S-Series. show processes ipc flow-control Display the single window protocol queue (SWPQ) statistics. S6000 Syntax show processes ipc flow-control [cp] Syntax show processes ipc flow-control [cp | rp1 ...

show processes memory Display memory usage information based on processes running in the S-Series or Z-Series system. S6000 Syntax show processes memory {management-unit | stack unit { unit-id | all | summary}} Parameters management-unit Enter the keyword management-unit for CPU memory usage of the ...

Example (management-unit) Dell#show processes management-unit Total : 151937024, MaxUsed : 111800320 [2/25/2008 4:18:53] CurrentUsed: 98848768, CurrentFree: 53088256 SharedUsed : 13007848, SharedFree : 7963696 PID Process ResSize Size Allocs Frees Max Current 337 KernLrnAgMv 117927936 0 0 0 0 0 331 ...

LACP 0 0x00000000 0x00000000 0x8000383f 0x00000000 35 DHCP 0 0x00000000 0x00000000 0x800000c2 0x0000c000 37 V6RAD 0 0x00000433 0x00030000 0x00000000 0x00000000 0 Unidentified Client0 0x006e0002 0x00000000 0x00000000 0x00000000 0 Dell# show system Display the status of all stack members or a specific...

terminal length Configure the number of lines displayed on the terminal screen. S6000 Syntax terminal length screen-length Parameters screen-length Enter a number of lines. Entering zero causes the terminal to display without pausing. The range is from 0 to 512. Defaults 24 lines Command Modes • EXE...

NOTE: The :: notation specifies successive hexadecimal fields of zeros. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a...

5 802.1X An authentication server must authenticate a client connected to an 802.1X switch port. Until the authentication, only extensible authentication protocol over LAN (EAPOL) traffic is allowed through the port to which a client is connected. After authentication is successful, normal traffic p...

debug dot1x Display 802.1X debugging information. S6000 Syntax debug dot1x [all | auth-pae-fsm | backend-fsm | eapol-pdu] [interface interface ] Parameters all Enable all 802.1X debug messages. auth-pae-fsm Enable authentication PAE FSM debug messages. backend-fsm Enable backend FSM debug messages. ...

Defaults 60 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Vers...

Dell#show dot1x cos-mapping interface tengigabitethernet 0/32 mac-address 00:00:00:00:00:10 Supplicant Mac: 0 0 0 0 0 10 Lookup for Mac: 802.1p CoS re-map table on Te 0/32: ---------------------------------- 802.1p CoS re-map table for Supplicant: 00:00:00:00:00:10 Dot1p Remapped Dot1p 0 7 1 6 2 5 3...

6 Access Control Lists (ACL) Access control lists (ACLs) are supported by the Dell Networking operating software on the S6000 platform.Dell Networking OS supports the following types of ACL, IP prefix list, and route maps: • Commands Common to all ACL Types• Common IP ACL Commands• Standard IP ACL C...

show config Display the current ACL configuration. S6000 Syntax show config Command Modes • CONFIGURATION-STANDARD-ACCESS-LIST• CONFIGURATION-EXTENDED-ACCESS-LIST• CONFIGURATION-MAC ACCESS LIST-STANDARD• CONFIGURATION-MAC ACCESS LIST-EXTENDED Command History This guide is platform-specific. For comm...

The supports both Ingress and Egress IP ACLs. NOTE: Also refer to the Commands Common to all ACL Types section. access-class Apply a standard ACL to a terminal line. S6000 Syntax access-class access-list-name To remove an ACL, use the no access-class access-list-name command. Parameters access-list-...

Use the vrf attribute of this command to associate an access-list to a non-default VRF. You can use this command at the interface context (physical/LAG) to apply the access-list to a range of VRFs. The VRF MODE is not available for the default and management VRFs. Related Commands ip access-list sta...

Standard Ingress IP access list test on TenGigabitEthernet 0/88 Total cam count 2 seq 5 permit 1.1.1.0/24 count (0 packets) seq 10 deny 2.1.1.0/24 count (0 packets Dell#show ip accounting access-list L3-ACL vrf vrf3 ! Standard Ingress IP access list L3-ACL on vrf3 Total cam count 3 seq 5 permit 10.1...

Usage Information Dell Networking OS supports one ingress and one egress IP ACL per interface. Prior to Dell Networking OS version 7.8.1.0, names are up to 16 characters long. The number of entries allowed per ACL is hardware-dependent. For detailed specifications on entries allowed per ACL, refer t...

resequence access-list Re-assign sequence numbers to entries of an existing access-list. S6000 Syntax resequence access-list {ipv4 | ipv6 | mac} { access-list-name StartingSeqNum Step- to-Increment } Parameters ipv4 | ipv6 | mac Enter the keyword ipv4 or mac to identify the access list type to reseq...

Usage Information When you have exhausted all the sequence numbers, this feature permits re-assigning a new sequence number to entries of an existing access-list. seq Assign a sequence number to a deny or permit filter in an IP access list while creating the filter. S6000 Syntax seq sequence-number ...

Extended IP ACL Commands When an ACL is created without any rule and then applied to an interface, ACL behavior reflects an implicit permit. The following commands configure extended IP ACLs, which in addition to the IP address, also examine the packet’s protocol type. The supports both Ingress and ...

Version 6.5.1.0 Expanded to include the optional QoS order priority for the ACL entry. Usage Information The order option is relevant in the context of the Policy QoS feature only. For more information, refer to the Quality of Service chapter of the Dell Networking OS Configuration Guide . When you ...

Version 8.3.1.0 Added the keyword dscp . Version 8.2.1.0 Allows ACL control of fragmented packets for IP (Layer 3) ACLs. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.4.1.0 Added support for non-contiguous mask and added the monitor option. Version 6.5.1.0 Expanded to include the op...

When you use the log option, the CP processor logs details the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. The C-Series and S-Series cannot count both packets and bytes; when you enter the cou...

Command Modes CONFIGURATION-EXTENDED-ACCESS-LIST Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command....

Example An ACL rule with a TCP port lt 1023 uses only one entry in the CAM. Rule# Data Mask From To #Covered 1 0000000000000000 1111110000000000 0 1023 1024 Total Ports: 1024 Related Commands ip access-list extended — creates an extended ACL. permit — assigns a permit filter for IP packets. permit u...

When you use the log option, the CP processor logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. If you configure the sequence-number , the sequence-number is used as a tie bre...

show mac access-lists Display all of the Layer 2 ACLs configured in the system, whether or not they are applied to an interface, and the count of matches/mismatches against each ACL entry displayed. S6000 Syntax show mac access-lists [ access-list-name ] [interface interface ] [in | out] Parameters ...

show mac accounting access-list Display MAC access list configurations and counters (if configured). S6000 Syntax show mac accounting access-list access-list-name interface interface in | out Parameters access-list-name Enter the name of a configured MAC ACL, up to 140 characters. interface interfac...

Version 7.5.1.0 Introduced on the C-Series pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information The ACL hit counters in this command increment the counters for each matching rule, not just the first matching rule. Example Dell#show mac accounting access-list TestMac interface tengigabit...

Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Added the monitor option. pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information When you use the log option, the CP processor logs details about the packets that match. Depending on how many packets match the log entry and at wh...

Usage Information When you use the log option, the CP processor logs details about the packets that match. Depending on how many packets match the log entry and at what rate, the CP may become busy as it has to log these packets’ details. NOTE: When ACL logging and byte counters are configured simul...

pre-Version 6.1.1.0 Introduced on the E-Series. Example Dell(conf-nprefixl)#show config ! ip prefix-list snickers Dell(conf-nprefixl)# show ip prefix-list detail Display details of the configured prefix lists. S6000 Syntax show ip prefix-list detail [ prefix-name ] Parameters prefix-name (OPTIONAL) ...

seq 10 deny 2.1.0.0/16 ge 23 (hit count: 0) seq 25 permit 192.0.0.0 bitmask 192.0.0.0 (hit count: 800) show ip prefix-list summary Display a summary of the configured prefix lists. S6000 Syntax show ip prefix-list summary [ prefix-name ] Parameters prefix-name (OPTIONAL) Enter a text string as the n...

Route Map Commands When you create an access-list without any rule and then applied to an interface, the ACL behavior reflects implicit permit.To configure route maps and their redistribution criteria, use the following commands. continue To a route-map entry with a higher sequence number, configure...

match interface To match routes whose next hop is on the interface specified, configure a filter. S6000 Syntax match interface interface To remove a match, use the no match interface interface command. Parameters interface Enter the following keywords and slot/port or number information: • .• For th...

Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Increased the name string to accept up to 140 characters. Prior to 7.8.1.0, names are up to 16 characters long. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the ...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version...

pre-Version 6.1.1.0 Introduced on the E-Series. Related Commands match community — redistributes routes that match the COMMUNITY attribute. set level To specify the IS-IS level or OSPF area to which matched routes are redistributed, configure a filter. S6000 Syntax set level {backbone | level-1 | le...

Usage Information The set local-preference command changes the LOCAL_PREF attribute for routes meeting the route map criteria. To change the LOCAL_PREF for all routes, use the bgp default local-preference command. Related Commands bgp default local-preference — changes the default LOCAL_PREF attribu...

If you configure the set next-hop command with the interface’s IP address (either Loopback or physical), the software declares the route unreachable. Related Commands match ip next-hop — redistributes routes that match the next-hop IP address. set origin To manipulate the BGP ORIGIN attribute, confi...

Related Commands neighbor bfd disable — Explicitly disables a BFD session with a BGP neighbor or a BGP peer group. ip route bfd Enable BFD for all neighbors configured through static routes. S6000 Syntax ip route bfd [interval interval min_rx min_rx multiplier value role {active | passive}] To disab...

Version 9.2.(0.0) Introduced on Z9000, S4810, and S4820T. Version 8.2.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. neighbor bfd Explicitly enable a BFD session with a BGP neighbor or a BGP peer group. S6000 Syntax ne...

8 Boot Command Line Interface BCLI commands are supported on the S6000 platform only. S6000 To access this BOOT_USER mode, first boot your Dell Networking platform. When you see the “Press ESC to stop auto-boot”, press the ESC key to log into BCLI You enter BOOT_USER mode immediately, as indicated b...

boot message Use this command to enable/disable boot logs during reload. S6000 Syntax boot message on | off Parameters on Enter the keyword on to turn on boot logs during reload. off Enter the keyword off to suppress the boot logs during reload. NOTE: By default, watchdog is disabled. Defaults None ...

boot write net config retries Set the number of retries for network boot configuration failure. S6000 Syntax boot write net config retries <int> Command Modes BOOT_USER Command History Version 9.0.2.0 Introduced on the S6000. Example BOOT_USER # boot write net config retries 2 Updated number o...

Command History Version 9.0.2.0 Introduced on the S6000. Usage Information When you enter the reload command and the system reboots, you will not be prompted for a password to enter the EXEC Privilege mode (normally you are required to enter the enable command). If your console or Telnet session exp...

Command Modes BOOT_USER Command History Version 9.0.2.0 Introduced on the S6000. Usage Information In the runtime CLI, use the ip address command in INTERFACE mode to change the Management interface’s IP address. To view the current IP address configured on the Management interface, enter the show i...

reload Exit from this mode and reload Dell Networking OS. S6000 Syntax reload Command Modes BOOT_USER Command History Version 9.0.2.0 Introduced on the S6000. serial console Use the serial console to set the serial console baud rate. S6000 Syntax serial console <int> <int> Parameters ser...

Related Commands interface_management_ethernet_ip_address — Assign an IP address to the Management Ethernet interface. reload — Configure speed, duplex, and negotiation settings for the management interface. show serial console baud rate Use the show serial console to show the values of the serial c...

9 Border Gateway Protocol BGP is an external gateway protocol that transmits interdomain routing information within and between autonomous systems (AS). BGP version 4 (BGPv4) supports classless inter-domain routing (CIDR) and the aggregation of routes and AS paths. Basically, two routers (called nei...

bgp asnotation Allows you to implement a method for AS number representation in the command line interface (CLI). S6000 Syntax bgp asnotation [ asplain | asdot+ | asdot ] To disable a dot or dot+ representation and return to ASPLAIN, enter the no bgp asnotation command. Defaults asplain Command Mode...

bgp confederation peers Specify the autonomous systems (ASs) that belong to the BGP confederation. S6000 Syntax bgp confederation peers as-number [ ...as-number ] To return to the default, use the no bgp confederation peers command. Parameters as-number Enter the AS number. The range is from 0 to 65...

Related Commands bgp confederation identifier — configures a confederation ID. bgp four-octet-as-support — enables 4-byte support for the BGP process. bgp dampening Enable BGP route dampening and configure the dampening parameters. S6000 Syntax bgp dampening [ half-life reuse suppress max-suppress-t...

Version 7.8.1.0 Introduced on the S-Series. Version 7.7.1.0 Introduced on the C-Series. Usage Information Peering sessions are reset when you change the router ID of a BGP router. This command automatically restarts the BGP instance for the configuration to take effect. clear ip bgp Reset BGP sessio...

Related Commands bgp recursive-bgp-next-hop — disables next-hop resolution through other routes learned by the BGP. clear ip bgp dampening Clear information on route dampening and return the suppressed route to the Active state. S6000 Syntax clear ip bgp [vrf vrf-name ] dampening [ ip-address mask ]...

clear ip bgp flap-statistics Clear BGP flap statistics, which includes number of flaps and the time of the last flap. S6000 Syntax clear ip bgp [vrf vrf-name ] flap-statistics [ ip-address mask | filter-list as-path-name | regexp regular-expression ] Parameters vrf vrf-name (OPTIONAL) Enter the keyw...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.4.(0.0) Added support for VRF. Version...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.4.(0.0) Added support for VRF. Version...

show debugging — views enabled debugging operations. debug ip bgp dampening View information on routes being dampened. S6000 Syntax debug ip bgp [vrf test | ipv4 {unicast | multicast} | ipv6 {unicast | multicast} dampening To disable debugging, use the no debug ip bgp ipv4 multicast dampening comman...

Parameters ip-address (OPTIONAL) Enter the IP address of the neighbor in dotted decimal format. peer-group peer-group-name (OPTIONAL) Enter the keyword peer-group then the name of the peer group. in (OPTIONAL) Enter the keyword in to view only events on inbound BGP messages. out (OPTIONAL) Enter the...

peer-group peer-group-name (OPTIONAL) Enter the keyword peer-group then the name of the peer group. in (OPTIONAL) Enter the keyword in to view only inbound keepalive messages. out (OPTIONAL) Enter the keyword out to view only outbound keepalive messages. Command Modes EXEC Privilege Command History ...

in (OPTIONAL) Enter the keyword in to view BGP notifications received from neighbors. out (OPTIONAL) Enter the keyword out to view BGP notifications sent to neighbors Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version...

neighbor activate This command allows the specified neighbor/peer group to be enabled for the current AFI/SAFI (Address Family Identifier/Subsequent Address Family Identifier). S6000 Syntax neighbor [ ip-address | peer-group-name ] activate To disable, use the no neighbor [ ip-address | peer-group-n...

neighbor advertisement-interval Set the advertisement interval between BGP neighbors or within a BGP peer group. S6000 Syntax neighbor { ip-address | peer-group-name } advertisement-interval seconds To return to the default value, use the no neighbor { ip-address | peer- group-name } advertisement-i...

neighbor advertisement-start To send BGP routing updates, set the minimum interval before starting. S6000 Syntax neighbor { ip-address } advertisement-start seconds To return to the default value, use the no neighbor { ip-address } advertisement-start command. Parameters ip-address (OPTIONAL) Enter ...

peer-group-name Enter the name of the peer group to set the advertisement interval for all routers in the peer group. number Enter a number of times to allow this neighbor ID to use the AS path. The range is from 1 to 10. Defaults Not configured. Command Modes ROUTER BGP Command History This guide i...

neighbor description Assign a character string describing the neighbor or group of neighbors (peer group). S6000 Syntax neighbor { ip-address | peer-group-name } description text To delete a description, use the no neighbor { ip-address | peer-group- name } description command. Parameters ip-address...

Parameters ip-address Enter the IP address of the neighbor in dotted decimal format. peer-group-name Enter the name of the peer group to apply the distribute list filter to all routers in the peer group. prefix-list-name Enter the name of an established prefix list. If the prefix list is not configu...

no prepend Specifies that local AS values do not prepend to announcements from the neighbor. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Referen...

neighbor password Enable message digest 5 (MD5) authentication on the TCP connection between two neighbors. S6000 Syntax neighbor { ip-address | peer-group-name } password [ encryption- type ] password To delete a password, use the no neighbor { ip-address | peer-group- name } password command. Para...

Parameters peer-group-name Enter a text string up to 16 characters long as the name of the peer group. Defaults Not configured. Command Modes ROUTER BGP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Li...

When you remove all clients of a route reflector using the no neighbor route- reflector-client command, the router no longer functions as a route reflector. If the clients of a route reflector are fully meshed, you can configure the route reflector to not reflect routes to specified clients by using...

Usage Information Peers that are enabled within a peer group are disabled when their peer group is disabled. The neighbor shutdown command terminates all BGP sessions on the BGP neighbor or BGP peer group. Use this command with caution as it terminates the specified BGP sessions. When a neighbor or ...

Version 7.4.1.0 Introduced. Usage Information This command enables soft-reconfiguration for the BGP neighbor specified. BGP stores all the updates the neighbor receives but does not reset the peer-session. You cannot set this configuration for a peer that is associated with a peer group. Similarly, ...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version...

Related Commands redistribute — redistributes routes into BGP. network backdoor Specify this IGP route as the preferred route. S6000 Syntax network ip-address mask backdoor To remove a network, use the no network ip-address mask backdoor command. Parameters ip-address Enter an IP address in dotted d...

show capture bgp-pdu neighbor Display BGP packet capture information for an IPv4 address on the system. S6000 Syntax show capture bgp-pdu neighbor ipv4-address Parameters ipv4-address Enter the IPv4 address (in dotted decimal format) of the BGP address to display packet information for that address....

*>I 66.0.0.0/24 172.16.0.2 0 0 500 i *>I 77.0.0.0/24 172.16.0.2 0 0 i Dell#show ip bgp cluster-list 4.4.4.4 BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.6 Status codes: s suppressed, S stale, d dampened, h history, * valid, > best Path sour...

show ip bgp community-list View routes that a specific community list affects. S6000 Syntax show ip bgp [vrf vrf-name ] [ ipv4 unicast ] community-list community-list-name [exact-match] Parameters vrf vrf-name (OPTIONAL) Enter the keywords vrf and then the name of the VRF to view routes affected by ...

Field Description Network Displays the destination network prefix of each BGP route. Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if assigned. LocPrf Displays the B...

Field Description Path Lists all the ASs the dampened route passed through to reach the destination network. Example Dell#show ip bgp dampened-paths BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0 BGP local router ID is 192.168.11.5 Status codes: s suppressed, S stale, d dampened, h hi...

AFIndex 0 NdSpFlag 0x41a190b0 : AFRttP 0x41a0d200 : NdRTMMkrP 0x41a19d28 : NdRTMAFTblVer 0 : NdRibCtxAddr 1101110688 NdRibCtxAddrLen 255 : NdAFPrefix 0 : NdAfNLRIP 0 : NdAFNLRILen 0 : NdAFWPtrP 0 NdAFWLen 0 : NdAfNH : NdAFRedRttP 0x41a0d400 : NdRecCtxAdd 1101110868 NdRedCtxAddrLen 255 : NdAfRedMkrP ...

show ip bgp filter-list View the routes that match the filter lists. S6000 Syntax show ip bgp [vrf vrf-name ] [ ipv4 unicast ] filter-list as-path- name Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view route information that matches the filter lists corre...

Field Description• c = external confederation route entry• n = network route entry• r = redistributed route entry Next Hop Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then local routes exist in the routing table. Metric Displays the BGP route’s metric, if as...

show ip bgp inconsistent-as View routes with inconsistent originating autonomous system (AS) numbers; that is, prefixes that are announced from the same neighbor AS but with a different AS-Path. S6000 Syntax show ip bgp [vrf vrf-name ] [ ipv4 unicast ] inconsistent-as Parameters vrf vrf-name (OPTION...

Field Description Next-hop Displays the next-hop IP address. Via Displays the IP address and interface used to reach the next hop. RefCount Displays the number of BGP routes using this next hop. Cost Displays the cost associated with using this next hop. Flaps Displays the number of times the next h...

Dell#show ip bgp paths Total 2 Paths Refcount Metric Path 1 0 200 i 1 0 200 i show ip bgp paths community View all unique COMMUNITY numbers in the BGP database. S6000 Syntax show ip bgp [vrf vrf-name ] paths community Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf to view all unique COMMUN...

Field Description Address Displays the internal address where the path attribute is stored. Hash Displays the hash bucket where the path attribute is stored. Refcount Displays the number of BGP routes using these communities. Community Displays the community attributes in this BGP path. Example Dell...

Peer-group members (* - outbound optimized): 172.16.0.2 Dell# Related Commands neighbor peer-group (assigning peers) — assigns a peer to a peer-group. neighbor peer-group (creating group) — creates a peer group. show ip bgp regexp Display the subset of the BGP routing tables matching the regular exp...

*> 66.0.0.0/24 172.16.0.2 0 200 i show ip bgp summary Allows you to view the status of all BGP connections. S6000 Syntax show ip bgp [vrf vrf-name ] [ ipv4 unicast ] summary Parameters vrf vrf-name (OPTIONAL) Enter the keyword vrf and then the name of the VRF to view the status of all BGP connect...

show running-config bgp To display the current BGP configuration, use this feature. S6000 Syntax show running-config bgp Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS...

holdtime Enter a number for the time interval, in seconds, between the last keepalive message and declaring the router dead. The range is from 3 to 65535. The default is 180 seconds . Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information ...

10 Content Addressable Memory (CAM) Content addressable memory (CAM) commands are supported on the Dell Networking S6000 platform. NOTE: Not all CAM commands are supported on all platforms. Be sure to note the platform when looking for a command. WARNING: If you are using these features for the firs...

12 Data Center Bridging (DCB) Data center bridging (DCB) refers to a set of IEEE Ethernet enhancements that provide data centers with a single, robust, converged network to support multiple traffic types, including local area network (LAN), server, and storage traffic.The Dell Networking operating s...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.16.0 Introduced on the MXL 10/40GbE Switch IO Module. Usage Information By default, iSCSI is enabled on the unit and flow control is enabled on all of the interfa...

Related Commands dcb-input — creates a DCB input policy. show dcb Displays the data center bridging status, the number of PFC-enabled ports, and the number of PFC-enabled queues. S6000 Syntax show dcb [stack-unit unit-number ] [port-set port-set port-set number ] Parameters unit number Enter the DCB...

show interface pfc statistics Displays counters for the PFC frames received and transmitted (by dot1p priority class) on an interface. S6000 Syntax show interface port-type slot/port pfc statistics Parameters port-type Enter the port type. slot/port Enter the slot/port number. Command Modes INTERFAC...

ETS Commands The following ETS commands are supported on the S6000 platform. dcb-enable Enable data center bridging. S6000 Syntax dcb enable[ pfc-queues 1|4 ] To disable DCB, use the no dcb enable command. Parameters pfc-queues Enter the pfc-queue range. To disable DCB, use the no dcb enable command...

clear ets counters Clear all ETS TLV counters on an interface. S6000 Syntax clear ets counters port-type slot/port Parameters port-type Enter the keywords port-type then the slot/port information. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command...

1 0% ETS 2 0% ETS 3 0% ETS 4 0% ETS 5 0% ETS 6 0% ETS 7 0% ETS Priority# Bandwidth TSA 0 13% ETS 1 13% ETS 2 13% ETS 3 13% ETS 4 12% ETS 5 12% ETS 6 12% ETS 7 12% ETS Remote Parameters: ------------------- Remote is disabled Local Parameters : ------------------ Local is enabled TC-grp Priority# Ban...

Usage Information DCBX requires that you enable LLDP to advertise DCBX TLVs to peers. Configure DCBX operation at the INTERFACE level on a switch or globally on the switch. To verify the DCBX configuration on a port, use the show interface dcbx detail command. dcbx version Configure the DCBX version...

Configure DCBX operation at the INTERFACE level on a switch or globally on the switch. To verify the DCBX configuration on a port, use the show interface dcbx detail command. debug dcbx Enable DCBX debugging. S6000 Syntax debug dcbx {all | auto-detect-timer | config-exchng | fail | mgmt | resource |...

Command Modes PROTOCOL LLDP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Intr...

Usage Information PFC and ETS settings are not pre-configured on Ethernet ports. You must use the dcb-map command to configure different groups of 802.1p priorities with PFC and ETS settings. Using the priority-pgid command, you assign each 802.1p priority to one priority group. A priority group con...

13 Debugging and Diagnostics The basic debugging and diagnostic commands are supported by the Dell Networking Operating System (OS) on the S6000 platform.This chapter contains the following sections: • Offline Diagnostic Commands• Buffer Tuning Commands• Hardware Commands Diagnostics and Monitoring ...

Offline Diagnostic Commands The offline diagnostics test suite is useful for isolating faults and debugging hardware. While tests are running, Dell Networking OS results are saved as a text file (TestReport-SU-X.txt) in the flash directory. This show file command is available only on master and stan...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Usage Information You cannot enter this command on a Master or Standby unit. The system re...

unit number counters Enter the keyword unit along with a port-pipe number, then the keyword counters to clear the counters on the selected port-pipe. The range is 0 to 0 for the S6000. cpu data-plane statistics Enter the keywords cpu data-plane statistics to clear the data plane statistics. cpu part...

port-set 0–0 counters Enter the keywords port-set along with a port-pipe number, then the keyword counters to clear the system-flow counters on the selected port-pipe. The range is 0 to 0 for the S6000. Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For c...

Version 7.8.1.0 Introduced on the S-Series. Usage Information This command enables a hardware watchdog mechanism that automatically reboots an Dell Networking OS switch/ router with a single unresponsive unit. This behavior is a last-resort mechanism intended to prevent a manual power cycle. show ha...

show hardware layer3 Display Layer 3 ACL or QoS data for the selected stack member and stack member port-pipe. S6000 Syntax show hardware layer3 {acl | qos} stack-unit number port-set 0–0 Parameters acl | qos Enter either the keyword acl or the keyword qos to select between ACL or QoS data. stack-un...

Related Commands clear hardware system-flow — clears the statistics from selected hardware components. show interfaces stack-unit — displays information on all interfaces on a specific S- Series stack member. show processes cpu (S-Series) — displays the CPU usage information based on the processes r...

Field Description Buffer Accounting Stats for Unit 0 Port 1 priority-group 0 Displays the counters that are calculated by the buffer statistics tracking method for each port per priority group on a particular stack member. Max Shared Limit Maximum shared buffer space allotted to the specific port fo...

14 Dynamic Host Configuration Protocol (DHCP) Dynamic host configuration protocol (DHCP) is an application layer protocol that dynamically assigns IP addresses and other configuration parameters to network end-stations (hosts) based on the configuration policies the network administrators determine....

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series. lease Specify a lease time for the addresses in a pool. S6000 Syntax lease {...

pool Create an address pool. S6000 Syntax pool name Parameters name Enter the address pool’s identifying name. Defaults none Command Modes DHCP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Refere...

Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series and S-Series. show ip dhcp configuration Display the DHCP configuration. S6000 Syntax show ip dhcp configuration [global | pool name ] Parameters pool name Display the config...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version...

Related Commands arp inspection — enables dynamic ARP inspection on a VLAN. clear ip dhcp snooping Clear the DHCP binding table. S6000 Syntax clear ip dhcp snooping binding Defaults none Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other...

Version 9.2.(0.0) Introduced on the S4810 and S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.1.0 Introduced on the E-Series. Version 8.2.1.0 Introduced on the C-Series and S-Series on Layer 2 interfaces. Version 7.8.1.0 Introduced on the C-Series and S-Series on Layer 3 interfaces. Us...

Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the E-Series. Version 7.8.1.0 Introduced on the C-Series and S-Series. ip dhcp snooping trust Configure an interface as trusted. S6000 Syntax [no] ip dhcp snooping trust Defaults Untruste...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version...

The following is a list of the Dell Networking OS version history for this command. Version 9.4.(0.0) Added support for VRF. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version ...

ip helper-address Configures the destination broadcast address or the host address for DHCP server requests. Syntax ip helper-address [vrf vrf-name ] ip-address To disable the destination broadcast address or the host address for DHCP server requests, use the ip helper-address [vrf vrf-name ] ip-add...

Defaults none Command Modes • EXEC• EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this comman...

ip host Configures a mapping between the host name server and the IP address for a specific VRF. This mapping information is used by the name-to-IP address table to resolve host names. Syntax ip host [vrf vrf-name] name ip-address To undo the host name server to IP address mapping for VRFs, use the ...

16 Flex Hash and Optimized Boot-Up This chapter describes the Flex Hash and fast-boot enhancements. load-balance ingress-port enable Enable the Flex hash functionality. This utility is supported on the S6000 platform. Syntax load-balance ingress-port enable To disable the Flex hash capability, use t...

17 FCoE Transit To enable the FCoE Transit feature and configure FIP snooping, use the following Dell Networking Operating System commands on the platform.In a converged Ethernet network, a switch can operate as an intermediate Ethernet bridge to snoop on FIP packets during the login process on Fibr...

clear fip-snooping statistics Clears the statistics on the FIP packets snooped on all VLANs, a specified VLAN, or a specified port interface. Syntax clear fip-snooping statistics [interface vlan vlan-id | interface port-type port/slot | interface port-channel port- channel-number ] Parameters vlan-i...

ifm Enter the keyword ifm for IFM-specific debugging. info Enter the keyword info for information-specific debugging. ipc Enter the keyword ipc for IPC-specific debugging. tx Enter the keyword tx for packet transmit-specific debugging. Command Modes EXEC Privilege Command History This guide is platf...

Version 8.3.12.0 Introduced on the S4810. Version 8.3.16.0 Introduced on MXL 10/40GbE Switch IO Module. Usage Information The maximum number of FCoE VLANs supported on the switch is eight. show fip-snooping config Display the FIP snooping status and configured FC-MAP values. Syntax show fip-snooping...

show fip-snooping enode Display information on the ENodes in FIP-snooped sessions, including the ENode interface and MAC address, FCF MAC address, VLAN ID and FC-ID. Syntax show fip-snooping enode [ enode-mac-address ] Parameters enode-mac-address Enter the MAC address of the ENodes to display. Comm...

show fip-snooping fcf Display information on the FCFs in FIP-snooped sessions, including the FCF interface and MAC address, FCF interface, VLAN ID, FC-MAP value, FKA advertisement period, and number of ENodes connected. Syntax show fip-snooping fcf [ fcf-mac-address ] Parameters fcf-mac-address Ente...

54:7f:ee:37:34:40 Po 22 100 0e:fc:00 4000 2 show fip-snooping statistics Display statistics on the FIP packets snooped on all interfaces, including VLANs, physical ports, and port channels. Syntax show fip-snooping statistics [interface vlan vlan-id | interface port-type port/slot | interface port-c...

Number of Multicast Discovery Solicits :0 Number of Unicast Discovery Solicits :0 Number of FLOGI :0 Number of FDISC :0 Number of FLOGO :0 Number of Enode Keep Alive :0 Number of VN Port Keep Alive :0 Number of Multicast Discovery Advertisement :4451 Number of Unicast Discovery Advertisement :2 Numb...

show fip-snooping vlan Display information on the FCoE VLANs on which FIP snooping is enabled. Syntax show fip-snooping vlan Command Modes • EXEC• EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS C...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series. Version 7.5.1.0 Introduced. Usage Information Executing this command without the optional...

Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced. mode Set the Master or Transit mode of the ring. S6000 Syntax mode {master | transit} To reset the mode, use the no mode {master | transit} command. Parameters master Enter the keyword ma...

protocol frrp Enter the Resilient Ring Protocol and designate a ring identification. S6000 Syntax protocol frrp { ring-id } To exit the ring protocol, use the no protocol frrp { ring-id } command. Parameters ring-id Enter the ring identification number. The range is from 1 to 255. Defaults none Comm...

Primary : GigabitEthernet 0/16 State: Forwarding Secondary: Port-channel 100 State: Blocking Control Vlan: 1 Ring protocol Timers: Hello-Interval 50 msec Dead-Interval 150 msec Ring Master's MAC Address is 00:01:e8:13:a3:19 Topology Change Statistics: Tx:110 Rx:45 Hello Statistics: Tx:13028 Rx:12348...

• VLANs created dynamically with GVRP exist only as long as a GVRP-enabled device is sending updates. If the devices no longer send updates, or GVRP is disabled, or the system is rebooted, all dynamic VLANs are removed. • GVRP manages the active topology, not non-topological data such as VLAN protoc...

Related Commands show gvrp statistics — displays the GVRP statistics. debug gvrp Enable debugging on GVRP. S6000 Syntax debug gvrp {config | events | pdu} To disable debugging, use the no debug gvrp {config | events | pdu} command. Parameters config Enter the keyword config to enable debugging on th...

disable Globally disable GVRP. S6000 Syntax disable To re-enable GVRP, use the no disable command. Defaults Enabled. Command Modes CONFIGURATION-GVRP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line ...

gvrp enable Enable GVRP on physical interfaces and LAGs. S6000 Syntax gvrp enable To disable GVRP on the interface, use the no gvrp enable command. Defaults Disabled. Command Modes CONFIGURATION-INTERFACE Command History This guide is platform-specific. For command information about other platforms,...

show garp timers Display the GARP timer settings for sending GARP messages. S6000 Syntax show garp timers Defaults none Command Modes • EXEC• EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Comman...

21 Internet Group Management Protocol (IGMP) The IGMP commands are supported by the Dell Networking operating software on the S6000 platform.This chapter contains the following sections: • IGMP Commands • IGMP Snooping Commands IGMP Commands Dell Networking OS supports IGMPv1/v2/v3 and is compliant ...

• For a VLAN interface, enter the keyword vlan then the slot/port information. The range is from 1 to 4094. • For a 1-Gigabit Ethernet interface, enter the keyword gigabitethernet followed by the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword tengigabitethernet then ...

Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 ...

ip igmp querier-timeout Change the interval that must pass before a multicast router decides that there is no longer another multicast router that should be the querier. Syntax ip igmp querier-timeout seconds To return to the default value, use the no ip igmp querier-timeout command. Parameters seco...

ip igmp query-interval Change the transmission frequency of IGMP general queries the Querier sends. S6000 Syntax ip igmp query-interval seconds To return to the default values, use the no ip igmp query-interval command. Parameters seconds Enter the number of seconds between queries sent out. The ran...

Version 7.5.1.0 Introduced on the E-Series. show ip igmp groups View the IGMP groups. S6000 Syntax show ip igmp groups [group-address [detail] | detail | interface [ group-address [detail]]] Parameters group-address (OPTIONAL) Enter the group address in dotted decimal format to view information on t...

Group Address Interface Mode Uptime Expires Last Reporter 225.0.0.0 Vlan 100 IGMPv2 00:00:05 00:02:04 3.0.0.51 Member Ports: Po 2* 225.0.0.1 Vlan 100 IGMPv2 00:00:05 00:02:04 3.0.0.51 Member Ports: Po 2* 225.0.0.2 Vlan 100 IGMPv2 00:00:05 00:02:04 3.0.0.51 Member Ports: Po 2* 225.0.0.3 Vlan 100 IGMP...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. Version 7.7.1.0 Introduced on the E-Series. Related Commands ip igmp ssm-map...

If the IP SA in the incoming IGMP general query frame is lower than the IP address of the VLAN interface, the switch disables its IGMP snooping Querier functionality. If the IP SA of the incoming IGMP general query is higher than the VLAN IP address, the switch continues to work as an IGMP snooping ...

ip igmp snooping fast-leave Enable IGMP snooping fast-leave for this VLAN. S6000 Syntax ip igmp snooping fast-leave To disable IGMP snooping fast leave, use the no igmp snooping fast-leave command. Defaults Not configured. Command Modes INTERFACE VLAN — (conf-if-vl- n ) Command History This guide is...

Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 ...

Command Modes INTERFACE VLAN — (conf-if-vl- n ) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. ...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Thi...

22 Interfaces The commands in this chapter are supported by Dell Networking operating software on the S6000 platform.This chapter contains the following sections: • Basic Interface Commands • Port Channel Commands This chapter contains the following sections: • Basic Interface Commands• Port Channel...

Related Commands mac learning-limit — allows aging of MACs even though a learning-limit is configured or disallow station move on learned MACs. show interfaces — displays information on the interfaces. clear dampening Clear the dampening counters on all the interfaces or just the specified interface...

Example Dell#clear dampening tegigabitethernet 1/2 Clear dampening counters on TeGi 1/2 [confirm] y Dell# Related Commands show interfaces dampening — displays interface dampening information. dampening — configures dampening on an interface. dampening Configure dampening on an interface. S6000 Synt...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-...

The tunnel interface operates as an ECMP (equal cost multi path) only when the next hop to the tunnel destination is over a physical interface. If you select any other interface as the next hop to the tunnel destination, the tunnel interface does not operate as an ECMP. Example Dell(conf)#int tengig...

gigabitethernet 0/1 - 5 ; interface group gigabitethernet 0/1-5 . • For a Gigabit Ethernet interface, enter the keyword gigabitethernet then the slot/port information. • For a 10-Gigabit Ethernet interface, enter the keyword TenGigabitEthernet then the slot/port information. • For a 40-Gigabit Ether...

Related Commands interface range – configures a range of command (bulk configuration) interface range macro name – runs an interface range macro. interface range macro name Run the interface-range macro to automatically configure the pre-defined range of interfaces. S6000 Syntax interface range macr...

Usage Information When you configure keepalive , the system sends a self-addressed packet out of the configured interface to verify that the far end of a WAN link is up. When you configure no keepalive , the system does not send keepalive packets and so the local end of a WAN link remains up even if...

Input giants: 0 0 pps 0 Input throttles: 0 0 pps 0 Input CRC: 0 0 pps 0 Input IP checksum: 0 0 pps 0 Input overrun: 0 0 pps 0 Output underruns: 0 0 pps 0 Output throttles: 0 0 pps 0 m - Change mode c - Clear screen l - Page up a - Page down T - Increase refresh interval t - Decrease refresh interval...

Input Statistics: ... User Information Both sides of the link must have auto-negotiation enabled or disabled for the link to come up. The following details the possible speed and auto-negotiation combinations for a line between two 10/100/1000 Base-T Ethernet interfaces. Port 0 • auto-negotiation en...

show interfaces configured Display any interface with a non-default configuration. S6000 Syntax show interfaces configured Command Modes • EXEC• EXEC Privilege Command History Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000...

Time since last interface status change: 00:04:59 Dell# Related Commands show interfaces — displays information on a specific physical interface or virtual interface. show interfaces dampening Display interface dampening information. S6000 Syntax show interfaces dampening [[ interface ] [summary] [d...

Example Dell#show interfaces stack-unit 0 GigabitEthernet 0/1 is down, line protocol is down Hardware is Force10Eth, address is 00:01:e8:4c:f2:82 Current address is 00:01:e8:4c:f2:82 Pluggable media not present Interface index is 34129154 Internet address is not set MTU 1554 bytes, IP MTU 1500 bytes...

Gi 0/11 Down Auto Auto -- Gi 0/12 Down Auto Auto -- Gi 0/13 Down Auto Auto -- Gi 0/14 Down Auto Auto -- Gi 0/15 Down Auto Auto - Dell# Related Commands show interfaces — displays information on a specific physical interface or virtual interface. show interfaces switchport Display only virtual and ph...

show interfaces transceiver — displays the physical status and operational status of an installed transceiver. The output also displays the transceiver’s serial number. show interfaces transceiver Display the physical status and operational status of an installed transceiver. The output also display...

SFP 1 RS state = False SFP 1 Tx Disable state = False =================================== SFP 1 Temperature High Alarm Flag = False SFP 1 Voltage High Alarm Flag = False SFP 1 Tx Bias High Alarm Flag = False SFP 1 Tx Power High Alarm Flag = False SFP 1 Rx Power High Alarm Flag = False SFP 1 Temperat...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.1 Introduced on the S4810. Usage Information Splitting a 40G port into 4x10G port is supported on standalone and stacked units.The quad port must be in a defaul...

show interfaces port-channel — displays information on configured Port Channel groups. show interfaces port-channel Display information on configured Port Channel groups. S6000 Syntax show interfaces port-channel [ channel-number ] [brief] Parameters channel-number For a Port Channel interface, ente...

Enhanced Validation of Interface Ranges This functionality is supported on the S6000 platform. You can avoid specifying spaces between the range of interfaces, separated by commas, that you configure by using the interface range command. For example, if you enter a list of interface ranges, such as ...

23 IPv4 Routing The basic IPv4 commands are supported by Dell Networking operating system on the S6000 platform. arp To associate an IP address with a MAC address in the switch, use address resolution protocol (ARP). S6000 Syntax arp [vrf vrf-name ] ip-address mac-address interface To remove an ARP ...

arp retries Set the number of ARP retries in case the system does not receive an ARP reply in response to an ARP request. S6000 Syntax arp retries number Parameters number Enter the number of retries. The range is from 1 to 20. The default is 5 . Defaults 5 Command Modes CONFIGURATION Command Histor...

clear host Remove one or all dynamically learned host table entries. S6000 Syntax clear host name Parameters name Enter the name of the host to delete. Enter * to delete all host table entries. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information abou...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.4(0.0) Added support for VRF. Version ...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.9.1.0 Introduced VRF on the E-Series. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on...

Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Int...

00:60:CF:20:7B:8C to 113.3.3.254 Dell# Related Commands ip helper-address – specifies the destination broadcast or host address for the DHCP server request. ip helper-address hop-count disable – disables the hop-count increment for the DHCP relay agent. debug ip icmp View information on the internal...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 8.2.1.0 Added support for 4094 VLANs on the E-Series Exa...

Usage Information To stop packets from flooding the user terminal when debugging is turned on, use the count option. The access-group option supports only the equal to ( eq ) operator in TCP ACL rules. Port operators not equal to ( neq ), greater than ( gt ), less than ( lt ), or range are not suppo...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced fo...

ip proxy-arp Enable proxy ARP on an interface. S6000 Syntax ip proxy-arp To disable proxy ARP, use the no ip proxy-arp command. Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Network...

management route Configure a static route that points to the Management interface or a forwarding router. S6000 Syntax management route {{ ip-address mask | { ipv6-address prefix- length }} { forwarding-router-address | managementethernet} To remove a static route, use the no management route{{ ip-a...

pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information When a static route (or a protocol route) overlaps with Management static route, the static route (or a protocol route) is preferred over the Management Static route. Also, Management static routes and the Management Connected prefix ...

show ip cam stack-unit Display CAM entries for a port-pipe of a stack-unit on a S-Series or Z-Series switch. S6000 Syntax show ip cam stack-unit { id } [port-set { pipe-number } | vrf vrf- name { ip-address mask [longer-prefixes [ecmp-group detail]]}| ecmp-group {detail | member-info [detail [group-...

1.1.1.2/32 0 0 1000 00:01:00:00:00:02 Te 7/42 - 2.1.1.2/32 0 0 20 00:03:00:00:00:02 Po 10 - 2.1.1.1/32 0 1 0 00:00:00:00:00:00 CP - 1.1.1.1/32 0 1 0 00:00:00:00:00:00 CP - 2.1.1.0/24 0 1 0 00:00:00:00:00:00 CP - 1.1.1.0/24 0 1 0 00:00:00:00:00:00 CP - 100.1.1.0/24 1 0 20 00:03:00:00:00:02 Po 10 0 10...

show ip interface View IP-related information on all interfaces. S6000 Syntax show ip interface [ interface | brief] [configured] Parameters interface (OPTIONAL)Enter the following keywords and slot/port or number information, the valid range of slot number is from 0 to 5: • For a Loopback interface...

Usage Information The following describes the show ip interface brief command shown in the following example. Fields Description Interface Displays type of interface and the associated slot and port number. IP-Address Displays the IP address for the interface, if configured. Ok? Indicates if the har...

summary (OPTIONAL) Enter the keyword summary to view a table listing the number of active and non-active routes and their sources. static (OPTIONAL) Enter the keyword static to view non-active routes also. Command Modes • EXEC• EXEC Privilege Command History This guide is platform-specific. For comm...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.6.1.0 Regular evaluation optimization enabled/disabled added to displa...

Destination Gateway Dist/Metric Last Change ----------- ------- ----------- ----------- C 13.0.0.0/24 Direct, Te 0/17 0/0 00:00:04 show ip route list Display IP routes in an IP prefix list. S6000 Syntax show ip route vrf vrf-name list prefix-list Parameters prefix-list Enter the name of a configured...

N2- OSPF NSSA external type 2, E1 - OSPF external type 1, E2- OSPF external type 2, i - IS-IS, L1 - IS-IS level-1, L2- IS-IS level-2, IA - IS-IS inter area, * - candidate default, >- non-active route, + - summary route Gateway of last resort is not set Destination Gateway Dist/Metric Last Change ...

show ip traffic View IP, ICMP, UDP, TCP and ARP traffic statistics. S6000 Syntax show ip traffic [all | cp | rp1 | rp2] NOTE: These options are supported only on the E-Series. Parameters all (OPTIONAL) Enter the keyword all to view statistics from all processors. If you do not enter a keyword, you a...

• ARP Statistics: Rcvd: Replies: Object = f10ArpReplyRecv, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.3 • ARP Statistics: Sent: Request: Object = f10ArpReqSent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.2 • ARP Statistics: Sent: Replies: Object = f10ArpReplySent, OIDs = 1.3.6.1.4.1.6027.3.3.5.2.4 • ARP Statistics: Sent:...

-- Line card 4 -- Current Settings(in block sizes) L2Acl : 2 Ipv4Acl : 2 Ipv6Acl : 4 Ipv4Qos : 2 L2Qos : 3 Dell#show cam-acl Related Commands cam-acl — configures CAM profiles to support IPv6 ACLs. permit icmp To allow all or specific internet control message protocol (ICMP) messages, configure a fi...

26 Intermediate System to Intermediate System (IS-IS) The intermediate system to intermediate system (IS-IS) protocol for IPv4 and IPv6 is supported on the S6000platform.IS-IS is an interior gateway protocol that uses a shortest-path-first algorithm. IS-IS facilitates the communication between open ...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.5.1.0 Introduced on the E-Series. Usage Information To perform protocol-support consistency checks on hello packets, use this command. The adjacency-check is enabl...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Usage Information To prevent the link state database from receiving incorrect routing information from unauthorized routers, use the area-password command on routers within ...

clear isis Restart the IS-IS process. All IS-IS data is cleared. S6000 Syntax clear isis [ tag ] {* | database | traffic} Parameters tag (Optional) Enter an alphanumeric string to specify the IS-IS routing tag area. * Enter the keyword * to clear all IS-IS information and restart the IS-IS process. ...

Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Usage Information Entering debug isis enables all debugging parameters. To display all debugging information in one output, use this command. To turn off debugging, you normally enter separate no forms of each comman...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. debug isis local-updates To debug IS-IS local update packets, enable debugging on a specific interface and provides diagnostic information. S6000 Syntax debug isis local-upda...

Version 8.3.12.0 Introduced on the S4810. Version 6.3.1.0 Introduced. debug isis snp-packets To debug IS-IS complete sequence number PDU (CSNP) and partial sequence number PDU (PSNP) packets, enable debugging on a specific interface and provides diagnostic information. S6000 Syntax debug isis snp-pa...

Version 6.3.1.0 Introduced. debug isis spf-triggers Enable debugging on the events that triggered IS-IS shortest path first (SPF) events for debugging purposes. S6000 Syntax debug isis spf-triggers To turn off debugging, use the no debug isis spf-triggers command. Command Modes EXEC Privilege Comman...

• For a 40-Gigabit Ethernet interface, enter the keyword fortyGigE then the slot/port information. • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet the slot/port information. • For a Port Channel interface, enter the keywords port- channel then a number. The range is from 1 to 1...

Related Commands graceful-restart restart-wait — enables the graceful restart maximum wait time before a restarting peer comes up. hello padding Use to turn ON or OFF padding for LAN and point-to-point hello PDUs or to selectively turn padding ON or OFF for LAN or point-to-point hello PDUs. S6000 Sy...

Command Modes ROUTER ISIS Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introd...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 7.5.1.0 Introduced. Usage Information To assign a network entity title to enable IS-IS, use the net command. Related Commands • net — configures an IS-IS network ent...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Usage Information Hello packets are held for a length of three times the value of the hello interval. To conserve bandwidth and CPU usage, use a high hello interval seconds....

show isis database Display the IS-IS link state database. S6000 Syntax show isis database [level-1 | level-2] [local] [detail | summary] [ lspid ] Parameters level-1 (OPTIONAL) Displays the Level 1 IS-IS link-state database. level-2 (OPTIONAL) Displays the Level 2 IS-IS link-state database. local (O...

ISIS.00-00 * 0x00000006 0xCF43 580 0/0/0 ! FTOS#show isis database detail ISIS.00-00 IS-IS Level-1 Link State Database LSPID LSP Seq Num LSP Checksum LSP Holdtime ATT/P/OL ISIS.00-00 * 0x0000002B 0x853B 1075 0/0/0 Area Address: 49.0000.0001 NLPID: 0xCC 0x8E IP Address: 10.1.1.1 IPv6 Address: 1011::1...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version...

The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Example FTOS#show isis hostname System Id Dynami...

Version 9.2(0.2) Introduced on the Z9000. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.12.0 Introduced on the S4810. Example FTOSF>show isis int GigabitEthernet 0/7 is up, line protocol is up MTU 1497, Encapsulation SAP Routing Protocol: IS-IS Ci...

Field Description Circuit Id The neighbor’s interpretation of the designated router for the interface. Example The bold sections below identify that Multi-Topology IS-IS is enabled. FTOS#show isis neighbors System Id Interface State Type Priority Uptime Circuit Id TEST Gi 7/1 Up L1L2 (M) 127 09:28:0...

System Id: F100.E120.0013 IS-Type: level-1-2 Manual area address(es): 49.0000.0001 Routing for area address(es): 49.0000.0001 Interfaces supported by IS-IS: GigabitEthernet 1/0 - IP - IPv6 GigabitEthernet 1/1 - IP - IPv6 GigabitEthernet 1/10 - IP - IPv6 Loopback 0 - IP - IPv6 Redistributing: Distanc...

27 Link Aggregation Control Protocol (LACP) This chapter contains commands for Dell Networks’s implementation of the link aggregation control protocol (LACP) for creating dynamic link aggregation groups (LAGs) — known as “port-channels” in the Dell Networking operating software. The LACP commands in...

Version 6.2.1.1 Introduced on the E-Series. Related Commands show lacp — displays the LACP configuration. debug lacp Debug LACP (configuration, events, and so on). S6000 Syntax debug lacp [config | events | pdu [ interface-type [in | out]]] To disable LACP debugging, use the no [config | events | pd...

Command Modes • EXEC• EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0...

show config Display the current configuration of the selected VLAN. S6000 Syntax show config Command Modes INTERFACE VLAN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The follow...

Example (OpenFlow instance) NUM Status Description Q Ports * 1 Inactive 3 Inactive O 6 Inactive O 8 Inactive O 12 Inactive O Te 0/10 Related Commands vlan-stack compatible — enables the Stackable VLAN feature on the selected VLAN. interface vlan — configures a VLAN. tagged Add a Layer 2 interface to...

Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Usage Information When you use the no tagged command, the interface is automatically placed in the Default VLAN as an untag...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Intr...

debug fefd Enable debugging of FEFD. S6000 Syntax debug fefd {events | packets} [ interface ] To disable debugging of FEFD, use the no debug fefd {events | packets} [ interface ] command. Parameters events Enter the keyword events to enable debugging of FEFD state changes. packets Enter the keyword ...

fefd Enable Far-End Failure Detection on an interface, set the FEFD interval, or select the FEFD mode. S6000 Syntax fefd {disable|interval|mode { aggressive | normal } Parameters disable Enter the keyword disable to disable FEFD for the specified interface. interval Enter the keyword interval , foll...

Related Commands • fefd disable — disables far-end failure detection on an interface. • fefd reset — enables FEFD globally on the system. • fefd mode — changes FEFD mode on an interface. fefd disable Disable FEFD on an interface only. This command overrides the fefd reset command for the interface. ...

Parameters seconds Enter a number as the time between FEFD control packets. The range is from 3 to 300 seconds. The default is 15 seconds . Defaults 15 seconds Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevan...

Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 8.3.19.0 Introdu...

If you disable FEFD globally ( no fefd-global ), the system does not remove the FEFD interface configuration. Related Commands • fefd — enables far-end failure detection. • fefd-global interval — configures an interval between FEFD control packets. • show fefd — shows the FEFD command output. show f...

29 Link Layer Discovery Protocol (LLDP) The link layer discovery protocol (LLDP) advertises connectivity and management from the local station to the adjacent stations on an IEEE 802 LAN.This chapter contains the following sections: • LLPD Commands • LLDP-MED Commands LLDP facilitates multi-vendor i...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series. Version 7.4.1.0 I...

Version 7.4.1.0 Introduced on the E-Series. debug lldp interface To display timer events, neighbor additions or deletions, and other information about incoming and outgoing packets, enable LLDP debugging. S6000 Syntax debug lldp interface { interface | all}{events | packet {brief | detail} {tx | rx ...

show lldp neighbors Display LLDP neighbor information for all interfaces or a specified interface. S6000 Syntax show lldp neighbors [ interface ] [detail] Parameters interface (OPTIONAL) Enter the following keywords and slot/port or number information: • For a Fast Ethernet interface, enter the keyw...

Usage Information Omitting the keyword detail displays only the remote chassis ID, Port ID, and Dead Interval. Example R1(conf-if-gi-1/31)#do show lldp neighbors Loc PortID Rem Host Name Rem Port Id Rem Chassis Id -------------------------------------------------------------- Gi 1/21 R2 GigabitEther...

The E-Series generally supports the commands. However, LLDP-MED commands are more useful on the C-Series and the S50V model of the S-Series, because they support Power over Ethernet (PoE) devices. As defined by ANSI/TIA-1057, LLDP-MED provides organizationally specific TLVs (Type Length Value), so t...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.7.1.0 Introduced on the S-Series. Version 7.6.1.0 Introduced on the C-Series and E-Series. Related Commands debug lldp interface — debugs LLDP. show lldp neighbors ...

Usage Information Advertise the Extended Power via MDI on all ports that are connected to an 802.3af powered, LLDP-MED endpoint device. Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. advertise med softphone-voice To advertise softphone to enab...

Related Commands debug lldp interface — debugs LLDP. show lldp neighbors — displays the LLDP neighbors. advertise med streaming-video To advertise streaming video services for broadcast or multicast-based video, configure the system. This command does not include video applications that rely on TCP ...

show lldp neighbors — displays the LLDP neighbors. advertise med video-conferencing To advertise dedicated video conferencing and other similar appliances that support real-time interactive video, configure the system. S6000 Syntax advertise med video-conferencing { vlan-id layer2_priority DSCP_valu...

advertise med video-signaling To advertise video control packets that use a separate network policy than video data, configure the system. S6000 Syntax advertise med video-signaling { vlan-id layer2_priority DSCP_value } | {priority-tagged number } To return to the default, use the no advertise med ...

advertise med voice To advertise a dedicated IP telephony handset or other appliances supporting interactive voice services, configure the system. S6000 Syntax advertise med voice { vlan-id layer2_priority DSCP_value } | {priority-tagged number } To return to the default, use the no advertise med vo...

advertise med voice-signaling To advertise when voice control packets use a separate network policy than voice data, configure the system. S6000 Syntax advertise med voice-signaling { vlan-id layer2_priority DSCP_value } | {priority-tagged number } To return to the default, use the no advertise med ...

30 Microsoft Network Load Balancing This functionality is supported on the S6000 platform. Network Load Balancing (NLB) is a clustering functionality that is implemented by Microsoft on Windows 2000 Server and Windows Server 2003 operating systems. NLB uses a distributed methodology or pattern to eq...

response with MAC-s4 is received as the last one). The interface associated with server, S4, is added to the ARP table. • With NLB feature enabled, after learning the NLB ARP entry, all the subsequent traffic is flooded on all ports in VLAN1. With NLB, the data frame is forwarded to all the servers ...

learned, traffic is forwarded to only one server rather than the entire cluster, and failover and balancing are not preserved. To preserve failover and balancing, the switch forwards the traffic destined for the server cluster to all member ports in the VLAN connected to the cluster. To ensure that ...

31 Multicast Source Discovery Protocol (MSDP) Multicast source discovery protocol (MSDP) connects multiple PIM Sparse-Mode (PIM-SM) domains together.MSDP peers connect using TCP port 639. Peers send keepalives every 60 seconds. A peer connection is reset after 75 seconds if no MSDP packets are recei...

clear ip msdp sa-cache Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. S6000 Syntax clear ip msdp sa-cache [ group-address | rejected-sa | local] Parameters group-address Enter the group IP address in dotted ...

clear ip msdp statistic Clears the entire source-active cache, the source-active entries of a particular multicast group, rejected, or local source-active entries. S6000 Syntax clear ip msdp sa-cache [ group-address | rejected-sa | local] Parameters group-address Enter the group IP address in dotted...

not part of the mesh-group. However, member X cannot forward the SA message to other members of the mesh-group. ip msdp originator-id Configure the MSDP Originator ID. S6000 Syntax ip msdp originator-id { interface } To remove the originator-id, use the no ip msdp originator-id { interface } command...

Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 6.2.1.1 Introduced ip msdp peer Configure an MSDP peer. S6000 Syntax ip msdp peer peer address [connect-source] [description] [sa- limit number ] To remove the MSDP peer, use the no ip msdp peer peer address [connect-source...

Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Intr...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.5.1.0 Introduced on the E-Series. Usage Information Dell Networking OS counts the SA messages originated by itself and those messages received from the MSDP peers. ...

Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 6.2.1.1 Introduced ip multicast-msdp Enable MSDP. S6000 Syntax ip multicast-msdp To exit MSDP, use the no ip multicast-msdp command. Defaults Not configured. Command Modes CONFIGURATION Command History This gu...

32 Multiple Spanning Tree Protocol (MSTP) Multiple spanning tree protocol (MSTP), as implemented by the Dell Networking operating system, conforms to IEEE 802.1s.This command supports the Dell Networking S6000 platform. debug spanning-tree mstp Enable debugging of the multiple spanning tree protocol...

show config View the current configuration for the mode. Only non-default values are shown. S6000 Syntax show config Command Modes MULTIPLE SPANNING TREE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command L...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version...

33 Multicast The multicast commands are supported by Dell Networking operating system (OS) on all S6000 platform.This chapter contains the following sections: • IPv4 Multicast Commands IPv4 Multicast Commands The following section contains the IPv4 multicast commands. clear ip mroute Clear learned m...

Related Commands ip pim sparse-mode — enables IGMP and PIM on an interface. show ip mroute View the multicast routing table. S6000 Syntax show ip mroute [static | group-address [ source-address ] | count | snooping [vlan vlan-id ] [ group-address [ source-address ]] | summary | vlt [ group-address [...

show ip rpf View reverse path forwarding. S6000 Syntax show ip rpf Command Modes • EXEC• EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of t...

34 Open Shortest Path First (OSPFv2 and OSPFv3) Open Shortest Path First version 2 for IPv4 is supported on S6000 Dell Networking Operating System (OS) platform. Open Shortest Path First version 3 (OSPFv3) for IPv6 is supported on the platform.OSPF is an Interior Gateway Protocol (IGP), which means ...

Defaults cost = 1 ; no areas are configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version his...

no-summary (OPTIONAL) Specify that no summary LSAs should be sent into the NSSA. Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . ...

Defaults Not configured. Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this comman...

Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. clear ip ospf statistics Clear the packet statistics in interfaces and neighbors. S6000 Syntax clear ip ospf [ process-id ] [vrf vrf-name ] statistics [interface na...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for the Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on t...

Parameters weight Specify an administrative distance. The range is from 1 to 255. The default is 110 . ip-address (OPTIONAL) Enter a router ID in the dotted decimal format. If you enter a router ID, include the mask for that router address. mask (OPTIONAL) Enter a mask in dotted decimal format or /n...

graceful-restart helper-reject Specify the OSPF router to not act as a helper during graceful restart. S6000 Syntax graceful-restart helper-reject ip-address To return to default value, use the no graceful-restart helper-reject command. Parameters ip-address Enter the OSPF router-id, in IP address f...

To disable graceful restart mode, use the no graceful-restart mode command. Parameters planned-only (OPTIONAL) Enter the keywords planned-only to indicate graceful restart is supported in a planned restart condition only. unplanned-only (OPTIONAL) Enter the keywords unplanned-only to indicate gracef...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Serie...

ip ospf dead-interval Set the time interval since the last hello-packet was received from a router. After the interval elapses, the neighboring routers declare the router dead. S6000 Syntax ip ospf dead-interval seconds To return to the default values, use the no ip ospf dead-interval command. Param...

Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduc...

Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. ip ospf priority To determi...

Use this command for interfaces connected to multi-access networks, not point-to-point networks. ip ospf retransmit-interval Set the retransmission time between lost link state advertisements (LSAs) for adjacencies belonging to the interface. S6000 Syntax ip ospf retransmit-interval seconds To retur...

network area Define which interfaces run OSPF and the OSPF area for those interfaces. S6000 Syntax network ip-address mask area area-id To disable an OSPF area, use the no network ip-address mask area area- id command. Parameters ip-address Specify a primary or secondary address in dotted decimal fo...

• 2 = for OSPF External type 2 route-map map-name (OPTIONAL) Enter the keywords route-map then the name of the route map. tag tag-value (OPTIONAL) Enter the keyword tag to set the tag for routes redistributed into OSPF. The range is from 0 to 4294967295. Defaults none Command Modes ROUTER OSPF Comma...

Example Dell(conf)#router ospf 2 Dell(conf-router_ospf)# show config Display the non-default values in the current OSPF configuration. S6000 Syntax show config Command Modes ROUTER OSPF Command History This guide is platform-specific. For command information about other platforms, refer to the relev...

Line Beginning with Description “Min LSA....” Displays the intervals set for LSA transmission and acceptance. “Number of...” Displays the number and type of areas configured for this process ID. Example Dell#show ip ospf 10 Routing Process ospf 10 with ID 1.1.1.1 Virtual router default- vrf Supports...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.4.(0.0) Added support for VRF. Version...

Field Description Checksum Displays the Fletcher checksum of an LSA’s complete contents. Link count Displays the number of interfaces for that router. Example Dell>show ip ospf 1 database OSPF Router with ID (11.1.2.1) (Process ID 1) Router (Area 0.0.0.0) Link ID ADV Router Age Seq# Checksum Link...

show ip ospf database external Display information on the AS external (type 5) LSAs. S6000 Syntax show ip ospf [ process-id | vrf vrf-name] database external [ link-state-id ] [adv-router ip-address ] Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is ent...

OSPF Router with ID (20.20.20.5) (Process ID 1) Type-5 AS External LS age: 612 Options: (No TOS-capability, No DC, E) LS type: Type-5 AS External Link State ID: 12.12.12.2 Advertising Router: 20.31.3.1 LS Seq Number: 0x80000007 Checksum: 0x4cde Length: 36 Network Mask: /32 Metrics Type: 2 TOS: 0 Met...

show ip ospf database nssa-external Display NSSA-External (type 7) LSA information. S6000 Syntax show ip ospf [ process-id | vrf vrf-name ] database nssa-external [ link-state-id ] [adv-router ip-address ] Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID i...

Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. Related Commands show ip ospf database — displays OSPF database information. show ip ospf database opaque-area Display the opaque-area (type 10) LSA information. S6...

Options: (No TOS-capability, No DC, E) LS type: Type-10 Opaque Link Area Link State ID: 1.0.0.1 Advertising Router: 10.16.1.160 LS Seq Number: 0x80000416 Checksum: 0x376 Length: 28 Opaque Type: 1 Opaque ID: 1 Unable to display opaque data LS age: 833 Options: (No TOS-capability, No DC, E) LS type: T...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version...

Command Modes • EXEC• EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.4...

Number of TOS metric: 0 TOS 0 Metric: 1 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.142.2 (Link Data) Router Interface address: 192.68.142.2 Number of TOS metric: 0 TOS 0 Metric: 1 Link connected to: a Transit Network (Link ID) Designated Router address: 192.68.1...

show ip ospf interface Display the OSPF interfaces configured. If OSPF is not enabled on the switch, no output is generated. S6000 Syntax show ip ospf [ process-id | vrf vrf-name ] interface [ interface ] Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is...

Neighbor Count is 1, Adjacent neighbor count is 1 Adjacent with neighbor 192.168.253.1 (Backup Designated Router) GigabitEthernet 13/23 is up, line protocol is up Internet Address 192.168.0.1/24, Area 0.0.0.1 Process ID 1, Router ID 192.168.253.2, Network Type BROADCAST, Cost: 1 Transmit Delay is 1 ...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Added support for Multi-Process OSPF. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced o...

show ip ospf timers rate-limit Show the LSA currently in the queue waiting for timers to expire. S6000 Syntax show ip ospf [ process-id | vrf vrf-name ] timers rate-limit Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to ...

show ip ospf topology Display routers in directly connected areas. S6000 Syntax show ip ospf [ process-id | vrf vrf-name ] topology Parameters process-id Enter the OSPF Process ID to show a specific process. If no Process ID is entered, command applies only to the first OSPF process. vrf vrf-name En...

Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. Usage Information Setting the delay and holdtime parameters to a low number enables the switch to an alternate path quickly but requires more CPU usage. timers throttle lsa all Configure LSA transmit interval...

Version 8.4.2.1 Introduced on the C-Series and S-Series. Version 8.4.2.0 Introduced on the E-Series TeraScale. Version 7.5.1.0 Introduced on the E-Series ExaScale. redirect Configure a rule for the redirect list. S6000 Syntax redirect { ip-address | slot/port } { ip-protocol-number | protocol-type [...

• range = inclusive range of ports (you must specify two ports for the port command parameter.) source port Enter the keywords source-port then the port number to be matched in the ACL rule in the ICAP rule destination-port Enter the keywords destination-port then the port number to be matched in th...

36 PIM-Sparse Mode (PIM-SM) The protocol-independent multicast (PIM) commands are supported by the Dell Networking operating software on the S6000platform. IPv4 PIM-Sparse Mode Commands The following describes the IPv4 PIM-sparse mode (PIM-SM) commands. clear ip pim rp-mapping The bootstrap router (...

clear ip pim tib Clear PIM tree information from the PIM database. S6000 Syntax clear ip pim tib [ group ] Parameters group (OPTIONAL) Enter the multicast group address in dotted decimal format (A.B.C.D). Command Modes EXEC Privilege Command History This guide is platform-specific. For command infor...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.8.1.0 Introduced on the C-Series for the port-channels and the S-Serie...

Version 8.3.12.0 Introduced on the S4810. Version 8.1.1.0 Introduced on the E-Series ExaScale. Usage Information This command is applicable to last hop routers on the shared tree towards the rendezvous point (RP). show ip pim bsr-router View information on the Bootstrap router. S6000 Syntax show ip ...

Field Description Interface List the interface type, with either slot/port information or ID (VLAN or Port Channel), on which the PIM neighbor was found. Uptime/expires Displays the amount of time the neighbor has been up then the amount of time until the neighbor is removed from the multicast routi...

Version 8.3.7.0 Introduced on the S4810. Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. Example Dell(conf-mon-sess-1)#sh...

Version 8.3.11.1 Introduced on the Z9000. Version 8.1.1.0 Introduced on the E-Series ExaScale. Version 7.7.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Introduced on the E-Series. Example Dell#show monitor session SessID Source Destination Dir Mode Sour...

38 Private VLAN (PVLAN) The private VLAN (PVLAN) feature of the Dell Networking operating software is supported on the S6000 platforms.Private VLANs extend the Dell Networking OS security suite by providing Layer 2 isolation between ports within the same private VLAN. A private VLAN partitions a tra...

protocol spanning-tree pvst To enable PVST+ on a device, enter the PVST+ mode. S6000 Syntax protocol spanning-tree pvst To disable PVST+, use the disable command. Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms,...

show spanning-tree pvst View the Per-VLAN spanning tree configuration. S6000 Syntax show spanning-tree pvst [vlan vlan-id] [brief] [guard] Parameters vlan vlan-id (OPTIONAL) Enter the keyword vlan then the VLAN ID. The range is 1 to 4094. brief (OPTIONAL) Enter the keyword brief to view a synopsis o...

40 Quality of Service (QoS) The Dell Networking operating software commands for quality of service (QoS) include traffic conditioning and congestion control. QoS commands are not universally supported on all Dell Networking Products.S6000 platform.This chapter contains the following sections: • Glob...

Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Int...

Usage Information After you configure a unicast queue as strict-priority, that particular queue, on the entire chassis, is treated as a strict-priority queue . Traffic for a strict priority is scheduled before any other queues are serviced. For example, if you send 100% line rate traffic over the SP...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.1 Introduced on the E-Series. Usage Information The dot1p-priority comm...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version...

dot1p Queue ID 0 2 1 0 2 1 3 3 4 4 5 5 6 6 7 7 Command Modes • INTERFACE• CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networki...

description Add a description to the selected policy map or QoS policy. S6000 Syntax description { description } To remove the description, use the no description { description } command. Parameters description Enter a description to identify the policies (80 characters maximum). Defaults none Comma...

match ip dscp Use a differentiated services code point (DSCP) value as a match criteria. S6000 Syntax match {ip | ipv6 | ip-any} dscp dscp-list [set-ip-dscp value ] To remove a DSCP value as a match criteria, use the no match {ip | ipv6 | ip-any} dscp dscp-list [[multicast] set-ip-dscp value ] comma...

Up to 64 IP DSCP values can be matched in one match statement. For example, to indicate IP DCSP values 0 1 2 3 4 5 6 7, enter either the match ip dscp 0,1,2,3,4,5,6,7 or match ip dscp 0-7 command. NOTE: Only one of the IP DSCP values must be a successful match criterion, not all of the specified IP ...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. The match ip precedence comman...

Version 7.5.1.0 Added support for the DSCP Marking option. pre-Version 7.4.1.0 Introduced. Usage Information To access this command, enter the class-map command. After the class map is identified, you can configure the match criteria. Related Commands class-map — identifies the class map. match mac ...

Usage Information There are eight queues per interface on the S6000 and four queues on the S-Series. This command assigns a class map or QoS policy to different queues. Related Commands class-map — identifies the class map. service-policy input — applies an input policy map to the selected interface...

show qos qos-policy-output View the output QoS policy details. S6000 Syntax show qos qos-policy-output [ qos-policy-name ] Parameters qos-policy-name Enter the QoS policy name. Defaults none Command Modes • EXEC• EXEC Privilege Command History This guide is platform-specific. For command information...

Pre-Defined WRED Profile Name Minimum Threshold Maximum Threshold Maximum Drop Rate wred_drop 0 0 100 wred_teng_y 594 5941 100 wred_teng_g 594 5941 50 wred_fortyg_y 594 5941 50 wred_fortyg_g 594 5941 25 Related Commands wred-profile — creates a WRED profile. trust Specify dynamic classification (DSC...

Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 7.4.1.0 Added dot1p and IPv6 DSCP . pre-Version 6.1.1.1 Introduced on the E-Series Usage Information When you configure trust , matched bytes/packets counters are not incremented in the show qos statistic...

To stop marking packets, use the no wred ecn command. Defaults none Command Modes CONFIGURATION (conf-qos-policy-out) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following ...

DSCP Color Map Commands The DSCP color map allows you to set the number of specific DSCP values to yellow or red. Traffic marked as yellow delivers traffic to the egress queue which will either transmit the packet if it has available bandwidth or drop the packet due to no ability to send. Traffic ma...

clear ip rip Update all the RIP routes in the Dell Networking OS routing table. S6000 Syntax clear ip rip Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide...

ip poison-reverse Set the prefix of the RIP routing updates to the RIP infinity value. S6000 Syntax ip poison-reverse To disable poison reverse, use the no ip poison-reverse command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information a...

2 (OPTIONAL) Enter the number 2 for RIP version 2. Defaults RIPv1 and RIPv2 Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the D...

show ip rip database Display the routes that RIP learns. If the switch learned no RIP routes, no output is generated. S6000 Syntax show ip rip database [ ip-address mask ] Parameters ip-address (OPTIONAL) Specify an IP address in dotted decimal format to view RIP information on that network only. If...

Example show running-config rip ! router rip distribute-list Test1 in distribute-list Test21 out network 10.0.0.0 passive-interface GigabitEthernet 2/0 neighbor 20.20.20.20 redistribute ospf 999 version 2 timers basic Manipulate the RIP timers for routing updates, invalid, holddown times, and flush ...

Command Modes ROUTER RIP Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introdu...

42 Remote Monitoring (RMON) The Dell Networking operating software remote monitoring (RMON) is implemented on the S6000 platform.Dell Networking OS RMON is based on IEEE standards, providing both 32-bit and 64-bit monitoring and long-term statistics collection. Dell Networking OS RMON supports the f...

Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. rmon collection history Enable the RMON MIB history group of statistics collection on...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. rmon collection statistics Enable RMON MIB...

Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Introduced on the E-Series. rmon event Add an event in the RMON event table. S6000 Syntax rmon event number [log] [trap community ] [description string ] To disable RMON on an interface, use the no rmon event number command. Parameters numb...

The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Versi...

show rmon events Display the contents of the RMON event table. S6000 Syntax show rmon events [ index ] [brief] Parameters index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON event table in an easy-to-read format. Defa...

show rmon history Display the contents of the RMON Ethernet history table. S6000 Syntax show rmon history [ index ] [brief] Parameters index (OPTIONAL) Enter the table index number to display just that entry. brief (OPTIONAL) Enter the keyword brief to display the RMON Ethernet history table in an e...

9002 134529054 TenGigabitEthernet 3/0 9003 134791198 TenGigabitEthernet 3/1 9004 134791198 TenGigabitEthernet 3/1 Dell# show rmon log Display the contents of the RMON log table. S6000 Syntax show rmon log [ index ] [brief] Parameters index (OPTIONAL) Enter the table index number to display just that...

Example (Brief) Dell#show rmon log br eventIndex description ------------------------------ 2 2 4 4 Dell# show rmon statistics Display the contents of RMON Ethernet statistics table. S6000 Syntax show rmon statistics [index] [brief] Parameters index (OPTIONAL) Enter the table index number to display...

Related Commands protocol spanning-tree rstp — enters rapid spanning tree mode. debug spanning-tree rstp Enable debugging of RSTP and view information on the protocol. S6000 Syntax debug spanning-tree rstp [all | bpdu interface {in | out} | events] To disable debugging, use the no debug spanning-tre...

show config View the current configuration for the mode. Only non-default values are displayed. S6000 Syntax show config Command Modes CONFIGURATION RSTP (conf-rstp) Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking ...

44 Security Most of the commands in this chapter are available on the S6000 platform.This chapter contains various types of security commands offered in the Dell Networking operating software. The commands are listed in the following sections: • AAA Accounting Commands • Authorization and Privilege ...

Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.3.1.0 Introduced on the E-Series. Usage Information In the example above, TACACS+ accounting is used to track all usage of EXEC command and commands on privilege...

Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.3.1.0 Introduced on the E-Series. Usage Information Dell Networking OS issues accounting records for all users on the s...

interface tengigabitethernet 0/36 Dell(conf)#exit Dell(conf)#aaa radius group group1 show accounting Display the active accounting sessions for each online user. S6000 Syntax show accounting Defaults none Command Modes EXEC Command History This guide is platform-specific. For command information abo...

Authorization and Privilege Commands To set command line authorization and privilege levels, use the following commands. authorization Apply an authorization method list to terminal lines. S6000 Syntax authorization { exec | commands { level | role role-name }} method-list Parameters exec Enter the ...

Related Commands aaa authorization commands — sets the parameters that restrict (or permit) a user’s access to EXEC and CONFIGURATION level commands aaa authorization exec — sets the parameters that restrict (or permit) a user’s access to EXEC level commands. aaa authorization commands Set parameter...

Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.1.1.0 Added support for RADIUS. aaa authorization config-commands Set parameters that restrict (or permit) a user’s acc...

aaa authorization exec Set parameters that restrict (or permit) a user’s access to EXEC-level commands. S6000 Syntax aaa authorization exec { name | default} {local || tacacs+ || if-authenticated || none} To disable authorization checking for EXEC level commands, use the no aaa authorization exec co...

Usage Information To define a password for the level to which you are assigning privilege or access, use the enable password command. privilege level (LINE mode) Change the access level for users on the terminal lines. S6000 Syntax privilege level level To delete access to a terminal line, use the n...

aaa authentication enable Configure AAA Authentication method lists for user access to EXEC privilege mode (the “Enable” access). S6000 Syntax aaa authentication enable {default | method-list-name } method [ ... method2 ] To return to the default setting, use the no aaa authentication enable {defaul...

Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. Version 6.2.1.0 Introduced on the E-Series. Usage Information By default, the Enable password is used. If you configure aaa authentication enable default , Dell Networking...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Related Commands line — applies an aut...

Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Intr...

Parameters encryption-type (OPTIONAL) Enter the number 7 as the encryption type. Enter 7 followed a text string as the hidden password. The text string must be a password that was already encrypted by a Dell Networking router. Use this parameter only with a password that you copied from the show run...

Related Commands show running-config — views the current configuration. privilege level (CONFIGURATION mode) — controls access to the command modes within the switch. login authentication To designate the terminal lines, apply an authentication method list. S6000 Syntax login authentication { method...

Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Intr...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Serie...

Defaults The default encryption type for the password option is 0 . The default encryption type for the secret option is 0 . Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Li...

debug radius View RADIUS transactions to assist with troubleshooting. S6000 Syntax debug radius To disable debugging of RADIUS, use the no debug radius command. Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platfo...

• For Loopback interfaces, enter the keyword loopback then a number from zero (0) to 16838. • For the Null interface, enter the keywords null 0 . • For a Port Channel interface, enter the keywords port- channel then a number. The range is from 1 to 128. • For a ten-Gigabit Ethernet interface, enter ...

Defaults Disabled. Command Modes EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. ...

Max-EAP-Req: 2 Host Mode: SINGLE_HOST Auth PAE State: Initialize Backend State: Initialize Dell# SSH Server and SCP Commands Dell Networking OS supports secure shell (SSH) protocol versions 1.5 and 2.0. SSH is a protocol for secure remote login over an insecure network. SSH sessions are encrypted an...

Defaults none Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide. The following is a list of the Dell Networking OS version history for this command. Version...

Defaults 10 per minute Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this comman...

Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. Usage Information The server-generated key is used for SSHv1 key-exchange. ip ssh password-authentication Enable password a...

ip ssh rekey Configures the time rekey-interval or volume rekey-limit threshold at which to re-generate the SSH key during an SSH session. Syntax ip ssh rekey [time rekey-interval ] [volume rekey-limit ] To reset to the default, use no ip ssh rekey [time rekey-interval ] [volume rekey-limit ] comman...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Serie...

NOTE: If you enable FIPS mode, you can only select version 2. Defaults Default listening port is 22 . Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . Th...

To disable the SSH server configuration, use the no ip ssh server vrf {management | vrf-name} command. Parameters vrf management Enter the key word vrf followed by the keyword management to configure an SSH server on a management VRF. vrf vrf-name Enter the key word vrf followed by the VRF name to c...

Parameters interface Enter the following keywords and slot/port or number information: • For a 100/1000 Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For a Gigabit Ethernet interface, enter the keyword GigabitEthernet then the slot/port information. • For Lo...

To delete a VRF for an outgoing SSH connection, use the no ip ssh vrf vrf- name command. Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to configure that VRF for an outgoing SSH session. Defaults Not configured. Command Modes CONFIGURATION Command History This guide is pl...

ssh Open an SSH connection specifying the hostname, username, encryption cipher, HMAC algorithm, port number, and version of the SSH client. S6000 Syntax NOTE: Some of the parameters in this command require licensing to access. For more information, contact your Dell Networking representative. ssh [...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.12.0 Added support for the -c and -m parameters on the S4810. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version...

ip dhcp source-address-validation Enable IP source guard. S6000 Syntax [no] ip dhcp source-address-validation Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Li...

Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.8.1.0 Introduced on the C-Series and S-Series. Usage Information When enabled, the system begins creating entries in the binding table for the specified VLANs. NOTE: Learning only happens if there is a trust...

2. Configure login authentication on the console. This ensures that all users are properly identified through authentication no matter the access point 3. Specify an authentication method (RADIUS, TACACS+, or Local). 4. Specify authorization method (RADIUS, TACACS+ or Local). 5. Verify the configura...

Defaults none Command Modes CONFIGURATION Command History Version 9.5.(0.0) Introduced on the Z9000, S6000, S4820T, S4810, MXL Related Commands userrole show role Display information on permissions assigned to a command, including user role and/or permission level. Syntax show role mode { mode } { c...

show userroles Display information on all defined user roles. Syntax show userroles Example Dell#show userroles Role Inheritance Modes netoperator Exec netadmin Exec Config Interface Line Router IP Route-map Protocol MAC secadmin Exec Config sysadmin Exec Config Interface Line Router IP Route-map Pr...

45 Service Provider Bridging Service provider bridging is composed of virtual local area network (VLAN) Stacking, Layer 2 Protocol Tunneling, and Provider Backbone Bridging as described in the Dell Networking OS Configuration Guide Service Provider Bridging chapter. This chapter includes command lin...

sflow collector Configure a collector device to which sFlow datagrams are forwarded. S6000 Syntax sflow collector { ip-address | ipv6-address } agent-addr { ip- address | ipv6-address } [ number [max-datagram-size number ]] | [max-datagram-size number ] [vrf management] To delete a configured collec...

Defaults The Global default sampling. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history ...

47 Simple Network Management Protocol (SNMP) and Syslog This chapter contains commands to configure and monitor the simple network management protocol (SNMP) v1/v2/v3 and Syslog. Both features are supported on the S6000 platform.The chapter contains the following sections: • SNMP Commands • Syslog C...

show snmp Display the status of SNMP network elements. S6000 Syntax show snmp Command Modes • EXEC• EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is ...

show snmp engineID Display the identification of the local SNMP engine and all remote engines that are configured on the router. S6000 Syntax show snmp engineID Command Modes • EXEC• EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer ...

> snmpwalk -c public 10.10.10.130 .1.3.6.1.2.1.31 | grep -i alias | more IF-MIB::ifAlias.134530304 = STRING: This is a port connected to Router2. This is a port connected to IF-MIB::ifAlias.134792448 = STRING: !------command run on Dell Networkingswitch: --------------! Dell#snmp ifmib ifalias lo...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command snmp-server enable traps Enable SNMP traps. S6000 Syntax snmp-...

snmp-server community — configures a new community SNMPv1 or SNMPv2c. snmp-server location Configure the location of the SNMP server. S6000 Syntax snmp-server location text To delete the SNMP location, use the no snmp-server location command. Parameters text Enter an alpha-numeric text string, up to...

Defaults Enabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Versio...

Version 9.0.2.0 Introduced on the S6000. Version 9.2(0.0) Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux (PMUX) mode only. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 ...

E-Series legacy command Related Commands logging console — sets the logging console parameters. default logging monitor Return to the default settings for messages logged to the terminal. S6000 Syntax default logging monitor Defaults level = 7 or debugging Command Modes CONFIGURATION Command History...

Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Intr...

logging buffered Enable logging and specify which messages are logged to an internal buffer. By default, all messages are logged to the internal buffer. S6000 Syntax logging buffered [ level ] [ size ] To return to the default values, use the default logging buffered command. To disable logging stor...

logging facility Configure the Syslog facility used for error messages sent to Syslog servers. S6000 Syntax logging facility [ facility-type ] To return to the default values, use the no logging facility command. Parameters facility-type (OPTIONAL) Enter one of the following parameters: • auth (auth...

The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Versi...

Usage Information When the number of messages reach the limit you set with the logging history size command, older messages are deleted as newer ones are added to the table. Related Commands show logging — displays information logged to the history buffer. logging monitor Specify which messages are ...

logging source-interface Specify that the IP address of an interface is the source IP address of Syslog packets sent to the Syslog server. S6000 Syntax logging source-interface interface To disable this command and return to the default setting, use the no logging source-interface command. Parameter...

Version 8.3.7.0 Introduced on the S4810. Version 8.5.1.0 Added support for 4-port 40G line cards on ExaScale. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Syslog messages contain the IP address of the interface used...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Information Whe...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series, S55. Version 7.5.1.0 Introduced on the C-Series. E-Series legacy command Usage Informatio...

Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 192.200.12.2 Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 1.1.10.2 Up Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Session closed by neighbor 1.1.10.2 (Hold time expired) Oct 8 09:25:38: %RPM1:RP1 %BGP-5-ADJCHANGE: Neighbor 192.200.14...

Version 7.6.1.0 Introduced on the S-Series. Usage Information This command displays internal software driver information, which may be useful during troubleshooting switch initialization errors, such as a downed Port-Pipe. terminal monitor Configure the Dell Networking OS to display messages on the ...

show storm-control broadcast Display the storm control broadcast configuration. S6000 Syntax show storm-control broadcast [ interface ] Parameters interface (OPTIONAL) Enter one of the following interfaces to display the interface-specific storm control configuration: • For a 1-Gigabit Ethernet inte...

show storm-control multicast Display the storm control multicast configuration. S6000 Syntax show storm-control multicast [ interface ] Parameters interface (OPTIONAL) Enter one of the following interfaces to display the interface specific storm control configuration: • For Fast Ethernet, enter the ...

51 System Time and Date The commands in this chapter configure time values on the system, either using the Dell Networking operating software, or the hardware, or using the network time protocol (NTP). With NTP, the switch can act only as a client to an NTP clock host.For more information, refer to ...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Serie...

clock summer-time recurring Set the software clock to convert to daylight saving time on a specific day each year. S6000 Syntax clock summer-time time-zone recurring [ start-week start-day start-month start-time end-week end-day end-month end-time [ offset ]] To delete a daylight saving time zone co...

debug ntp Display network time protocol (NTP) transactions and protocol messages for troubleshooting. S6000 Syntax debug ntp {adjust | all | authentication | events | loopfilter | packets | select | sync} To disable debugging of NTP transactions, use the no debug ntp {adjust | all | authentication |...

Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.1.1.0 Introduced on the E-Series. ntp authenticate Enable authentication of NTP traffic between the switch and the NTP time serving hosts. S6000 Syntax ntp authenticate To disable NTP authentication, use the no ntp authentication command. Def...

ntp broadcast client Set up the interface to receive NTP broadcasts from an NTP server. S6000 Syntax ntp broadcast client To disable broadcast, use the no ntp broadcast client command. Defaults Disabled. Command Modes INTERFACE Command History This guide is platform-specific. For command information...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.4.1.0 Added support for IPv6 multicast addresses. Version 8.3.7.0 Introduced on the S4810. pre-Version 6.1.1.0 Introduced on the E-Series. show calendar Display the...

Related Commands show clock — displays the time and date from the switch software clock. show clock Display the current clock settings. S6000 Syntax show clock [detail] Parameters detail (OPTIONAL) Enter the keyword detail to view the source information of the clock. Command Modes • EXEC• EXEC Privi...

Configuration of IPv6 commands over decapsulate-any tunnel causes an error. tunnel source Set a source address for the tunnel. S6000 Syntax tunnel source { ip-address | ipv6–address | interface-type- number | anylocal} To delete the current tunnel source address, use the no tunnel source command. Pa...

to any IPv4 or IPv6 (depending on the tunnel mode) address configured on the switch that is operationally Up . tunnel keepalive Configure the tunnel keepalive target, interval and attempts. S6000 Syntax tunnel keepalive { ip-address | ipv6-address }[interval { seconds }] [attempts { count | unlimite...

tunnel dscp Configure the method to set the DSCP in the outer tunnel header. S6000 Syntax tunnel dscp {mapped | <value> } To use the default tunnel mapping behavior, use the no tunnel dscp value command. Parameters mapped Enter the keyword mapped to map the original packet DSCP (IPv4)/Traffic ...

tunnel destination Set a destination endpoint for the tunnel. S6000 Syntax tunnel destination { ip-address | ipv6–address } To delete a tunnel destination address, use the no tunnel destination { ip- address | ipv6–address } command. Parameters ip-address Enter the destination IPv4 address for the t...

dei enable Make packets eligible for dropping based on their DEI value. S6000 Syntax dei enable Defaults Packets are colored green; no packets are dropped. Command Modes CONFIGURATION Command History This guide is platform-specific. For command information about other platforms, refer to the relevan...

Command Modes INTERFACE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduc...

Version 9.0.2.0 Introduced on the S6000. Version 8.3.19.0 Instroduces on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 8.3.1.0 Introduced on the C-Series and S-Series. Usage Information You must first enable DEI for this configuration to take ...

vlan-stack compatible Enable the stackable VLAN feature on a VLAN. S6000 Syntax vlan-stack compatible To disable the Stackable VLAN feature on a VLAN, use the no vlan-stack compatible command. Defaults Not configured. Command Modes CONF-IF-VLAN Command History This guide is platform-specific. For co...

ip vrf forwarding Enables you to attach an interface to a VRF. S6000 Syntax ip vrf forwarding { vrf-name | management} To delete an interface associated with a configured VRF, use the no ip vrf forwarding { vrf-name | management} command. Parameters vrf-name Enter name of the VRF that you want to as...

Dell(conf-if-te-7/45)#int te 7/46 Dell(conf-if-te-7/46)#no shut Dell(conf-if-te-7/46)#ip vrf forwarding red Dell(conf-if-te-7/46)#ip add 100.1.1.1/24 Dell(conf-if-te-7/46)# Dell(conf-if-te-7/46)# Dell(conf-if-te-7/46)# Dell(conf-if-te-7/46)#show config ! interface TenGigabitEthernet 7/46 ip vrf forw...

show ip vrf Displays information corresponding to the VRFs that are configured in the system. Syntax show ip [vrf vrf-name ] Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF to display information corresponding to that VRF.. Command Modes EXEC EXEC Privilege Command History...

show run vrf Displays configuration information corresponding to all the VRFs in the system. Syntax show run vrf vrf-name Parameters vrf vrf-name Enter the keyword vrf and then the name of the VRF.. Command Modes • EXEC• EXEC Privilege Command History This guide is platform-specific. For command inf...

ipv6 Enter the keyword ipv6 then an IPv6 address in the X:X:X:X::X format. interval seconds Enter the keyword interval to specify the time interval to send hello messages. The range is from 1 to 5 seconds. The default is 1 second. Defaults 1 second Command Modes VLT DOMAIN Command History This guide...

Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9.2(0.0) Introd...

Default 32768 Command Modes VLT DOMAIN Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of the Dell Networking OS version history for this command. Version 9...

HeartBeat Timeout: 3 UDP Port: 34998 HeartBeat Messages Sent: 1026 HeartBeat Messages Received: 1025 show vlt counters Displays the counter information. S6000 Syntax show vlt counters [arp| igmp-snoop | interface | mac | ndp] Parameters arp Enter the keyword arp to display the ARP counter informatio...

------------------------- L2 Total MAC-Address Count : IGMP MRouter Vlans count : IGMP Mcast Groups count : ARP entries count : Example (igmp-snoop) Dell# show vlt counter igmp-snoop Total IGMP VLT counters ---------------------- IGMP MRouter Vlans count : 1 IGMP Mcast Groups count : 5 Example (igmp...

The following is a list of the Dell Networking OS version history for this command. Version 9.0.2.0 Introduced on the S6000. Version 9.0.0.0 Introduced on the Z9000. Version 8.3.19.0 Introduced on the S4820T. Version 8.3.8.0 Introduced on the S4810. Example Dell# Dell(conf-if-vl-100)#show vlt detail...

show vlt mismatch Display mismatches in VLT parameters. S6000 Syntax show vlt mismatch Command Modes EXEC Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . The following is a list of...

show vlt role Displays the VLT peer status, role of the local VLT switch, VLT system MAC address and system priority, and the MAC address and priority of the local VLT device. S6000 Syntax show vlt role Default Not configured. Command Modes EXEC Command History This guide is platform-specific. For c...

show vlt statistics Displays statistics on VLT operations. S6000 Syntax show vlt statistics [arp | domain | igmp-snoop | mac | multicast | ndp] Parameters domain Display the VLT statistics for the domain. multicast Display the VLT statistics for multicast. mac Display the VLT statistics for the MAC ...

show vlt statistics igmp-snoop Displays the informational packets and IGMP control PDUs that are exchanged between VLT peer nodes. S6000 Syntax show vlt statistics igmp-snoop Default Not configured. Command Modes EXEC Command History This guide is platform-specific. For command information about oth...

57 Virtual Extensible LAN (VXLAN) Virtual Extensible LAN (VXLAN) is supported on the S6000 platform. feature vxlan Enable VXLAN configuration globally on the platform. S6000 Syntax feature vxlan To disable the VXLAN, use the no feature vxlan command. Defaults Disabled Command Modes CONFIGURATION Com...

Defaults Disabled Command Modes VXLAN INSTANCE Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . Version 9.4.(0.0) Introduced on the S6000. Usage Information Related Commands vxlan-i...

Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . Version 9.4.(0.0) Introduced on the S6000. Example Dell# show vxlan vxlan-instance <1> unicast-mac-local Total Local Mac Count...

Command Modes • EXEC• EXEC Privilege Command History This guide is platform-specific. For command information about other platforms, refer to the relevant Dell Networking OS Command Line Reference Guide . Version 9.4.(0.0) Introduced on the S6000. Example Dell#show vxlan vxlan-instance 1 statistics ...

Version 9.4.(0.0) Introduced on the S6000. Example Dell#show vxlan vxlan-instance 1 physical-locator Instance : 1 Tunnel : count 1 36.1.1.1 : vxlan_over_ipv4 (up) Related Commands vxlan-instance - Enable VXLAN Instance configuration on the platform. show vxlan vxlan-instance logical network Displays...

VFI : 28674 Unknown Multicast MAC Tunnels: 192.168.122.133 : vxlan_over_ipv4 (up) Port Vlan Bindings: Te 0/80: VLAN: 0 (0x80000001), Fo 0/124: VLAN: 0 (0x80000004), Related Commands vxlan-instance - Enable VXLAN Instance configuration on the platform. clear vxlan vxlan-instance statistics Syntax cle...

58 Virtual Router Redundancy Protocol (VRRP) Virtual router redundancy protocol (VRRP) is supported by the Dell Networking operating system on the S6000 platform. IPv4 VRRP Commands The following are IPv4 VRRP commands. advertise-interval Set the time interval between VRRP advertisements. S6000 Synt...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Usage Information The given password i...

Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Example Dell#clear counters vrrp vrf jay Clear "show vrrp" counters of all vrrp groups on all interfaces in VRF jay [confirm] yes debug vrrp Allows you to enable debugging of VRRP. S6000 Syntax debug ...

Version 8.3.19.0 Introduced on the S4820T. Version 8.3.11.1 Introduced on the Z9000. Version 8.3.7.0 Introduced on the S4810. Version 7.6.1.0 Introduced on the S-Series. Version 7.5.1.0 Introduced on the C-Series. pre-Version 6.2.1.1 Introduced on the E-Series. Example Dell(conf-if-vrid-4)#show con ...

Usage Information This command applies to a single interface. When used with the vrrp delay reload CLI, the later timer rules the VRRP enabling. For example, if vrrp delay reload is 600 and the vrrp delay minimum is 300: • When the system reloads, VRRP waits 600 seconds (10 minutes) to bring up VRRP...