Dell E177FP- Manuals

Monitor Specifications General Model number E177FP Flat Panel Screen type Active matrix - TFT LCD Screen dimensions 17 inches (17-inch diagonal viewable image size) Preset display area: Horizontal 337.9 mm (13.3 inches) Vertical 270.3 mm (10.6 inches) Pixel pitch 0.264 mm x 0.264 mm Viewing angle Vi...

Power Management Modes If you have VESA's DPMS compliance display card or software installed in your PC, the monitor can automatically reduce its power consumption when not in use. This is referred to as 'Power Save Mode'. If input from keyboard, mouse or other input devices is detected by the compu...

Pin Assignments VGA Connector The following table shows pin assignments in the VGA connector: Plug and Play Capability You can install the monitor in any Plug and Play-compatible system. The monitor automatically provides the computer system with its Extended Display Identification Data (EDID) using...

Back to Contents Page Appendix Dell™ E177FP Flat Panel Monitor User's Guide FCC Notice (U.S. Only) CAUTION: Safety Instruction Contacting Dell Your Monitor Set-up Guide Product Information Guide FCC Notice (U.S. Only) FCC Class B This equipment generates, uses, and can radiate radio frequency energy...

l Place your monitor in a location with low humidity and minimum dust. Avoid places similar to a damp basement or dusty hallway. l Do not expose the monitor to rain or use it near water (in kitchens, next to swimming pools, etc.). If the monitor accidentally gets wet, unplug it and contact an author...

    Your Monitor Set-up Guide To view PDF files (files with an extension of .pdf ), click the document title. To save PDF files (files with an extension of .pdf ) to your hard drive, right-click the document title, click Save Target As in Microsoft ®  Internet Explorer or Save Link As in Netscape Na...

Back to Contents Page Using the OSD Dell™ E177FP Flat Panel Monitor User's Guide Connecting Your Monitor Using the Front Panel Buttons Using the OSD Using the Dell™ Soundbar (Optional) Connecting Your Monitor 1. Turn off your computer and unplug its power cable. 2. Connect the blue (analog D-sub) di...

On Screen Menu/Display (OSD) Direct-Access Functions Using the OSD Accessing the Menu System 1. With the menu off, press the 'MENU' button to open the OSD system and display the main features menu. Brightness/Contrast Hot Key B C - and + buttons Use these buttons to adjust (decrease/increase ranges)...

Automatic Save With the OSD open, if you make an adjustment and then either proceed to another menu, or exit the OSD, the monitor automatically saves any adjustments you have made. If you make an adjustment and then wait for the OSD to disappear the adjustment will also be saved. Reset Functions Fac...

OSD Warning Messages A warning message may appear on the screen indicating that the monitor is out of sync. This means that the monitor cannot synchronize with the signal that it is receiving from the computer. Either the signal is too high or too low for the monitor to use. See  Specifications  for...

Soundbar Attachment to the Monitor Back to Contents Page 2. Power indicator 3. Power/Volume control 1. Working from the rear of the monitor, attach the Soundbar aligning the two slots with the two tabs along the bottom rear of the monitor. 2. Slide the Soundbar to the left until it snaps into place....

Back to Contents Page   Product Specific Problems Dell™ E177FP Flat Panel Monitor User's Guide     Monitor Specific Troubleshooting   Common Problems   Product Specific Problems   Monitor Specific Troubleshooting   Self-Test Feature Check (STFC) Your monitor provides a self-test feature that allows ...

Back to Contents Page   Using Your Monitor Stand DellT E177FP Flat Panel Monitor User's Guide Attaching the Stand Organizing Your Cables Using the Tilt Removing the Stand Attaching the Stand 1. Place the stand on a flat surface. 2. Fit the groove on the back of the monitor onto the two teeth of the ...

Tilt With the built-in pedestal, you can tilt the monitor for the most comfortable viewing angle. Removing the Stand After placing the monitor panel on a soft cloth or cushion, press and hold the LCD removal button, and then remove the stand. Back to Contents Page NOTE: To prevent scratches on the L...