Dell D1901Nc- Manuals

Page 2 - TABLE OF CONTENTS

TABLE OF CONTENTS FOR YOUR SAFETY ----------------------------------------------------------- 1 SAFETY PRECAUTIONS ------------------------------------------------ 2 SPECIAL NOTES ON LCD MONITORS ----------------------------- 3 BEFORE YOU OPERATE THE MONITOR ------------------------------- 3 FEATURE...

Page 3 - FCC Class B Radio Frequency Interference Statement; which the receiver is connected.

1 Before operating the monitor, please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digit...

Page 4 - PRECAUTIONS; The monitor should be operated only from the type of power source

2 PRECAUTIONS • Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. • Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Us...

Page 5 - BEFORE YOU OPERATE THE MONITOR; FEATURES; Recommended Resolutions:; PACKAGE LIST; The product package should include the following items:

3 SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. NOTES • Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears. • ...

Page 6 - INSTALLATION INSTRUCTIONS; Install; POWER CORD

INSTALLATION INSTRUCTIONS Install Remove Figure 1 Installing and Removing the Base POWER CORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V A...

Page 7 - Connecting the Signal Cable:; Plug the Signal Cable one end to LCD; Connecting the Power Cord:; Plug one end of the AC power cord to the

CONTROLS AND CONNECTORS SIGNAL CABLE Connecting the Signal Cable: Plug the Signal Cable one end to LCD monitor’s “DSUB-Input” socket , the other end to the computer’s VGA port and tighten the two screws on the cable connector. Connecting the Power Cord: Plug one end of the AC power cord to the LCD m...

Page 9 - OPERATING INSTRUCTIONS; GENERAL INSTRUCTIONS; The power cord should be connected.

7 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. • The power cord should be con...

Page 10 - FRONT PANEL CONTROL; Power Button; Power saving; NOTES; input source showed in the message bar. Press Menu/Enter button to

8 FRONT PANEL CONTROL • Power Button : Press this button to switch ON/OFF of monitor’s power. • Power Indicator: Blue — Power On mode. Orange — Power saving mode. • MENU/ENTER : Active OSD menu or function adjust confirm or Exit OSD menu when in Contrast/Brightness OSD status. • ECO Hotkey(-) Activa...

Page 11 - HOW TO ADJUST A SETTING

9 • To keep the monitor looking new, clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. Never use strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage the cabinet. As a safety precaution, always ...

Page 12 - ADJUSTING THE PICTURE; Phase

10 ADJUSTING THE PICTURE The descriptions for function control LEDS Main Menu Item Main Menu Icon Sub Menu Item Sub Menu Description Brightness Backlight Adjustment Contrast Contrast from Digital-register. Standard Standard Mode Text Text Mode Internet Internet Mode Game Game Mode Movie Movie Mode E...

Page 14 - PLUG AND PLAY; Plug & Play DDC2B Feature; THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS; USING THE RIGHT POWER CORD :; female configuration.

12 PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capab...

Page 15 - Possible Solution

13 TECHNICAL SUPPORT (FAQ) Problem & Question Possible Solution Power LED is not on *Check if the Power Switch is in the ON position *Power Cord should be connected No Plug & Play *Check if the PC system is Plug & Play compatible *Check if the Video Card is Plug & Play compatible *Ch...

Page 16 - CABLE NOT CONNECTED :

14 CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If the frequency is not correct, the screen shows vertical stripes and the picture has not correct width. FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment the picture has horizon...

Page 17 - APPENDIX; SPECIFICATIONS

15 APPENDIX SPECIFICATIONS Driving system TFT Color LCD LCD Panel Size 470 mm( 18.5 ") Pixel pitch 0. 3mm ( H ) ×0. 3 mm ( V ) R,G,B Analog Interface Video Input Separate Sync. H/V TTL H-Frequency 31kHz – 83 kHz V-Frequency 56-75Hz Display Colors 16.7M Colors Dot Clock 84.75 MHz Max. Resolution ...

Page 19 - FACTORY PRESET TIMING TABLE; CONNECTOR PIN ASSIGNMENT

17 FACTORY PRESET TIMING TABLE STANDARD RESOLUTION HORIZONTAL FREQUENCY (kHz) VERTICAL FREQUENCY 640×480 @60Hz 31.469 59.940 VGA 640×480 @75Hz 37.500 75.000 Dos-mode 720×400 @70Hz 31.469 70.087 800×600 @60Hz 37.879 60.317 SVGA 800×600 @75Hz 46.875 75.000 1024×768 @60Hz 48.363 60.004 XGA 1024×768 @75...