Dell 8 - Manuals

ASM Port and Protocol Information The following ports and communication protocols used by ASM to transfer and receive data. Table 1. ASM Port and Protocol Information Ports Protocols Port Type Direction Use 22 SSH TCP Inbound / Outbound I/O Module 23 Telnet TCP Outbound I/O Module 53 DNS TCP Outboun...

2 Installation and Quick Start The following sections provide installation and quick start information, including step-by-step instructions for deploying and configuring ASM in VMware vSphere or Microsoft virtualization environment. Only one instance of ASM should be installed within a network envir...

Prerequisites for Rack Server, S5000, and Compellent The following table describes the prerequisites for the FCoE solution offered using Rack Server, S5000, and Compellent. For more information, see http://en.community.dell.com/techcenter/extras/m/white_papers/20387203 Resource Prerequisites S5000 •...

Resource Prerequisites • Create a FCoE VLAN interface vlan <VLAN ID> [Create VLAN for FCoE] exit • Create FCoE Map fcoe-map default_full_fabric fabric-id <FCoE VLAN ID> vlan <FCoE VLAN Id> fc-map <FC MAP> exit • Apply FCoE MAP to interface interface fibrechannel 0/0 fabric de...

Resource Prerequisites Example interface vfc101 bind mac-address 5C:F9:DD:16:EF:07 no shutdown interface vfc102 bind mac-address 5C:F9:DD:16:EF:21 no shutdown • Move back into the VSAN database and create entries for the new VFC just created and create entries for the FC port(s) that will be used. v...

Resource Prerequisites • Instantiate but do not configure the upstream port-channel (LAG) to the core /aggregation switch. • Instantiate but do not configure the downstream port-channel (LAG) to the IOA4. • Create the VFC interface to bind to the servers CNA FIP MAC address. This can be located in t...

Resource Prerequisites Dell Compellent Create fault domain as per Dell Compellent best practices. System Center Virtual Machine Manager (SCVMM) Prerequisites ASM manages resource on Microsoft System Center Virtual Machine Manager through Windows Remote Management (WinRM). Windows RM must be enabled ...

Click Next to continue. 8. If there is more than one datastore available on the host, the Datastore page displays. Select the location to store virtual machine (VM) files, and then click Next to continue. 9. On the Disk Format page, choose one of the following options: • To allocate storage space to...

4. Click Next . h. On the Select Destination page, select the destination host group that contains the Hyper-V server where you want to deploy ASM VM. Click Next . i. On the Select Host page, select the host on which you want to deploy ASM, and then click Next . j. On the Configuration Settings page...

3 Configuring ASM Virtual Appliance You must configure the following settings in the virtual appliance console before you start using ASM: • Change Dell administrator password. For detailed information, see Changing Delladmin Password • Configure static IP Address in the virtual appliance. For detai...

4 Customizing Virtual Machine Templates for VMware and Hyper-V ASM supports cloning virtual machines (VM) or virtual machine templates in VMware, and cloning virtual machine templates in Hyper-V. For ASM virtual machine or virtual machine template cloning, the virtual machine or virtual machine temp...

NOTE: Additional lines may be present in the puppet.conf file for your system. It is not necessary to delete any information from this file. You just need to ensure the previously noted section is present in the file. Customizing Linux Template Perform the following task to customize Linux template:...

b. Run the following command, and ensure that you see the above line, to verify the crontab is updated as expected or not, crontab -l 6. After completing customization, turn off the virtual machine. To create a virtual machine template, follow the appropriate steps for virtualization environment. NO...

5 Configuring ASM Virtual Appliance for NetApp Storage Support For ASM to support NetApp, perform the following tasks: • Add NetApp Ruby SDK libraries to the appliance. For more information about adding SDK libraries, see Adding NetApp Ruby SDK • Enable HTTP/HTTPs for the NFS share. For more informa...

sudo patch /etc/pupetlabs/puppet/modules/netapp/lib/puppet/util/network_device/netapp/NaServer.rb < /tmp/NaServer.patch 8. Update the permissions on the NetApp module. To update the permissions, run the following command: sudo chmod 755 /etc/puppetlabs/puppet/modules/netapp/lib/puppet/util/networ...

6 Completing Initial Configuration Log in to ASM using the appliance IP address, After logging into ASM, you need to complete the basic configuration setup in the Initial Setup wizard. For more information about completing the initial setup, see the Active System Manger Version 8.0 User’s Guide . 37

A Deploying WinPE on the Virtual Appliance You need to perform the following configuration tasks before using ASM to deploy Windows OS. NOTE: You should use Microsoft ADK 8.1 or ADK 8.0 installed in the default location.. 1. Create a Windows .iso that has been customized for use with ASM using ADK a...

NOTE: • If any additional drivers are required, add the drivers under the “Drivers” folder in the build directory you created on your ADK machine. The drivers are installed into the Windows image, if applicable. The drivers that do not apply to the OS being processed are ignored. • If you want deplo...

B Configuring DHCP or PXE on External Servers The PXE service requires a DHCP server configured to provide boot server (TFTP PXE server) information and specific start-up file information. ASM PXE implementation uses the iPXE specification so that the configuration details include instructions to al...

Create the DHCP Policy 1. Open the Windows 2012 DHCP Server DHCP Manager. 2. In the console tree, expand the scope that will service your ASM PXE network. Right-click Policies and select New Policy . The DHCP Policy Configuration Wizard is displayed. 3. Next to Policy Name , type iPXE and enter the ...

Configuring DHCP for Linux You can manage the configuration of the Linux DHCPD service by editing the dhcpd.conf configuration file. The dhcpd.conf is located at /etc/dhcp directory of most Linux distributions. If the DHCP is not installed on your Linux server, install the Network Infrastructure Ser...