Dell 469-2116 - Manuals
Dell 469-2116 – Manual in PDF format online.
Manuals:
Manual Dell 469-2116
Summary
Contents Notes, Cautions, and Warnings..................................................................2 1 Working on Your Computer......................................................................9 Before Working Inside Your Computer ...............................................................
Working on Your Computer 1 Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help to ensure your personal safety. Unless otherwise noted, each procedure included in this document assumes that the following conditions ex...
NOTE: The color of your computer and certain components may appear differentlythan shown in this document. To avoid damaging your computer, perform the following steps before you begin working inside the computer. 1. Ensure that your work surface is flat and clean to prevent the computer cover from ...
ExpressCard 3 Removing the ExpressCard 1. Follow the procedures in Before Working On Your Computer . 2. Press in on the ExpressCard to release it from the computer. 3. Slide the ExpressCard out of the computer. Installing the ExpressCard 1. Slide the ExpressCard into its slot until it clicks into pl...
Modem Connector Plug 4 Removing The Modem Connector Plug 1. Follow the procedures in Before Working On Your Computer . 2. Insert a paper clip into the hole to pop out the modem connector plug. Installing The Modem Connector Plug 1. Insert and push in the modem connector plug into the modem port.2. F...
Battery 5 Removing The Battery 1. Follow the procedures in Before Working On Your Computer . 2. Slide the release latches to unlock the battery. 3. Rotate the outer edge of the battery upward and remove it from the computer. Installing The Battery 1. Slide the battery into its slot until it clicks i...
Subscriber Identity Module (SIM)Card 6 Removing The Subscriber Identity Module (SIM) Card 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Press in on the SIM card to release it from the computer. 4. Grasp the SIM card and pull out to release from the computer...
Hard Drive 7 Removing The Hard Drive 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the screws that secure the hard drive to the computer. 4. Slide the hard drive out of the computer. 5. Remove the screw that secures the hard-drive caddy to the hard d...
Installing The Hard Drive 1. Attach the hard-drive caddy to the hard drive.2. Tighten the screws to secure the hard-drive caddy to the hard drive.3. Slide the hard drive into the computer.4. Replace and tighten the screws to secure the hard drive to the computer.5. Install the battery . 6. Follow th...
Optical Drive 8 Removing The Optical Drive 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Press and release the optical drive latch 4. Pull the optical drive out of the computer. 5. Pull the optical drive door from one side to release it. 25
10. Remove the drive latch bracket from the optical drive. Installing The Optical Drive 1. Replace the drive latch bracket on the optical drive.2. Replace and tighten the screws to secure the drive latch bracket to the optical drive. 3. Replace the drive latch on the optical drive.4. Replace the scr...
Base Cover 9 Removing The Base Cover 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the screws that secure the base cover to the computer. 4. Lift from the back of the computer and slide towards the front of the computer. 5. Remove the base cover from...
Installing The Base Cover 1. Place the base cover to align the screw holes correctly with the computer.2. Tighten the screws to secure the base cover to the computer.3. Install the battery . 4. Follow the procedures in After Working Inside Your Computer . 30
Memory 10 Removing The Memory 1. Follow the procedures in Before Working On Your Computer 2. Remove the battery . 3. Remove the secure digital (SD) Card . 4. Remove the base cover . 5. Pry the retention clips away from the memory module until it pops up. 6. Remove the memory module. 31
Installing The Memory 1. Insert the memory into the memory socket.2. Press the clips to secure the memory module to the system board.3. Install the base cover . 4. Install the secure digital (SD) Card . 5. Install the battery . 6. Follow the procedures in After Working Inside Your Computer . 32
Bluetooth Card 11 Removing Bluetooth Card 1. Follow the procedures in Before Working on Your Computer . 2. Remove the battery . 3. Remove the base cover . 4. Disconnect the Bluetooth cable from the system board. 5. Remove the screw that secures the Bluetooth card to the system board. 6. Lift and rem...
7. Disconnect the Bluetooth cable from the Bluetooth card. Installing The Bluetooth Card 1. Connect the bluetooth cable to the bluetooth card.2. Connect the other end of the bluetooth cable to the system board.3. Place the Bluetooth card in its location in the computer.4. Replace and tighten the scr...
Coin-Cell Battery 12 Removing The Coin-Cell Battery 1. Follow the procedures in Before Working on Your Computer . 2. Remove the battery . 3. Remove the base cover . 4. Disconnect the coin-cell battery cable from the system board. 5. Release and remove the coin-cell battery from the computer. Install...
Modem Card 13 Removing The Modem Card 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the base cover . 4. Disconnect the connector that secures the modem card to the system board. 5. Remove the screw securing the modem to the system. 6. Lift and remove...
Installing The Modem Card 1. Fasten the connector attaching the modem card to the system board.2. Insert the modem into its compartment and press on the module to connect it to the system board. 3. Connect the modem cable to the system board.4. Tighten the screw to secure the modem card to the compu...
Modem Connector 14 Removing The Modem Connector 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the secure digital (SD) Card . 4. Remove the base cover . 5. Remove the modem card . 6. Disconnect the antenna cables. 7. Unthread the antenna cables from t...
Installing The Modem Connector 1. Align the modem connector to its original position.2. Align the modem bracket to its original position.3. Tighten the screw to secure the modem bracket.4. Route and connect the modem cable.5. Route and connect the antenna cables.6. Install the modem card . 7. Instal...
Wireless Local Area Network(WLAN) Card 15 Removing The Wireless Local Area Network (WLAN) Card 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the base cover . 4. Disconnect the antenna cables from the WLAN card. 5. Remove the screw that secures the WL...
Installing The Wireless Local Area Network (WLAN) Card 1. Insert the WLAN card into its connector at a 45–degree angle into its slot.2. Connect the antenna cables to their respective connectors marked on the WLAN card. 3. Replace and tighten the screw to secure the WLAN card to the computer.4. Insta...
Wireless Wide Area Network(WWAN) Card 16 Removing The Wireless Wide Area Network (WWAN) Card 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the base cover . 4. Disconnect the antenna cables from the WWAN card. 5. Remove the screw that secures the WWAN...
Installing The Wireless Wide Area Network (WWAN) Card 1. Insert the WWAN card into its connector at a 45–degree angle into its slot.2. Connect the antenna cables to their respective connectors marked on the WWAN card. 3. Replace and tighten the screw to secure the WWAN card to the computer.4. Instal...
Power Connector 17 Removing The Power Connector 1. Follow the procedures in Before Working on Your Computer . 2. Remove the battery . 3. Remove the base cover . 4. Disconnect and remove the power connector cable from the route. 5. Remove the screw that secures the power connector bracket to the comp...
7. Remove the power connector trim. Installing The Power Connector 1. Align the power connector port trim in its original position.2. Tighten the screw to secure the power connector trim to the computer.3. Insert the power connector in its compartment.4. Install the power connector bracket in its pl...
Heat Sink 18 Removing The Heat-Sink 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the base cover . 4. Disconnect the heat-sink cable from the system board. 5. Remove the screws that secure the heat-sink assembly to the system board. 6. Lift up to rai...
Installing The Heat-Sink 1. Slide the heat-sink into its original position in the system board.2. Tighten the screws to secure the heat-sink assembly to the system board.3. Connect the heat-sink cable to the system board.4. Install the base cover . 5. Install the battery . 6. Follow the procedures i...
Processor 19 Removing The Processor 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the base cover . 4. Remove the heat-sink . 5. Rotate the processor cam lock in a counter-clockwise direction. 6. Lift up and remove the processor from the system board....
Installing The Processor 1. Align the notches on the processor and the socket.2. Slide the processor into the socket.3. Rotate the processor cam lock in a clockwise direction.4. Install the heat-sink . 5. Install the base cover . 6. Install the battery . 7. Follow the procedures in After Working Ins...
Keyboard Trim 20 Removing The Keyboard Trim 1. Follow the procedures in Before Working On Your Computer . 2. Using a plastic scribe, pry under the keyboard trim to release it from the computer. 3. Lift the keyboard trim to release the tabs. 4. Pry up the keyboard trim from the bottom center. 5. Lift...
Installing The Keyboard Trim 1. Align the keyboard trim to its compartment.2. Press along the sides of the keyboard trim until it snaps in place.3. Follow the procedures in After Working Inside Your Computer . 54
Keyboard 21 Removing The Keyboard 1. Follow the procedures in Before Working On Your Computer . 2. Remove the keyboard trim . 3. Remove the battery . 4. Remove the base cover . 5. Remove the screws that secure the keyboard to the palm rest assembly 6. Flip the keyboard over. 7. Lift the clip to rele...
Installing The Keyboard 1. Connect the keyboard cable and secure it to the keyboard using the tape.2. Slide the keyboard into its compartment until all the metal tabs fit into their positions. 3. Press down on the keyboard to the left and right side ensuring that all the snaps are fully engaged with...
Palm Rest 22 Removing The Palm Rest Assembly 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the base cover . 4. Remove the display assembly . 5. Remove the optical drive . 6. Remove the hard drive . 7. Remove the bluetooth . 8. Remove the keyboard tri...
• Radio Frequency Identification (RFID) sensor• touch pad• media board 13. Lift the palm rest at a 45-degree angle and remove it. Installing The Palm Rest Assembly 1. Align the palm rest assembly to its original position in the computer and snap it into place. 2. Connect the following cables to the ...
Smart Card Reader 23 Removing the Smart Card Reader 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the base cover . 4. Remove the display assembly . 5. Remove the optical drive . 6. Remove the hard drive . 7. Remove the bluetooth module . 8. Remove th...
Installing The Smart Card Reader 1. Insert the smart card reader in the computer in its original position.2. Tighten the screws of the smart card reader.3. Connect the smart card reader cable to the system board.4. Install the palm rest assembly . 5. Install the keyboard . 6. Install the keyboard tr...
ExpressCard Cage 24 Removing The ExpressCard Cage 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the ExpressCard . 4. Remove the optical drive . 5. Remove the base cover . 6. Remove the hard drive . 7. Remove the bluetooth . 8. Remove the keyboard tri...
Installing The ExpressCard Cage 1. Insert the ExpressCard cage into its original position.2. Replace and tighten the screws to secure the ExpressCard cage to the computer. 3. Install the display assembly . 4. Install the palm rest assembly . 5. Install the keyboard . 6. Install the keyboard trim . 7...
Wireless Switch Board 25 Removing The Wireless Switch Board 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the base cover . 4. Remove the display assembly . 5. Remove the optical drive . 6. Remove the hard drive . 7. Remove the Bluetooth . 8. Remove t...
Installing The Wireless Switch Board 1. Align the wireless switch board into its original position in the computer.2. Tighten the screw on the board.3. Route and connect the wireless switch cable in the system board.4. Install the palm rest assembly . 5. Install the keyboard . 6. Install the keyboar...
System Board 26 Removing The System Board 1. Follow the procedures in Before Working On Your Computer . 2. Remove the secure digital (SD) Card . 3. Remove the ExpressCard . 4. Remove the battery . 5. Remove the base cover . 6. Remove the display assembly . 7. Remove the optical drive . 8. Remove the...
27. Lift and slide the system board out of the computer. Installing The System Board 1. Align the system board into its original position on the computer.2. Replace and tighten the screws to secure the system board to the computer. 3. Route and connect the following cables the system board: • LVDS• ...
Speaker 27 Removing The Speakers 1. Follow the procedures in Before Working On Your Computer . 2. Remove the secure digital (SD) Card . 3. Remove the ExpressCard . 4. Remove the battery . 5. Remove the base cover . 6. Remove the display assembly . 7. Remove the optical drive . 8. Remove the hard dri...
Installing The Speakers 1. Align the speakers in the original position and connect the speaker cables.2. Tighten the screws to secure the speakers.3. Slide the hard drive support plate into its position.4. Tighten the screw to secure the hard drive support plate to the computer.5. Install the system...
Display Assembly 29 Removing The Display Assembly 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the base cover . 4. Release the antenna cables from the computer. 5. Remove the screws that secures the low-voltage differential signaling (LVDS) support ...
Installing The Display Assembly 1. Insert the low-voltage differential signaling (LVDS) cable and wireless antenna cables through the holes on the bottom base chassis. 2. Attach the display assembly hinges to the bottom base chassis.3. Replace and tighten the screws to secure the display assembly to...
Display Bezel 30 Removing The Display Bezel 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Pry the display bezel from inside the display assembly. 4. Remove the display bezel. Installing The Display Bezel 1. Place the display bezel onto the display assembly....
Display Panel 31 Removing The Display Panel 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the display bezel . 4. Remove the screws that secures the display panel to the computer. 5. Flip the display panel over the keyboard. 6. Peel the tape from the ...
7. Disconnect the LVSD cable from the display panel. 8. Remove the display panel from the computer. Installing The Display Panel 1. Align the display panel in its original position in the computer.2. Connect the low-voltage differential signaling (LVSD) cable to the display panel and attach the tape...
Camera 32 Removing The Camera 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the display bezel . 4. Loosen the screw that secures the camera module. 5. Disconnect the cable and remove the camera module. Installing The Camera 1. Replace the camera modu...
Specifications 33 Technical Specifications NOTE: Offerings may vary by region. The following specifications are only thoserequired by law to ship with your computer. For more information regarding theconfiguration of your computer, click Start → Help and Support and select the option to view informa...
System Setup 34 System Setup Overview System Setup allows you to: • change the system configuration information after you add, change, or remove any hardware in your computer. • set or change a user-selectable option such as the user password.• read the current amount of memory or set the type of ha...
Diagnostics 35 Device Status Lights Turns on when you turn on the computer and blinks when the computer is in apower management mode. Turns on when the computer reads or writes data. Turns on steadily or blinks to indicate battery charge status. Turns on when wireless networking is enabled. Battery ...
Contacting Dell 36 Contacting Dell NOTE: If you do not have an active Internet connection, you can find contactinformation on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options. Availability varies by count...
Dell Manuals
-
Dell 04YJJ6A00
User Manual
-
Dell 04YJJ6A00
Manual
-
Dell 10 Pro
User Manual
-
Dell 10
Manual
-
Dell 1000
User Manual
-
Dell 1000
Manual
-
Dell 1014
User Manual
-
Dell 1000W
User Manual
-
Dell 1000W
Manual
-
Dell 0JH552A01
User Manual
-
Dell 10g
User Manual
-
Dell 1100
User Manual
-
Dell 1100
Manual
-
Dell 11
User Manual
-
Dell 11
Manual
-
Dell 11 Pro
User Manual
-
Dell 110T
User Manual
-
Dell 110T DLT1 Drive
User Manual
-
Dell 1100 Laser Mono Printer
User Manual
-
Dell 1100MP
User Manual