Dell 4620S- Manuals

Page 2 - Cable Routing Procedures for DellTM PowerEdgeTM R510 Systems; Page ii

Cable Routing Procedures for Dell™ PowerEdge™ R510 Systems Page ii THIS WHITE PAPER IS FOR INFORMATIONAL PURPOSES ONLY, AND MAY CONTAIN TYPOGRAPHICAL ERRORS AND TECHNICAL INACCURACIES. THE CONTENT IS PROVIDED AS IS, WITHOUT EXPRESS OR IMPLIED WARRANTIES OF ANY KIND. © 2009 Dell Inc. All rights reser...

Page 3 - Page 1; Contents; Table of Figures

Cable Routing Procedures for Dell™ PowerEdge™ R510 Systems Page 1 Contents Introduction ............................................................................................................................................................... 2 Section 1: Cabling a Dell™ PowerEdge™ R510 With a ...

Page 4 - Page 2; Introduction; Best Practices Guide for Rack Enclosure

Cable Routing Procedures for Dell™ PowerEdge™ R510 Systems Page 2 Introduction This white paper covers recommended cable routing procedures for Dell™ PowerEdge™ R510 systems in the following racks: • PowerEdge™ 4210 • PowerEdge™ 2410 • PowerEdge™ 4220 • PowerEdge™ 2420 If you are using the optional ...

Page 5 - Page 3

Cable Routing Procedures for Dell™ PowerEdge™ R510 Systems Page 3 1.2 Installing the Inner CMA Attachment Bracket As described in the Rack Installation Instructions, locate and attach the appropriate inner CMA attachment bracket based on which side you wish to mount the CMA. Use the bracket marked “...

Page 6 - Page 4

Cable Routing Procedures for Dell™ PowerEdge™ R510 Systems Page 4 NOTE: For guidelines on how to route cables within the rack, refer to the Dell Best Practices Guide for Rack Enclosures white paper . 1.5 Left-Side Mounting Instructions 1. Install the CMA on the rear left side of the rails by attachi...

Page 7 - Page 5

Cable Routing Procedures for Dell™ PowerEdge™ R510 Systems Page 5 Figure 5: Left-Side Mounted CMA Installation 1.6 Right-Side Mounting Instructions 1. Install the CMA on the rear right side of the rails by attaching both CMA housings to the attachment brackets on the rails. 2. Route the cables throu...

Page 8 - Page 6; Section 2: Cabling a DellTM PowerEdgeTM R510 System Without a CMA; NOTE; Routing the Cables

Cable Routing Procedures for Dell™ PowerEdge™ R510 Systems Page 6 Figure 6: Right-Side Mounted CMA Installation Section 2: Cabling a Dell™ PowerEdge™ R510 System Without a CMA NOTE : The CMA on Dell™ PowerEdge™ R510 systems is optional. W ithout the CMA installed, the system must be powered down and...

Page 9 - Page 7

Cable Routing Procedures for Dell™ PowerEdge™ R510 Systems Page 7 Figure 7: Cable Routing Without a CMA 2.2 Removing the CMA Brackets for Shallow Racks If you are installing the system into a shallow rack (less than 1 meter deep) and you will not be installing a CMA, the outer CMA brackets may be re...

Page 10 - Page 8; CMA Installation Instructions; Replacing a Power Supply with a Right-Side Mounted CMA; CMA Installation Instructions; top; Figure 9: Disconnecting the Inner CMA Attachment Bracket

Cable Routing Procedures for Dell™ PowerEdge™ R510 Systems Page 8 Section 3: Replacing a Power Supply on a PowerEdge™ R510 System With a CMA 3.1 Replacing a Power Supply with a Left-Side Mounted CMA 1. If the bottom power supply must be replaced, then remove the tray from underneath the CMA as descr...

Page 11 - Page 9

Cable Routing Procedures for Dell™ PowerEdge™ R510 Systems Page 9 Figure 10: Replacing the Power Supply Section 4: Cabling a PowerEdge™ R510 System Installed in Static Rails NOTE: The CMA is compatible with the sliding rails only, not the static rails. 1. Follow the instructions contained in the Rac...