Dell 3350- Manuals

2 Battery Removing The Battery 1. Follow the procedures in Before Working On Your Computer . 2. Slide the release latches to unlock the battery. 3. Slide the battery and remove it from the computer. 11

Installing The Battery 1. Slide the battery into its slot until it clicks into place.2. Follow the procedures in After Working Inside Your Computer . 12

3 Memory Card Removing The Memory Card 1. Follow the procedures in Before Working On Your Computer . 2. Press in on the memory card to release it from the computer. 3. Slide the memory card out of the computer. 13

Installing The Memory Card 1. Push the memory card into the compartment until it snaps into place.2. Follow the procedures in After Working Inside Your Computer . 14

4 Subscriber Identity Module (SIM) Card Removing The Phone Subscriber Identity Module (SIM) 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Press in on the SIM card to release it from the computer. 4. Grasp the SIM card and pull out to release it from the com...

Installing The Phone Subscriber Identity Module (SIM) 1. Push the SIM card into the slot until it is fully engaged.2. Install the battery . 3. Follow the procedures in After Working Inside Your Computer . 16

5 Access Panel Removing The Access Panel 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the screws that secures the access panel to the base of the computer. 4. Lift the access panel up at an angle and remove it from the computer. 17

Installing The Access Panel 1. Tighten the screws to secure the access panel to the base of the computer.2. Install the battery . 3. Follow the procedures in After Working Inside Your Computer . 18

6 Memory Removing The Memory Module 1. Follow the procedures in Before Working On Your Computer 2. Remove the battery . 3. Remove the access panel . 4. Pry the retention clips away from the memory module until it pops up. 5. Remove the memory module from its connector on the system board. 19

Installing The Memory Module 1. Insert and secure the memory module to the system board.2. Install the access panel . 3. Install the battery . 4. Follow the procedures in After Working Inside Your Computer . 20

7 Optical Drive Removing The Optical Drive 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the access panel . 4. Remove the screw that secures the optical drive to the computer. 5. Use a screwdriver to pry the optical drive out of the computer. 21

Installing The Optical Drive 1. Slide the optical drive into its compartment on the chassis.2. Tighten the screw to secure the optical drive to the computer.3. Install the access panel . 4. Install the battery . 5. Follow the procedures in After Working Inside Your Computer . 22

8 Hard Drive Removing The Hard Drive 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the access panel . 4. Open the clip that secures the hard-drive assembly to the computer. 5. Disconnect the hard-drive cable from the hard drive. 23

10. Remove the hard drive board from the hard drive. Installing The Hard Drive 1. Install the screws to secure the hard drive board to the hard drive.2. Place the hard drive in its compartment .3. Replace the screws to secure the hard drive to the system.4. Connect the hard drive cable to the system...

9 Wireless Local Area Network (WLAN) Card Removing Wireless Local Area Network (WLAN) Card 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the access panel.4. Disconnect the antenna cables from the WLAN card. 5. Use a scribe to pry the latch to release...

6. Remove the WLAN card from the computer. Installing The Wireless Local Area Network (WLAN) Card 1. Slide the WLAN card into its slot. 2. Connect the antenna cables according to the color code on the WLAN card. 3. Install the access panel . 4. Install the battery . 5. Follow the procedures in After...

10 Keyboard Removing The Keyboard 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Using a small plastic scribe, release the four latches that secures the keyboard to the computer. 4. Flip the keyboard over and lay it on the palm rest. 29

7. If your computer comes with a backlit keyboard, disconnect the keyboard backlight cable. 8. Remove the keyboard from the computer. Installing The Keyboard 1. Connect the keyboard data cable to the system board.2. Install the battery . 3. Follow the procedures in After Working Inside Your Computer...

11 Wireless Wide Area Network (WWAN) Card Removing The Wireless Wide Area Network (WWAN) Card 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the keyboard 4. Open the power button board cable securing clip. 5. Disconnect the power button board cable. 3...

8. Remove the WWAN card from the computer. Installing The Wireless Wide Area Network (WWAN) Card 1. Slide the Wireless Wide Area Network (WWAN) card into its slot.2. Connect the antenna cables according to the color code on the WWAN card. 3. Install the power button board cable . 4. Install the keyb...

12 Palm Rest Removing The Palm Rest 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the hard drive . 6. Remove the keyboard . 7. Remove the rubber from the bottom of the computer. 8. Remove the s...

Installing The Palm Rest 1. Starting from the right edge of the palm rest, press downwards on the computer to engage the tabs. 2. Work your way around the edges and ensure the tabs are fully engaged.3. Connect all cables to the system board.4. Tighten the screws to secure the palm rest.5. Tighten th...

13 Speaker Removing The Speaker 1. Follow the procedures in Before Working on Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the hard drive . 6. Remove the keyboard . 7. Remove the palm rest . 8. Disconnect the speaker cable from its connec...

10. Release the speaker cable from the routing channel. 11. Lift the speakers up and away from the computer. Installing The Speaker 1. Install the speaker cable in the routing channel.2. Install the speaker to its securing posts.3. Connect the speaker cable.4. Install the palm rest . 5. Install the ...

14 Fingerprint Reader Removing The Fingerprint Reader 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the hard drive . 6. Remove the keyboard . 7. Remove the palm rest . 8. Release the fingerprin...

Installing The Fingerprint Reader 1. Install the fingerprint reader board and the bracket.2. Tighten the screws that secure the fingerprint reader bracket.3. Affix the finger print reader cable to the palm rest.4. Install the palm rest . 5. Install the keyboard . 6. Install the hard drive 7. Install...

15 LED Board Removing The LED Board 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the hard drive . 6. Remove the keyboard . 7. Remove the palm rest . 8. Peel open the tape that secures the LED ...

Installing The LED Board 1. Secure the latches to the LED board.2. Affix the tape to secure the LED board cable.3. Install the palm rest . 4. Install the keyboard . 5. Install the hard drive 6. Install the access panel . 7. Install the memory card . 8. Install the battery . 9. Follow the procedures ...

16 Power-Button Board Removing The Power-Button Board 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the memory . 6. Remove the hard drive . 7. Remove the keyboard . 8. Remove the palm rest . 9....

Installing The Power-Button Board 1. Install the power-button board and tighten the screw.2. Install the palm rest . 3. Install the keyboard . 4. Install the hard drive 5. Install the memory . 6. Install the access panel . 7. Install the memory card . 8. Install the battery . 9. Follow the procedure...

17 Quick Launch Button Board Removing The Quick Launch Button Board 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the memory . 6. Remove the hard drive . 7. Remove the keyboard . 8. Remove the ...

11. Pry the latches to release the quick launch button board; then lift up and remove it from the computer. Installing The Quick Launch Button Board 1. Install the quick launch button board and tighten the screw.2. Affix the quick launch button board cable to the palm rest.3. Install the palm rest ....

18 Coin-Cell Battery Removing The Coin-Cell Battery 1. Follow the procedures in Before Working on Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the hard drive . 6. Remove the keyboard . 7. Remove the palm rest . 8. Pry the tabs that secure...

19 Heat Sink Removing The Heat Sink 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the memory . 6. Remove the WLAN card . 7. Remove the optical drive . 8. Remove the hard drive . 9. Remove the k...

Installing The Heat Sink 1. Install the heat sink in the slot.2. Install the system board 3. Install the display assembly . 4. Install the palm rest . 5. Install the WWAN card . 6. Install the keyboard . 7. Install the hard drive 8. Install the optical drive . 9. Install the WLAN card . 10. Install ...

20 Processor Removing The Processor 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the memory . 6. Remove the WLAN card . 7. Remove the optical drive . 8. Remove the hard drive . 9. Remove the k...

15. Lift the processor up and away from the system board. Installing The Processor 1. Insert the processor into the processor socket. Ensure the processor is properly seated. 2. Tighten the cam lock in a clockwise direction.3. Install the system board 4. Install the display assembly . 5. Install the...

21 Display Assembly Removing The Display Assembly 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the WLAN card . 6. Remove the hard drive . 7. Remove the keyboard . 8. Remove the WWAN card . 9. ...

14. Remove the screws that secure the display assembly to the computer. 15. Lift the display assembly up from the computer, then forward and remove. Installing The Display Assembly 1. Attach the display assembly to the base of the computer.2. Tighten the screws to secure the display assembly.3. Secu...

22 Display Bezel Removing The Display Bezel 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the WLAN card . 6. Remove the hard drive . 7. Remove the keyboard . 8. Remove the WWAN card . 9. Remove...

Installing The Display Bezel 1. Place the display bezel on the computer.2. Starting from the bottom edge, press downward on the display bezel to engage the tabs. 3. Work your way around the sides and top edge.4. Install the palm rest . 5. Install the WWAN card . 6. Install the keyboard . 7. Install ...

23 Camera Removing The Camera 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the WLAN card . 6. Remove the hard drive . 7. Remove the keyboard . 8. Remove the WWAN card . 9. Remove the palm rest...

14. Pry the latch; then lift up the camera. Installing The Camera 1. Install display camera and connect the camera cable.2. Stick back tape that secures the display camera..3. Install the display bezel . 4. Install the display assembly . 5. Install the palm rest . 6. Install the WWAN card . 7. Insta...

24 Display Panel Removing The Display Panel 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the WLAN card . 6. Remove the hard drive . 7. Remove the keyboard . 8. Remove the WWAN card . 9. Remove...

Installing The Display Panel 1. Install the display cable on the display panel.2. Replace the tape to secure the display cable to the display panel.3. Install the screws that secure the display panel to the display assembly.4. Install the display bezel 5. Install the display assembly 6. Install the ...

25 Display Brackets and Hinges Removing Display Brackets And Hinges 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the WLAN card . 6. Remove the hard drive . 7. Remove the keyboard . 8. Remove t...

Installing The Display Brackets And Hinges 1. Install the display brackets and display hinges. 2. Tighten the screws to secure the display brackets and hinges to the display assembly. 3. Route the cables into the right and left hinges. 4. Install the display panel 5. Install the display bezel 6. Ins...

26 Display Cable Removing The Display Cable 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the WLAN card . 6. Remove the hard drive . 7. Remove the keyboard . 8. Remove the WWAN card . 9. Remove...

Installing The Display Cable 1. Install the display cable affixing it to the display cover. 2. Install the display brackets and hinges . 3. Install the display panel . 4. Install the display camera . 5. Install the display bezel . 6. Install the display assembly . 7. Install the palm rest . 8. Insta...

27 System Board Removing The System Board 1. Follow the procedures in Before Working On Your Computer . 2. Remove the battery . 3. Remove the memory card . 4. Remove the access panel . 5. Remove the memory . 6. Remove the WLAN card . 7. Remove the optical drive . 8. Remove the hard drive . 9. Remove...

Installing The System Board 1. Align the system board to the port connectors on the rear of the chassis and place the system board in the computer. 2. Tighten the screws to secure the system board in place.3. Replace the fan cable.4. Tighten the screws to secure the heatsink to the system board.5. I...

Installing The Input/Output Board 1. Install the Input/Output board into the slot.2. Install the system board 3. Install the display assembly . 4. Install the palm rest . 5. Install the WWAN card . 6. Install the keyboard . 7. Install the hard drive 8. Install the optical drive . 9. Install the WLAN...

29 System Setup System Setup Overview System Setup allows you to: • change the system configuration information after you add, change, or remove any hardware in your computer. • set or change a user-selectable option such as the user password.• read the current amount of memory or set the type of ha...

System Setup Screens Menu — Appears on top of the System Setup window. This field provides a menu toaccess the System Setup options. Press < Left Arrow > and < Right Arrow > keys tonavigate. As a Menu option is highlighted, the Options List lists the options that definethe hardware insta...

Keystroke Action – or + Change existing item value. < Enter > Select the sub menu or execute command. < F9 > Load setup default. < F10 > Save current configuration and exitSystem Setup. System Setup Options Main System Information Displays the computer model number. System Date Re-...

30 Diagnostics Device Status Lights Turns on when you turn on the computer and blinks when the computer is in apower management mode. Turns on when the computer reads or writes data. Turns on steadily or blinks to indicate battery charge status. Turns on when wireless networking is enabled. Battery ...

31 Specifications NOTE: Offerings may vary by region. The following specifications are only thoserequired by law to ship with your computer. For more information regarding theconfiguration of your computer, click Start → Help and Support and select the option to view information about your computer....

32 Contacting Dell Contacting Dell NOTE: If you do not have an active Internet connection, you can find contactinformation on your purchase invoice, packing slip, bill, or Dell product catalog. Dell provides several online and telephone-based support and service options.Availability varies by countr...

Figure 11. USB Connector 4. Open the computer display and press the power button to turn on the computer. Figure 12. Power Button NOTE: It is recommended that you turn on and shut down your computer at least once before you install any cards or connect the computer to a docking device or other exter...

Physical Vostro 3550/3555 Height 30.40 mm to 34.80 mm (1.20 inches to 1.37 inches) Width 375.40 mm (14.78 inches) Depth 260.20 mm (10.24 inches) Weight (minimum) 2.47 kg (5.45 lb) Vostro 3750 Height 30.80 mm to 34.80 mm (1.21 inches to 1.37 inches) Width 418.40 mm (16.47 inches) Depth 286.70 mm (11....