D-Link DES-1210-28P - Manuals

1 Product Introduction D-Link Web Smart Switch User Manual 1 Product Introduction Thank you and congratulations on your purchase of D-Link Web Smart Switch Products. D-Link's next generation Web Smart Ethernet switch series blends plug-and-play simplicity with exceptional value and reliability for s...

1 Product Introduction D-Link Web Smart Switch User Manual DES-1210-28 24-Port 10/100Mpbs with 4-Port 10/100/1000Mbps Copper and 2 Combo SFP Web Smart Switch Front Panel Figure 1 – DES-1210-28 Front Panel Power LED : The Power LED lights up when the Switch is connected to a power source. Port Link/A...

1 Product Introduction D-Link Web Smart Switch User Manual Power LED : The Power LED lights up when the Switch is connected to a power source. Port Link/Act/Speed LED (1-48): The Link/Act/Speed LED flashes which indicates a network link through the corresponding port. Blinking indicates that the Swi...

1 Product Introduction D-Link Web Smart Switch User Manual sending or receiving data to the port. When a port has amber light indicates that port is running on 10M. When it has a green light it is running on 100M. PoE Mode: When selecting the PoE Mode, the port LED lights up with solid green indicat...

2 Hardware Installation D-Link Web Smart Switch User Manual 2 Hardware Installation This chapter provides unpacking and installation information for the D-Link Web-Smart Switch. Step 1: Unpacking Open the shipping carton and carefully unpack its contents. Please consult the packing list located in t...

2 Hardware Installation D-Link Web Smart Switch User Manual Then, use the screws provided with the equipment rack to mount the switch in the rack. Figure 9 – Mount the Switch in the rack or chassis Please be aware of following safety Instructions when installing: A) Elevated Operating Ambient - If i...

2 Hardware Installation D-Link Web Smart Switch User Manual Figure 10 –Plugging the switch into an outlet Power Failure As a precaution, the switch should be unplugged in case of power failure. When power is resumed, plug the switch back in. 8

3 Getting Started D-Link Web Smart Switch User Manual 3 Getting Started This chapter introduces the management interface of D-Link Web-Smart Switch. Management Options The D-Link Web Smart Switch can be managed through any port on the device by using the Web-based Management or through any PC using ...

3 Getting Started D-Link Web Smart Switch User Manual Login Web-based Management In order to login and configure the switch via an Ethernet connection, the PC must have an IP address in the same subnet as the switch. For example, if the switch has an IP address of 10.90.90.90 , the PC should have an...

3 Getting Started D-Link Web Smart Switch User Manual installing the latest SmartConsole Utility. Option 1: Follow these steps to install the SmartConsole Utility via the autorun program on the installation CD. 1. Insert the Utility CD into your CD-Rom/DVD-Rom Drive. 2. The autorun program will appe...

4 SmartConsole Utility D-Link Web Smart Switch User Manual 4 SmartConsole Utility The D-Link SmartConsole Utility allows the administrator to quickly discover all D-Link smart switches which are in the same domain of the PC, collect traps and log messages, and quick access to basic configurations of...

4 SmartConsole Utility D-Link Web Smart Switch User Manual Figure 18 – SmartConsole File Monitor Save: Records the setting of the Device List as default for the next time the SmartConsole Utility is used. Monitor Save As: Records the setting of the Device List in an appointed filename and file path....

4 SmartConsole Utility D-Link Web Smart Switch User Manual Device Password Manager Select a switch from the Device List. Click on this icon to launch the Device Password Manager window. Here you can enter a new password and confirm it. Figure 21 – SmartConsole Device Password Manager Multi Firmware ...

4 SmartConsole Utility D-Link Web Smart Switch User Manual Figure 23 – DHCP Refresh Web Access Select a switch from the Device List. Click this icon to launch your internet browser (eg. The Internet Explorer). Here you can configure the Switch through the Web-based Management utility. You may also g...

4 SmartConsole Utility D-Link Web Smart Switch User Manual Monitor: Check the Monitor box and the SmartConsole will collect the trap and log data from the device. The in the monitor means the device was discovered by SmartConsole. Click the icon to have the device keep updating the information such ...

5 Configuration D-Link Web Smart Switch User Manual 5 Configuration The features and functions of the D-Link Web Smart Switch can be configured for optimum use through the Web-based Management Utility. Smart Wizard Configuration After a successful login, the Smart Wizard will guide you through essen...

5 Configuration D-Link Web Smart Switch User Manual System Settings You can manually change the system IP Address, Subnet Mask, and Gateway address by selecting Static and clicking Apply . You can further configure and read more about the above settings in the “Setup Menu > System > System Set...

5 Configuration D-Link Web Smart Switch User Manual Web-based Management After clicking the Exit button in Smart Wizard you will see the screen below: Tool Bar Main Configuration Screen Function Tree Figure 31 – Web-based Management Above is the Web-based Management screen. The three main areas are ...

5 Configuration D-Link Web Smart Switch User Manual Tool Bar > Save Menu The Save Menu provides Save Configuration and Save Log functions. Figure 32 – Save Menu Save Configuration Select to save the entire configuration changes you have made to the device to switch’s non-volatile RAM. Figure 33 –...

5 Configuration D-Link Web Smart Switch User Manual Figure 40 – Tool Menu > Firmware Backup and Upload HTTP: Backup or upgrade the firmware to or from your local drive of PC. Click Backup to save the firmware to your disk. Click Browse to browse your inventories for a saved firmware file. Click U...

5 Configuration D-Link Web Smart Switch User Manual Function Tree All configuration options on the switch are accessed through the Setup menu on the left side of the screen. Click on the setup item that you want to configure. The following sections provide more detailed description of each feature a...

5 Configuration D-Link Web Smart Switch User Manual AuthPriv – Both authorization and encryption are required for packets sent between the Switch and SNMP manger. Notify View Name: Specify a SNMP group name for users that can receive SNMP trap messages generated by the Switch's SNMP agent. Figure 51...

5 Configuration D-Link Web Smart Switch User Manual Configuration > 802.1Q VLAN (Asymmetric VLAN) This function is located in the 802.1Q Configuration page. It allows devices in different VLANs to communicate with the servers, firewalls or other shared resources in the shared VLAN. This configura...

5 Configuration D-Link Web Smart Switch User Manual shared ports and the set of ports to be separated from the other VLANs (for example, port 6 and 7 respectively). Therefore we have three VLANs that share some common ports, but their original membership ports are still separated from each other (fo...

5 Configuration D-Link Web Smart Switch User Manual Figure 67 – Configuration > 802.1Q Management VLAN Configuration > Voice VLAN > Voice VLAN Setting Voice VLAN is a feature that allows you to automatically place the voice traffic from IP phone to an assigned VLAN to enhance the VoIP servi...

5 Configuration D-Link Web Smart Switch User Manual Configuration > Voice VLAN > Voice VLAN OUI Setting This window allows the user to configure the user-defined voice traffic’s OUI. An Organizationally Unique Identifier (OUI) is the first three bytes of the MAC address. This identifier unique...

5 Configuration D-Link Web Smart Switch User Manual Figure 70 – Configuration > Link Aggregation > Port Trunking Auto Surveillance VLAN State: Select to enable or disable Auto Surveillance. The default is Enabled. VLAN ID: By default, the VLAN ID 1 was created as Surveillance VLAN and all port...

5 Configuration D-Link Web Smart Switch User Manual Configuration > Link Aggregation > Port Trunking The Trunking function enables the combining of two or more ports together to increase bandwidth. Up to eight Trunk groups may be created, and each group can be consisted of up to eight ports. S...

5 Configuration D-Link Web Smart Switch User Manual Active - Active LACP ports are capable of processing and sending LACP control frames. This allows LACP compliant devices to negotiate the aggregated link so the group may be changed dynamically as needs require. In order to utilize the ability to c...

5 Configuration D-Link Web Smart Switch User Manual Figure 77 – Configuration > Multicast Filtering Mode Configuration > Port Mirroring Port Mirroring is a method of monitoring network traffic that forwards a copy of each incoming and/or outgoing packet from one port of the Switch to another p...

5 Configuration D-Link Web Smart Switch User Manual Figure 79 – Configuration > Loopback Detection Loopback Detection State: Use the drop-down menu to enable or disable loopback detection. The default is Disabled. Interval (1-32767): Set a Loop detection Interval between 1 and 32767 seconds. The ...

5 Configuration D-Link Web Smart Switch User Manual Configuration > Spanning Tree > STP Port Settings STP can be set up on a port per port basis. In addition to setting Spanning Tree parameters for use on the switch level, the Switch allows for the configuration of groups of ports, each port-g...

5 Configuration D-Link Web Smart Switch User Manual Figure 85 – QoS > Bandwidth Control From Port / To Port: A consecutive group of ports may be configured starting with the selected port. Type: This drop-down menu allows you to select between RX (receive), TX (transmit), and Both . This setting ...

5 Configuration D-Link Web Smart Switch User Manual Figure 86 – QoS > 802.1p Default Priority By selecting the DSCP priority, the web pages will changes as seen below: Figure 87 – QoS > DSCP Priority Settings Select QoS Mode: D-Link Smart Switch allows the user to prioritize the traffic based ...

5 Configuration D-Link Web Smart Switch User Manual Security > Trusted Host Use Trusted Host function to manage the switch from a remote station. You can enter up to ten designated management stations networks by defining the IP address/Subnet Mask as seen in the figure below. Figure 88 Security ...

5 Configuration D-Link Web Smart Switch User Manual Security > 802.1X > 802.1X Settings Network switches provide easy and open access to resources by simply attaching a client PC. Unfortunately this automatic configuration also allows unauthorized personnel to easily intrude and possibly gain ...

5 Configuration D-Link Web Smart Switch User Manual Figure 97 – Monitoring > System Log ID: Displays an incremented counter of the System Log entry. The Maximum entries are 500. Time: Displays the time in days, hours, and minutes the log was entered. Log Description: Displays a description event ...

5 Configuration D-Link Web Smart Switch User Manual Service Type: Specify the type of service. The possible values are: Any - Indicates ACL action will be on packets from any service type. Ether type - Specifies an Ethernet type for filtering packets. ICMP All - Indicates ACL action will be on packe...

5 Configuration D-Link Web Smart Switch User Manual Delete: To delete an access profile. To manually add a profile, click Add ACL Profile : Figure 100 – Add Access Profile The steps of adding an access profile is like below: 1) After selecting the Profile ID and Frame Type (MAC or IPv4), specify att...

6 Command Line Interface D-Link Web Smart Switch User Manual 6 Command Line Interface The D-Link Web Smart Switch allows a computer or terminal to perform some basic monitoring and configuration tasks by using the Command Line Interface (CLI) via TELNET protocol. To connect a switch via TELNET: 1. M...

6 Command Line Interface D-Link Web Smart Switch User Manual firmware_fromTFTP Download and install new firmware on the Switch from a TFTP server. cfg_fromTFTP Download a switch configuration file from a TFTP server. tftp://ip-address/ The IP address of the TFTP server. filename The filename of the ...

6 Command Line Interface D-Link Web Smart Switch User Manual Logout This command closes the current connection. Syntax logout Example DES-1210-28P> logout Figure 115 – The logout command Ping This command checks if another IP address is reachable on the network. You can ping the IP address connec...

6 Command Line Interface D-Link Web Smart Switch User Manual Reset All configurations will be reset to the default settings. Syntax reset config Example DES-1210-28P> reset config % Device will reboot after reset configuration successfully. DES-1210-28P> Figure 118 – The reset config command S...

6 Command Line Interface D-Link Web Smart Switch User Manual Parameter Description <passwd> The new password of the administrator. Example DES-1210-28P> config account admin password admin DES-1210-28P> Figure 121 – The config account admin password command Save The command saves the con...

Appendix A - Ethernet Technology D-Link Web Smart Switch User Manual 72 Appendix A - Ethernet Technology This chapter will describe the features of the D-Link Web Smart Switch and provide some background information about Ethernet/Fast Ethernet/Gigabit Ethernet switching technology. Gigabit Ethernet...

Appendix B - Technical Specifications D-Link Web Smart Switch User Manual Appendix B - Technical Specifications Hardware Specifications Key Components / Performance Switching Capacity: - DES-1210-28: 12.8Gbps - DES-1210-52: 17.6Gbps - DES-1210-28P: 12.8Gbps Max. Forwarding Rate - DES-1210-28: 9.5Mpp...

Appendix B - Technical Specifications D-Link Web Smart Switch User Manual Supports Strict / WRR mode in queue handling Bandwidth Control Security 802.1X port-based access control Port Security IP and MAC ACL Broadcast Storm Control D-Link Safeguard Engine Trusted Host ARP Spoofing Prevention DHCP Se...

Appendix C – Rack mount Instructions D-Link Web Smart Switch User Manual Appendix C – Rack mount Instructions Safety Instructions - Rack Mount Instructions - The following or similar rack-mount instructions are included with the installation instructions: A) Elevated Operating Ambient - If installed...