Cub Cadet 60 - Manuals

Operation 1. Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet. 2. Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of a...

6 3 Setting Up Your Chipper Shredder Vacuum IMPORTANT: This unit is shipped without gasoline or oil in the engine. Be certain to service engine with gasoline and oil as instructed in the separate engine manual before operating your machine. Loose Parts In Carton a. Upper and Lower Handleb. Hose Asse...

3 Attaching The Hose Assembly 5. a. Slide hose adapter of hose assembly into the base adapter located on the left front of the Chipper shredder Vacuum. See Figure 3-4. b. Pull spring loaded pin out on the base and align pin with the first hole (closest to the end of the tube) in the hose adapter. c....

9 4 WARNING: Use extreme care when handling gasoline. Gasoline is ex-tremely flammable and the vapors are explosive. Never fuel machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes, and other sources of ignition. Gas and Oil Fill-Up 1. Check oil level and add o...

11 4 Figure 4-6 IMPORTANT: The flail screen is located inside the housing in the discharge area. If the flail screen becomes clogged, remove and clean as instructed in MAINTAIN-ING YOUR CHIPPER SHREDDER VACUUM. For best performance, it is also important to keep the chipper blade sharp. Using The Hos...

1 WARNING: Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine. General Recommendations Always observe safety rules when performing any maintenance.The warranty on this chipper/shredder vacuum does not cov...

13 Maintaining Your Chipper Shredder Vacuum Figure 5-1 Figure 5-2 WARNING: Before performing any type of maintenance on the machine, wait for all parts to stop moving and disconnect the spark plug wire. Failure to follow this instruction could result in personal injury or property damage. Removing t...

1 Carefully tilt and support the unit up to provide access underneath to the nozzle mounting hardware and impeller. Remove the three shoulder bolts securing the black plastic lower flail housing to the lower housing. Refer to Figure 5-6.Tilt top of black plastic lower flail housing toward the engine...

16 For repairs beyond the minor adjustments listed here, contact an authorized service dealer. 6 Trouble Shooting Cause Problem Remedy Engine fails to start 1. Throttle lever not in correct starting position. 2. Spark plug wire disconnected.3. Choke not in CHOKE position (if equipped). 4. Fuel tank ...

1 NOTES Use this page to make notes and write down important information.

19 Parts List To order replacement parts, call the Customer Dealer Referral Line at 1-877-282-8684, or visit www.cubcadet.com to find the nearest Cub Cadet service dealer in your area. G E N U I N E FA C TO RY PA R TS Ref. No. Part No. Description 1. 736-0314 Thrust Washer.375 ID x.70 OD 2. 749-0417...

GDOC-100097 REV. A Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-8-8-8684 MTD Canada Limited - KITCHENER, ON NG 4J1; Phone 1-800-668-138 The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its p...

CUB CADET LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 PRINTED IN U.S.A Aspiradora Para Patios - Modelo Serie 060 Seguridad•Ensamblaje•Operación•Consejos y Técnicas•Mantenimiento•Solución de problemas•Lista de Parte•Grantías MANUAL DEL OPERADOR IMPORTANTE LEA CON ATENCIÓN LAS REGLAS DE SEGURIDAD ...

4 Búsqueda y registro del número de modelo Por favor, NO devuelva la unidad al minorista a quien se la adquirió sin contactarse primero con el Departamento de Asistencia al Cliente. Índice ANTES DE COMENZAR A ENSAMBLAR SU NUEVO EQUIPO, por favor localice la placa del modelo en el equipo y copie la i...

1 Etiquetas de seguridad ADVERTENCIA: NO retire las etiquetas de seguridad de la aspiradora para patios. Etiquetas de Seguridad Encontradas En Su Aspiradora Para Patios TO AVOID SERIOUS INJURY • READ OPERATOR'S MANUAL.• KEEP HANDS OUT OF INLET AND DISCHARGE OPENINGS WHILE MACHINE IS RUNNING. ROTATIN...

6 Prácticas de seguridad en la operación ADVERTENCIA: El escape del motor de este producto, algunos de sus componentes y algunos componentes del vehículo contienen o emiten productos químicos que el estado de California considera que pueden producir cáncer, defectos de nacimiento u otros problemas r...

Prácticas de seguridad en la operación ADVERTENCIA: Este símbolo in- dica instrucciones de seguridad importantes que de no seguirse, se podría poner en peligro la seguridad personal y/o la propiedad suya y de terceros. Lea y siga todas las instrucciones en este manual antes de iniciar la operación d...

8 IMPORTANTE: Esta unidad se envía sin gasolina ni aceite en el motor. Antes de operar la máquina cargue el motor con gasolina y aceite como se indica en el manual separado del mismo. Piezas Sueltas Dentro de la Caja (Vea la figura 3-1) Manija superior e inferiorMontaje de la mangueraBolsaAnteojos d...

30 Figura 4-1 Ahora que ya ha ajustado su aspiradora para patios para la operación, familiarícese con sus controles y características. Estos se describen y se ilustran en esta página. Este conocimiento le permitirá utilizar su nuevo equipo a su máxima capacidad. ADVERTENCIA: Al operar una corta-dora...

31 Mandos de Motor Ver el manual de motor separado para la posición y la función de los mandos en el motor. ADVERTENCIA: Tenga extremo cuidado cuando manipule la gasolina. La gasolina es altamente inflamable y los vapores son explosivos. Nunca le agregue combustible a la máquina en interiores o mien...

33 IMPORTANTE: La pantalla de desgranado está ubicada dentro de la caja en la zona de descarga. Si se tapa la pantalla de desgranado, sáquela y límpiela como se indica en la sección de mantenimiento. Para obtener el mejor resultado es importante también mantener afilada la hoja de la cortadora. Uso ...

34 ADVERTENCIA: Detenga siempre el motor, desconecte la bujía y haga masa contra el motor antes de limpiar, lubricar o de realizar todo tipo de mantenimiento de la máquina. Recomendaciones Generales Respete siempre las reglas de seguridad cuando realice tareas de mantenimiento.La garantía de esta as...

38 Si debe realizar reparaciones más importantes que las enunciadas aquí, comuníquese con el distribuidor local autorizado. 6 Solución de problemas Causa Problema Remedio El motor no arranca La palanca del regulador no está en la posición de arranque correcta. La palanca de obturación no está en la ...

GDOC-100097 REV. A Cub Cadet LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Teléfono: 1-8-8-8684 MTD Canada Limited - KITCHENER, ON NG 4J1; teléfono 1-800-668-138 La siguiente garantía limitada es otorgada por Cub Cadet LLC con respecto a nuevos productos adquiridos y utilizados en Estados Unidos,...

Operation 1. Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet. 2. Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of a...

6 NOTE: This Operators Manual covers a range of product specifications for various models. Characteristics and fea-tures discussed and /or illustrated in this manual may not be applicable to all models. Cub Cadet reserves the right to change product specifications, designs and equipment without noti...

Figure 3- Figure 3-3 Figure 3-4 Attaching The Handle 1. Remove the hairpin clips from the handle brackets and remove the carriage screws and wing nuts from the lower handle.a. Place the bottom holes in lower handle over the pins on the handle brackets and secure with hairpin clips. See Figure 3-2. b...

10 Figure 4-1 Now that you have set up your yard vacuum for operation, get acquainted with its controls and features. These are described below and illustrated on this page. This knowledge will allow you to use your new equip-ment to its fullest potential. WARNING: The operation of any chipper shred...

11 Blower Chute When attached to unit, the blower chute is used to blow or scatter yard waste such as leaves, pine needle, or small twigs across yard. WARNING: The operation of the Yard Vacuum can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear ...

1 To Remove Blower Chute 1. Grasp blower chute with one hand and pull lock rod on mounting bracket with other hand toward engine to release. Refer to Figure 8 on page 9. 2. Remove blower chute from rim of the discharge opening. Yard waste such as leaves and pine needles can be vacuumed up for shredd...

13 Using The Hose Assembly 1. Place nozzle/hose vac handle in the bottom position on the nozzle to redirect vacuum to the hose assem-bly. See Figure 4-5. 2. The spring loaded pin must be in the second hole of the hose adapter to operate the hose assembly. 3. Unhook the hose from upper handle bracket...

14 Maintaining Your Yard Vacuum WARNING Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine. Figure -1 Figure - WARNING: Always stop engine, disconnect spark plug, and ground against engine before cleaning...

1 WARNING Figure -3 Figure -4 The chipper blade is sharp. When sharp-ening blade, wear leather work gloves to protect your hands and follow the origi-nal angle of grind. Maintaining Your Yard Vacuum 3. Remove the front hubcaps, flange lock nuts, front wheels, and wave washers that attach to the pivo...

16 For repairs beyond the minor adjustments listed here, contact an authorized service dealer. 6 Trouble Shooting Cause Problem Remedy Engine fails to start 1. Throttle lever not in correct starting position. 2. Spark plug wire disconnected.3. Choke not in CHOKE position (if equipped). 4. Fuel tank ...

1 Parts List Ref. Part No. Description 1. 731-0982A Radial Spoke Hubcap 2. 749-04172 Upper Handle 3. 720-0279 Knob 4. 710-0599 Screw, 1/4-20 x.500 5. 710-1205 Eye Bolt 6. 781-1056 Upper Handle Bracket 7. 710-0726 Hex Cap Screw 5/16-12 x.750 8. 720-04072 Star Knob 5/16-18 9. 710-1174 Carriage Bolt 10...

The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possessions and territories.“Cub Cadet” warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date o...