Cub Cadet 60 - User Manual

Operation 1. Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet. 2. Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of a...

6 NOTE: This Operators Manual covers a range of product specifications for various models. Characteristics and fea-tures discussed and /or illustrated in this manual may not be applicable to all models. Cub Cadet reserves the right to change product specifications, designs and equipment without noti...

Figure 3- Figure 3-3 Figure 3-4 Attaching The Handle 1. Remove the hairpin clips from the handle brackets and remove the carriage screws and wing nuts from the lower handle.a. Place the bottom holes in lower handle over the pins on the handle brackets and secure with hairpin clips. See Figure 3-2. b...

10 Figure 4-1 Now that you have set up your yard vacuum for operation, get acquainted with its controls and features. These are described below and illustrated on this page. This knowledge will allow you to use your new equip-ment to its fullest potential. WARNING: The operation of any chipper shred...

11 Blower Chute When attached to unit, the blower chute is used to blow or scatter yard waste such as leaves, pine needle, or small twigs across yard. WARNING: The operation of the Yard Vacuum can result in foreign objects being thrown into the eyes, which can damage your eyes severely. Always wear ...

1 To Remove Blower Chute 1. Grasp blower chute with one hand and pull lock rod on mounting bracket with other hand toward engine to release. Refer to Figure 8 on page 9. 2. Remove blower chute from rim of the discharge opening. Yard waste such as leaves and pine needles can be vacuumed up for shredd...

13 Using The Hose Assembly 1. Place nozzle/hose vac handle in the bottom position on the nozzle to redirect vacuum to the hose assem-bly. See Figure 4-5. 2. The spring loaded pin must be in the second hole of the hose adapter to operate the hose assembly. 3. Unhook the hose from upper handle bracket...

14 Maintaining Your Yard Vacuum WARNING Always stop engine, disconnect spark plug, and ground against engine before cleaning, lubricating or doing any kind of maintenance on your machine. Figure -1 Figure - WARNING: Always stop engine, disconnect spark plug, and ground against engine before cleaning...

1 WARNING Figure -3 Figure -4 The chipper blade is sharp. When sharp-ening blade, wear leather work gloves to protect your hands and follow the origi-nal angle of grind. Maintaining Your Yard Vacuum 3. Remove the front hubcaps, flange lock nuts, front wheels, and wave washers that attach to the pivo...

16 For repairs beyond the minor adjustments listed here, contact an authorized service dealer. 6 Trouble Shooting Cause Problem Remedy Engine fails to start 1. Throttle lever not in correct starting position. 2. Spark plug wire disconnected.3. Choke not in CHOKE position (if equipped). 4. Fuel tank ...

1 Parts List Ref. Part No. Description 1. 731-0982A Radial Spoke Hubcap 2. 749-04172 Upper Handle 3. 720-0279 Knob 4. 710-0599 Screw, 1/4-20 x.500 5. 710-1205 Eye Bolt 6. 781-1056 Upper Handle Bracket 7. 710-0726 Hex Cap Screw 5/16-12 x.750 8. 720-04072 Star Knob 5/16-18 9. 710-1174 Carriage Bolt 10...

The limited warranty set forth below is given by Cub Cadet LLC with respect to new merchandise purchased and used in the United States, its possessions and territories.“Cub Cadet” warrants this product against defects in material and workmanship for a period of two (2) years commencing on the date o...