Creda W120VW - Manuals - manualsarea.com

Page 2 - Positioning & Adjusting the feet; Recycling & Disposal Information; Electrical Requirements; Contents

Positioning & Adjusting the feet Choosing the position of your appliance will influence its performance. ★ Position where possible on a solid floor. Some vibration may occur with a wooden floor. ★ Take care with vinyl floor coverings. The weight of the appliance may cause indentations insome vin...

Page 3 - Connecting to the Water Supply; Removing the Polystyrene Pyramid

Hot and Cold Fill Connection 1. Connect the straight end of the supplied RED or GREY hose to the HOT water supply tap (Fig 1). Connect the straight end ofthe supplied BLUE hose to the COLD water supply tap. 2. Hand tighten connectors sufficiently to ensure water does not leak from the hose connectio...

Page 4 - Connect to a drainage system; Into a Standpipe; Into a Sink Waste System

4 Connect to a drainage system ● Do not remove hooked end support from drainage hose. ● Do not position standpipe near an electrical outlet. For drainage into a standard work top sink ensure outlet pipe has a minimum bore of32 mm. To avoid syphoning ensure the end of the drainage hose is above the w...

Page 5 - Washcare Tips; Interlocking Door System; Front; Getting to know your machine; Cotton Load; Or

14 Washcare Tips ★ We strongly recommend that your do not wash underwired bras in this machine. Should the wires become detached they could cause damage to your clothes and the machine. If the washcare label states that the garmentis machine washable then we advise placing it in a sealed pillow case...

Page 6 - A typical wash programme

1. Sort laundry into same wash requirements. 4. Select wash programme by turningthe wash dial clockwise. 5. Select optional wash features by pressing required button. 2. Close door, applying pressure only atthe 2 o’clock position. 7. Check water and electricity are switched on at mains. A typical wa...

Page 8 - Choosing a wash programme; Prewash; Incoming

Choosing a wash programme 8 ITCL Prog. Codes Temp ˚C 40 3kg to 5.5kg 15 - 25 400 Full Load Approx Prog.Time (mins) based on hot and cold fill Maximum Spin Speed (rpm) depending on Model Fabric A Prewash Heavily soiled loads. On completion, switch‘OFF’ mains button before selecting wash programme. WA...

Page 9 - BUTTON SELECTION; ENERGY SAVE; DEEP RINSE; Optional wash features; PULSE SPIN; INTELLIGENT CARE

9 BUTTON SELECTION To select, press the button and the button comes out. To cancel, press again and the button is flush withthe console.Remember to cancel buttons after use! ENERGY SAVE Save money and time on lightly soiled loads. Lightly soiled loads are washed at the temperature of the incoming ho...

Page 10 - CHOOSE A SUITABLE DETERGENT; The Dispenser Drawer

CHOOSE A SUITABLE DETERGENT ★ Select ‘low suds’ automatic washing powder, designed specifically for automatic washing machines or washer dryers. ★ Follow manufacturer’s dosage recommendations. Do not under dose, you will not achieve a clean wash. ★ You will need up to 50% more detergent in hard wate...

Page 12 - Care and Cleaning

WARNING ● Do not clean any part of your appliance with abrasive cleaners, scouring agents, acids, chlorine based bleach or metal polish as they may cause damage. Care and Cleaning Maintenance wash 12 C L E A N I N G T H E E X T E R I O R R E M OV I N G A N D C L E A N I N G T H E D I S P E N S E R D...

Page 13 - © REPRODUCED BY KIND PERMISSION OF LEVER BROS. LIMITED; Regular Checks and Stain Removal; Regular checks; Stain Removal

© REPRODUCED BY KIND PERMISSION OF LEVER BROS. LIMITED Regular Checks and Stain Removal Regular checks As with any major appliance, there are certain aspects whichrequire regular attention. Listed below are a number of such keyareas which you should check regularly.Before calling out aservice engine...

Page 14 - Something wrong with your appliance

14 Before calling your nearest Service Office, look at this list, to find a possible solution to your problem. My appliance will not fill or take in detergent... ★ Is the machine plugged in and switched on? ★ Is the socket OK? Try another appliance in the socket. ★ Is the fuse in the machine plug OK...

Page 15 - Creda Service Cover

The cost of parts where required will be charged additionalto the fixed labour charge, but again this cost will have amaximum level of which you will be advised by your RegionalService Centre. The repair itself is fully guaranteed for 12months. CREDA CARE LEVEL 2: Annual fee payable all inclusivecov...

Page 16 - Key Contacts; Service

For more information on our exciting product range ring Creda Answer Centre 08701 54 64 74 016437794-02 Printed by SIMLEX • FOUR ASHES, WOLVERHAMPTON Key Contacts Service UK: 08709 066 066 Republic of Ireland: 1850 302 200 Genuine Spares & Accessories Mail Order Hotline UK: 08709 077 077 Republi...