COZY W505F - Manuals

VENTING This appliance must be properly connected to a venting system. Consult local ordinances governing venting. Install only UL listed type BW 4” oval gas vent. When the vent enters theattic, a listed type B-1 round flue pipe may be used. See Figure2, Page 7. Vent pipe must connect to the wall fu...

ROUGH-IN INSTRUCTIONS NOTE: Maximum wall thickness for a dualwall (W505, W506) installation is 5-3/8”. STEP 1. Attach the base plate (purchased with the vent pipe) to the header plateusing two No. 8 sheet-metal screwsthrough the pre-punched holes. Theheater may not vent properly without abase plate ...

B-W VENT FIGURE 3 Casing “Z BracketFront Panel FrontPanel Door FIGURE 5C INSTALLATION STEP 6. To place furnace into position, grasp furnace and lift so furnace flue vent and headerplate vent opening engage. Do not use burner orgas control to lift heater. Lift furnace upward andswing bottom into wall...

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improperand dangerous operation. Verify proper operationafter servicing. WIRING INSTRUCTIONS – GRAVITY WALL FURNACE WARNING: Failure to locate the thermostat properly or to wire the furnace correctly may...

A. This appliance has a pilot which must be lightedby hand. When lighting the pilot, follow these in-structions exactly. B. B E F O R E L I G H T I N G s m e l l a l l a r o u n d t h eappliance area for gas. Be sure to smell next to thefloor because some gas is heavier than air and willsettle on th...

PILOT ADJUSTMENT Locate the pilot adjustment screw on the valve. The pilotflame should surround at least the top 3/8” of the powerpile(pilot generator) or thermocouple (see below). The pilot isunregulated so it will be operating at inlet line pressure (Max.7” w.c. for natural gas and 11” w.c. for pr...

BBSK INSTALLATION INSTRUCTIONS STEP 1 . Select left or right side of front panel for most convenient location of the temperature control knob. Rememberto choose the side that allows adequate clearance for accessibility to adjust the control knob. STEP 2 . On selected side, locate three (3) vertical ...

BBSK KIT LIGHTING INSTRUCTIONS FOR YOUR SAFETY READ BEFORE LIGHTING A. This appliance has a pilot which must be lighted byhand. When lighting the pilot, follow these instruc-tions exactly. B. B E F O R E L I G H T I N G s m e l l a l l a r o u n d t h eappliance area for gas. Be sure to smell next t...

Page 16 MODEL WFF81-C OPTIONAL FAN KIT INSTALLATION INSTRUCTIONS NOTE: This fan kit is to be installed after installation of wall furnace and with the wall furnace front panel in place. STEP 1 . This appliance, when installed, must be electrically grounded in accordance with local codes, or inthe ab...

Ground WHITE BLACK L2 White115 VAC L1 Black115 VAC BLACK FAN SWITCH BLACK BLACK BLACK MOTOR WHITE GREEN GROUND WIRE L2White L1Black 115 VAC 60 HZ - Less than 12 Amps. If any of the original wire assupplied with this appliance must be replaced, it must be replaced withtype thermoplastic 105 degree C ...

40542-A REAR REGISTER KIT (Optional Accessory) INSTALLATION INSTRUCTIONS FOR GRAVITY VENTED WALL FURNACES STEP 1. Cut hole within stud space behind heater in the back wall 8-1/4” high by 12-5/8” wide. The loweredge of the hole to be 45-3/4” above the floor plate or 47” from the floor (with standard ...

TROUBLE SHOOTING CHART for qualified serviceman - MAIN BURNER SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION Flame too large 1. Defective operator section of gas valve. 1. Replace complete valve. 2. Burner orifice too large. 2. Check with local gas company for proper orifice size and replace. 3. If insta...

SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION Burner won’t 1. Pilot flame too large or too small. 1. Re-adjust pilot flame using adjustment on turn on combination control valve. 2. Dirt in pilot orifice. 2. Clean pilot orifice with air or solvent, do not ream. 3. Defective automatic pilot section in 3. ...

SINGLE WALL FURNACE Model NumbersNat. L.P. W255F W256F W355F W356F DUAL WALL FURNACE Model NumbersNat. L.P. W505F W506F NOTICE: When ordering any component in the Burner Assembly,specify either Honeywell or Robertshaw components. REV. 06/2006 Prices and specifications subjectto change without notice...

LIMITED WARRANTY The Louisville Tin & Stove Co. warrants to the original user the accompanying product for the period specified herein, provided said product is installed, operated, maintained, serviced, and used according to the instructions and specifications accompanying the product. AS OUTLI...