COZY HEDV403 - Manuals - manualsarea.com

Page 2 - CONTENTS; INTRODUCTION; SPECIFICATIONS AND DIMENSIONS

Page 2 Introduction…………………………….. 2 Specifications and Dimensions…………. 2 Safety Rules…………………………….. 3 Clearances………………………………. 4/5 Location………………………………… 6 Installation……………………………… 7 Lighting Instructions…………………… 10 Pilot Adjustment……………………….. 11 Burner Orifice………………………….. 11 Wiring Diagram………………………… 12...

Page 4 - VENT TERMINAL CLEARANCES; Vent Terminal

REFERENCE LETTER TO DRAWING CANADIAN INSTALLATIONS¹ A = Clearance above grade, veranda, porch, deck, or balcony 12 Inches (30 cm) B = Clearance to window or door that may be opened 12 Inches (30 cm) C = Clearance to permanently closed window 12 Inches (30 cm) D = Vertical clearance to ventilated sof...

Page 5 - Ceiling or Overhang

Page 5 CLEARANCES 1. As you face the heater, the clearance to a side wall on the right side is 0” (Fig. 1), and the left side is 1”(Fig. 2). 2. The minimum clearance from the top of the heater to the ceiling or any projecting overhang is 10”. (See Figure 3). 3. The minimum clearance from the bottom ...

Page 6 - 2” Minimum above grade

CLEARANCES 7. RESIDENTIAL GARAGE INSTALLATION: Gas utilization equipment in residential garagesshall be installed so that all burners and burner ignition devices are located not less than 18 inches(46 cm) above the floor. You must build a platform 18” above floor, the full width and depth ofthe heat...

Page 7 - INSTALLATION; Locate studs on each side of this area.; FIGURE 6; FIGURE 7

INSTALLATION Failure to follow these instructions carefully could result in poor performance, property damage, personal injury, ordeath. STEP 1. LOCATE VENT OPENING (Requires 3-1/2” diameter wall opening)a) Select area on wall where heater will be installed. Using template (packed with heater) mark ...

Page 8 - INSTALLATION - CONTINUED; BRACKETS

INSTALLATION - CONTINUED STEP 3 INSTALLING VENT SYSTEM 5” - 32” WALL THICKNESS (12.7 cm - 81.3 cm)a) Use only factory supplied parts. Do not attempt to modify in any way. To do so could cause a systemimbalance resulting in poor performance and/or unsafe operating conditions. b) Slide collection box ...

Page 9 - Temperature Sensing Unit

STEP 5. INSTALLING REAR TRIM KITa) Secure right and left trim kit sides to the wall and trim kit brackets with eight #8 screws provided. Seefigure 11. The back of the heater should now be spaced 5” from the wall. b) Remove the temperature sensing unit from the back of the heater. Save the nylon atta...

Page 11 - Turn off all electrical supply to heater.

MODEL 0 to 2 , 0 0 0 ’ 4 , 0 0 0 ’ 6 , 0 0 0 ’ 8,000’ - NO. 2 , 0 0 0 ’ 4 , 0 0 0 ’ 6 , 0 0 0 ’ 8 , 0 0 0 ’ 1 0 , 0 0 0 ’ NATURAL GAS HEDV403 4 5 4 7 4 8 4 9 5 0 L.P. GAS HEDV404 5 5 5 5 5 6 5 6 5 7 PROPER BURNER FLAME The burner flame may be observed by raising the sightglass cover. A proper flame ...

Page 12 - WIRING; C wire or its equivalent.; WARNING

WIRING This appliance is equipped with a three prong groundingplug. For your protection against shock hazard, this ap-pliance should be plugged directly into a properly groundedthree-prong receptacle. Do not cut or remove the ground-ing prong from this plug. NOTE: If any of the original wire supplie...

Page 14 - CONTENTS OF KIT

HEVK-5 5’ VENT EXHAUST KIT INSTALLATION INSTRUCTIONS WARNING: Use only Louisville Tin & Stove Company factory supplied parts and kits. Failure to do so could result inloss of life, personal injury, property damage, or unsatisfactory performance. CONTENTS OF KIT 1 only P/N 72532 2”x3” Steel Coupl...

Page 15 - ELBOW KIT; Elbow 2”

HEVE-5 VENT ENCLOSURE KIT INSTALLATION INSTRUCTIONS STEP 1) Position end of Part No. 41610 enclosure body to heater trim kit where pipes exit trim kit, centeringpipes inside body and attach to wall. Wall anchors, not provided, may be required. Collector box maybe behind HEVE-5 Kit. STEP 2) Cut to fi...

Page 17 - Flame too large

TROUBLE SHOOTING CHART SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION Flame too large 1. Defective operator section of valve. 1. Replace valve. 2. Burner orifice too large. 2. Check with local gas company for proper orifice - size and replace. 3. If installed above 2,000 ft. 3. See burner orifice section...

Page 18 - TROUBLE SHOOTING CONTROL BOARD; Reason for Indication

TROUBLE SHOOTING CONTROL BOARD To improve diagnosing and servicing, this control board is equipped with a self diagnosinggreen status light (see wiring diagram). To indicate stand by mode and proper operationthis light will remain on. If there should be a malfunction, the light will flash a varyingn...

Page 19 - Prices and specifications subject

HI-EFFICIENT DIRECT VENT WALL FURNACE Prices and specifications subject to change without notice. All prices are F.O.B. factory. Page 19 MODEL NUMBERSHEDV403 - NAT. GASHEDV404 - L.P. GAS 46 52 48 33 34 37 36 35 43 41 40 39 38 42 31 47 27 26 50 25 24 23 22 21 20 49 30 53 29 28 32 8 9 10 11 12 13 14 1...

Page 20 - Model Number HEDV403 HEDV404

Page 20 MARCH 2005 HOW TO PROPERLY ORDER PARTS: In addition to part description and part number, please give model number, serial number, and type of gas used. This information can be found on the rating plate that is attached to heater. Mr. Contractor, we only sell parts through our wholesalers, bu...

Page 21 - IMPORTANT SAFETY BULLETIN ON YOUR GAS CONTROL AND PILOT LIGHT; Do not try to light any appliance.

YOUR GAS CONTROL AND PILOT LIGHT SYSTEM Your gas control and pilot light system has a safetydevice whose purpose is to shut-off the gas supplyto the appliance if the pilot light goes out. If youhave trouble lighting the pilot or keeping it lit, itmay mean that this safety device is warning yout h a ...

Page 22 - LOUISVILLE TIN AND STOVE COMPANY

The Louisville Tin & Stove Co. warrants to the original user the accompanying product for the periodspecified herein, provided said product is installed,operated, maintained, serviced, and used according to theinstructions and specifications accompanying the product.AS OUTLINED IN OUR INSTRUCTIO...