Page 2 - MODELS WITH LOW-BTU STANDING PILOT
CONTENTS Contents……………………………………………........... 2Introduction…………………………………………. 2Specifications……………………………………….. 2Safety Rules………………………………………… 3Helpful Installation Information……………….........…. 3Connecting the Vent……………………………....…..… 3,4Combustion and Ventilation Air.......................................
Page 3 - SAFETY RULES; Adequate air for combustion and venting must be provided.; READ CAREFULLY BEFORE INSTALLING UNIT
SAFETY RULES 1. Improper installation, adjustment, alteration, service or maintenance can cause property damage, bodily injury or death. If youdo not understand these instructions or your local codes, call local authorities, a qualified installer, service agency, gas supplier,or the manufacturer. 2....
Page 4 - FIGURE A
VENTING - CONTINUED This appliance is equipped with a blocked flue switch. WARNING: Do not bypass the blocked flue switch. Todo so could expose the consumer to property damage,personal injury or possible death. This switch, when activated, will interrupt the electrical circuit betweenthe transformer...
Page 5 - COMBUSTION AND VENTILATION AIR
COMBUSTION AND VENTILATION AIR When installed, this gas appliance must be provided with freshair for combustion, ventilation, and dilution of hot flue gases.The minimum required volume of the area where the appliance isinstalled should be 50 cubic feet per 1,000 btu/hr. If installed in an area of th...
Page 6 - Side Wall; MODEL NUMBER; ” Minimum; FIGURE 2; Header Plate; FIGURE 3
LOCATION AND SPECIAL PRECAUTIONS The wall furnace should be located near the center ofthe house for best heat distribution. If the area where the appliance is to be installed containscarpeting, tile or combustible materials, other than woodflooring, the appliance shall be installed on a metal plate,...
Page 8 - INSTALLATION; FIGURE 6
INSTALLATION / WHEN RECESSED (UP TO 9-1/4”) STEP 1. Cut out floor plate between 2x4 studs, so heater will set flat on floor. STEP 2. Make electrical connection of 115 V. wiring into junction box provided on top of header plate. STEP 3. Attach the base plate (purchased with the vent pipe) to the head...
Page 9 - FIGURE B; CONTROLS; NATURAL GAS; SPECIFIC ELEVATIONS; PILOT ADJUSTMENT; STANDING PILOT
Installation of B-W Gas Ventfor one-story buildings or forfirst floor of multi-storybuildings. Ceiling plate spacers to centerB-W Gas Vent in stud space -nail securely at both ends. Plate cut away for fullwidth of stud space toprovide ventilation. Studs on16 inch centers Sheet metal screw baseplate ...
Page 10 - causing property damage, personal injury or loss of life.; LIGHTING INSTRUCTIONS; PILOT BURNER
CF353C, CF354C, CF503C, CF504C, CF653C, CF654C - - STANDING PILOT FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot, which must be light...
Page 11 - TO TURN OFF GAS TO APPLIANCE
CF357C, CF358C, CF557C, CF558C - I.I.D. PILOT FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may resultcausing property damage, personal injury or loss of life. A. This appliance is equipped with an ignition device which automatical...
Page 13 - TERMINAL BLOCK WIRING DIAGRAM; AUXILIARY LIMIT SWITCH; the heating season or as often as needed.
TERMINAL BLOCK WIRING DIAGRAM CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improperand dangerous operation. Verify proper operation after servicing. AUXILIARY LIMIT SWITCH For your safety this furnace is equipped with a manual reset auxiliary limit...
Page 15 - CF357C, CF358C I.I.D. CF557C, CF558C
CF357C, CF358C I.I.D. CF557C, CF558C THERMOSTAT POWERCORD WHITE BLACK BLACK BLACK BLACK BROWN BROWN BLUE BLUE TRANSFORMER LIMIT SWITCH FAN SWITCH PILOT SPILLSWITCH AUXILIARYLIMIT SWITCH GAS VALVE BLACK GREEN WHITE WHITE BLACK BLACK BLACK BLACK MOTOR PCM TH PVSense MVMV/PV TR GND IGN IGNITIONMODULE B...
Page 16 - ROUGH-INS FOR REAR OR SIDE DISCHARGE; Install plastergrounds as shown in Figure 12 and Figure 13.; OPTIONAL ACCESSORY KITS
ROUGH-INS FOR REAR OR SIDE DISCHARGE Install plastergrounds as shown in Figure 12 and Figure 13. NOTE: When side discharge is being used, furnace should be set exactly 4” from side wall. 14-3/8” 10-3/ 16” PlasterGround SIDE FIGURE 13 REAR FIGURE 12 OPTIONAL ACCESSORY KITS REAR REGISTER KIT (Flush Mo...
Page 17 - SIDE DISCHARGE ON CASING; OPTIONAL KITS - CONTINUED; MODEL
SIDE DISCHARGE ON CASING 1. Use optional kit No. 306SR-A. 2. Cut out and remove embossed area on casing side. 3. Remove knockout from inner liner. 4. Place 1-1/2” boot from kit through opening, matchingflanges of boot to knockout on inner boot. 5. Mark screw holes and remove boot. 6. Drill holes wit...
Page 18 - TROUBLE SHOOTING CHART - PILOT AND VALVE
SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION Flame too large 1. Defective operator section of gas valve. 1. Replace complete valve. 2. Burner orifice too large. 2. Check with local gas company for proper orifice size and replace. 3. If installed above 2,000 ft. 3. Refer to orifice chart on Page 9. Nois...
Page 19 - TROUBLE SHOOTING CHART - PILOT AND VALVE - CONTINUED
SYMPTOM POSSIBLE CAUSES CORRECTIVE ACTION Pilot won’t light, 1. Air in line. 1. Bleed line. or stay lit 2. Defective thermocouple. 2. Replace thermocouple. (STANDING PILOT) 3. Pilot flame too low. 3. Adjust pilot flame. 4. Manual reset switch not engaged. 4. Push on button. Pilot won’t light, 1. Spa...
Page 20 - COUNTERFLOW WALL FURNACE / STANDING PILOT; CONTROL ASSEMBLY
REV. 04/97 COUNTERFLOW WALL FURNACE / STANDING PILOT Prices and specifications subject tochange without notice. Allprices are F.O.B. factory. MODELS: NAT. GAS L.P. GAS CF353C-R CF354C-R CF503C-R CF504C-R CF653C-R CF654C-R CONTROL ASSEMBLY Page 20 21 17 18 16 36 42 22/23 26 24 14 25 34 5 10 11 4 27 2...
Page 23 - 4 VOLT SYSTEM WITH INTERMITTENT
24 VOLT SYSTEM WITH INTERMITTENT N AT U R A L CF357C-R CF557C-R MODEL NUMBERS L . P. CF358C -R CF558C-R REF. PART LIST PART LIST PART DESCRIPTION NUMBER NUMBER PRICE NUMBER PRICE Casing Side, Right 1 3 0 0 5 5 $48.40 3 0 5 2 5 $52.10 Casing Side, Left 1 a 3 0 0 6 0 $48.40 3 0 5 3 0 $52.10 Center Bac...
Page 25 - PARTS LIST FOR ACCESSORIES FOR COUNTERFLOW WALL FURNACE; REPLACEMENT WIRING - STANDING PILOT COUNTERFLOW
PARTS LIST FOR ACCESSORIES FOR COUNTERFLOW WALL FURNACE PART DESCRIPTION REF. NO. PART NO. LIST PRICE 16" Vent Enclosure Side 1 31360 $8.20 16" Vent Enclosure Front 2 31355 $10.30 24" Vent Enclosure Side 1 31367 $12.60 24" Vent Enclosure Front 2 31366 $15.40 36" Vent Enclosure Si...
Page 26 - TAMPERING IS DANGEROUS
IMPORTANT SAFETY BULLETIN ON YOUR GAS CONTROL AND PILOT LIGHT SYSTEM FOR HEATING EQUIPMENT WHAT YOU DON’T KNOW CAN HURT YOU. Your pilot light system has been designed for safe and reliable operation. Although safety mechanisms are built-in,the potential for hazard exists. This information is intende...
Page 27 - LOUISVILLE TIN AND STOVE COMPANY
LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY LIMITED WARRANTY The Louisville Tin & Stove Co. warrants to the original user the accompanying product for the periodspecified herein, provided said product is installed,operated, maintained, serviced, and used according tothe i...