Coleman 9992-449 - Manuals - manualsarea.com

Page 2 - Pipe Sealant; Liquid Propane Gas Conversion Instructions

Item No. Qty Description 1 9992-4421 1 Main Burner Valve & Manifold Assembly (L.P.) 8350 2 47310103 1 Main Regulator Hose Assembly (L.P.) 3 08006001 1 Rear IR L.P. Orifice (8350) 4 08138381 1 Connector 3/8" FNPT x 3/8" MFLR 5 49900004 1 Pipe Sealant 6 9992-462 1 LP Conversion Sticker Liq...

Page 3 - * socket set with extension can also be used.

Tools Needed: Phillips head screwdriver1/4" nut driver *9/16" wrenchAdjustable wrench Fig 4 Fig 1 Fig 2 Fig 3 Rear Heat Shield Screws Heat Tents Screws * socket set with extension can also be used. Be sure gas supply is off, the knobs are in the offposition and the grill is cool. 1. Remove c...

Page 4 - Remove the screws from the bottom of the heat

Fig 5 Fig 6 Side Screws (Repeat on left side) Screws under lip Fig 8 Fig 7 Tabs 5. Remove the screws from the bottom of the heat shield, holding the front heat shield in place. Thescrews are located under the bottom lip of theshield (Fig. 5). 6. Remove the side heat shield screws located under the b...

Page 5 - Disconnect the right side flexline from the

Fig 10 Fig 14 Fig 9 Fig 11 Fig 13 Manifold Gas Inlet Flex Line Flex Line Fig 12 Manifold Screws 10. Disconnect the right side flexline from the manifold using the adjustable wrench. This willfree up the right side of the manifold (Fig. 9). 11. Disconnect the left side flexline from the back infrared...

Page 6 - You are now ready to install

Fig 15 Control Knob Stems You are now ready to install the new LP manifold. 16. NOTE: New screws for the bezels are inserted into the new LP manifold at the factory. Removethem before proceeding with Step 17. 17. Place the new manifold into the grill body with the control knob stems going outward th...

Page 7 - Remove the NG regulator from the main gas; Note: For the following steps, the supplied pipe; Attach the main regulator hose assembly to the

Fig 17 Fig 18 Fig 19 Installing the L.P. regulator 28. Remove the NG regulator from the main gas pipe using an adjustable wrench. The NGregulator is located on bottom of grillhead (Fig. 17). Note: For the following steps, the supplied pipe dope needs to be applied to all fittingsbefore the fittings ...

Page 8 - Converting the Rear Infrared Burner to LP

Fig 20 Fig 21 Fig 22 Fig 23 Fig 24 Rear Screws Converting the Rear Infrared Burner to LP 31. Remove the four screws on the inside of the grill that hold the rear infrared cover in place (Fig. 20). 32. Close the grill hood slowly. 33. Remove the two screws from the back infrared cover, located on the...

Page 9 - Label the Grill; Note: At the completion of the; All codes must be followed.

Label the Grill 44. Apply conversion label 9992-462 on the grill, next to the lighting instruction label (Fig. 25). Label Your Grill Note: At the completion of the conversion, a leak test should be performed on all fittings. See Use and Care manual for leak testing procedure. Installation is now com...

Page 10 - NOTES

__________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________ __________________________________________...

Coleman 9992-449 - Manuals

Manuals:

Manual Coleman 9992-449

Summary

Coleman Manuals