Clifford XL4000 - Manuals

Standard Features of the XL4000 (cont.) ✔ High-Luminescence LED Status Indicator with Automatic Battery-Saving Mode — Adds visual deterrence and identifies system status. To conserve vehicle battery power, if the system has remained continuously armed for48 hours, the flash rate will automatically s...

Your 4-button/12-channel remote controls The 4-button/12-channel remote controls are ultra-sophisticated miniature radiotransmitters powered by a tiny 12-volt battery. Range is up to 100 feet. A weak remotecontrol battery will reduce range. Electrical interference and even sunspots can interruptthe ...

TO ACTIVATETHE PANIC FEATURE . . . . . . . . . . Press button 1 (channel 1) for 3 seconds. The parking lights willflash repeatedly and the siren will blare for 30 or 60 seconds(user-selectable), or until you press button 1 again to turn it off. Ifthe ignition is on (indicating you are in the car), t...

Anti-CodeGrabbing™ (ACG) with Random Code Encryption A Clifford exclusive that protects you and your automobile from the most effective andonerous car stealing device ever used by car thieves — a code-grabber. Code-grabbersare far more effective and efficient than scanning. Unlike scanners that sequ...

UltraSecure™ Coded Valet Mode Your secret valet code In seconds, thieves can disable all other alarm brands by hotwiring the ignition andflicking an easy to find “hidden” valet switch. Your system has safeguards that absolutelyensure a thief cannot enable the valet mode as a way of “turning off” you...

To exit valet mode 1. Turn the ignition switch to its “ON” position or start the engine.2. Flick the switch back to its center position. The LED will turn off to confirm that the system is now in its normal operating mode. Setting your own secret valet code Since all XL Series systems have the same ...

FACT™— False Alarm Control and Test With FACT, you’ll never experience repeated false alarms. If the Insignia Siren goes off,DO NOT remotely disarm the system; allow it to run for the full siren duration. Beforesounding the siren a second time, the system automatically checks for another activatedtr...

Remote controlled sensor adjustments Due to ever-changing conditions, all alarms require periodic fine-tuning of their sensors.An improperly adjusted sensor is the most common cause of false alarms. With otheralarms, this requires repeated trips back to the dealer. Not so with XL4000. You canadjust ...

1. Remotely disarm, then turn on the ignition. The LED status indicator inside your vehicle will blink 1-3 times, pause, then repeat. 2. Count the number of blinks in one cycle between pauses (for your convenience, the blink cycle repeats a total of 5 times) and refer to the chart below: Number of L...

Long-term chirp silencing: Whenever you wish, you may silence your XL4000’s arm and disarm chirps until you decide to restore them. The parking light flasheswill continue to provide visual confirmation of remote controlled arming anddisarming. See User-selectable features on pages 20-24. Remote cont...

User-selectable features Your XL4000 allows you to set many of its features to your own personal preferences.Although the system’s programming capabilities are very extensive, we have made theprogramming procedures very simple: to make a change, you just flick the PlainViewswitch a few times. Once y...

EXAMPLE 1: Turn on AutoArm & Lock: You can set the system to automatically lock the car doors when the system AutoArms(see page 21). To turn on the AutoArm & Lock feature, you’ll note that “AutoArm &Lock” is in column 3, row 2 of the Table (on pages 23-24). The “off” in bold typeindicate...

Table of user-selectable features: 1 chirp = OFF, two chirps = ON. Feature Select Column 1 1st latched Column 2 2nd latched Column 3 3rd latched Row 1 1st momentary Add new remote to channel 1 info on page 11 NOTE 1 AutoLock on/off info on page 16 Enhanced AutoArming: on/off info on page 13 Row 2 2n...