Clifford Model RSX1.5 - Manuals

1 10 0 © 2005 Directed Electronics—all rights reserved Icon Not applicable. Icon The siren icon will display when a security feature has been trig- gered. Icon The siren icon will display when a security feature has been trig- gered. This icon will remain displayed until the system’s page is cleared...

1 11 1 © 2005 Directed Electronics—all rights reserved Icon Not applicable. Icon Not applicable. Icon The ignition icon will display if the ignition is turned on when the system (doors) are locked. Icon Not applicable. Number Icons When either of the channel 2 or 4 outputs is activated the appro- pr...

1 12 2 © 2005 Directed Electronics—all rights reserved A page is the signal the 542 control module sends to the remote control as confirmation of receipt of a command. When the remote control receives a page it will generate a page notification to the user (notifications are audible beeps or remote ...

1 13 3 © 2005 Directed Electronics—all rights reserved To enter programming mode Press and hold all four remote control buttons simultaneously until one long beep is heard. Programming Mode has now been entered. Page Notification The remote control can be programmed to notify the user of a page by a...

1 14 4 © 2005 Directed Electronics—all rights reserved Illumination On/Off Within five seconds of entering Programming Mode, press . The remote will beep once for on, twice for off and the light will turn on/off with each press. Page Mode On/Off After entering Programming Mode, press within five sec...

1 17 7 © 2005 Directed Electronics—all rights reserved Y YO OU U M MU USSTT IIM MM MEED DIIA ATTEELLY Y CCEEA ASSEE TTH HEE U USSEE O OFF TTH HEE U UN NIITT A AN ND D SSEEEEK K TTH HEE A ASSSSIISSTTA AN NCCEE O OFF A AN N A AU UTTH HO OR RIIZZEED D D DIIR REECCTTEED D EELLEECC-- TTR RO ON NIICCSS D ...

1 18 8 © 2005 Directed Electronics—all rights reserved If Passive Mode has been programmed on, then it is also possible to program the system for Passive Locking. With Passive Locking, the vehicle doors lock automatically at the same time that the Failsafe ® Starter Kill is activated. If Passive Loc...

2 20 0 © 2005 Directed Electronics—all rights reserved TTo o een ntteerr o orr eexxiitt V Vaalleett M Mo od dee:: 1. Turn the ignition on. 2. Turn the ignition off. 3. Press and release the Valet switch within 10 seconds. The status LED will light steadily if you are entering Valet Mode and will tur...

2 21 1 © 2005 Directed Electronics—all rights reserved This feature allows you to remotely start and run your vehicle for a programmable period of time. This makes it possible to warm up the engine, as well as adjust the interior temperature of the vehi- cle with the climate control system. If inter...

2 22 2 © 2005 Directed Electronics—all rights reserved W Wh heen n yyo ou u aarree rreeaad dyy tto o d drriivvee tth hee vveeh hiiccllee:: 1. Insert the ignition key and turn it to the ON (not the START) position. 2. Press the brake pedal. N NO OTTEE:: If the brake pedal is pressed before the key is...

2 23 3 © 2005 Directed Electronics—all rights reserved To turn the rear defogger output ON: 1. Simultaneously press & release the + + buttons on the remote control. 2. The lights will flash 3 times. 3. The rear defogger output will once again activate when the vehicle is remote started. N NO OTT...

2 28 8 © 2005 Directed Electronics—all rights reserved ■ Passive Locking or A Accttiivvee LLo occkkiin ng g (doors lock only with the transmitter). With Passive Locking, the vehicle doors lock automatically 30 seconds after the ignition has been turned off. Passive Locking can only be selected when ...

3 31 1 © 2005 Directed Electronics—all rights reserved N No otteess