Clifford GP500 - Manuals

TO RE MOTELY BY PASS BOTH ZONES: During the first 10 seconds after arming the system remotely, simultaneously press buttons II and III on the remote control and hold for three seconds. The system provides four indicator light flashes to indicate when the warning zone is bypassed, and another four in...

TO RE MOTELY BY PASS THE WARN ING ZONE: During the first 10 seconds after arming the system remotely, press button III on the remote control. The system provides f our indicator light flashes when the warning level is bypassed. TO RE MOTELY BY PASS BOTH ZONES: During the first 10 seconds after armin...

False Alarm Pre ven tion & FACT™ With Clifford’s patented FACT (False Alarm Control and Test) feature, you’ll never experience repeated false alarms. If the siren sounds, DO NOT remotely disarm the system; allow it to run for the full 30-second siren duration. Before sounding the siren a second ...

How to in ter pret the LED status in di ca tor LED Condition Meaning Off Sys tem is dis armed Flashing Steadily (Ignition off) Sys tem is armed Flashing rapidly (ignition off) AutoArming Count down Flashing slowly (ignition on or off) Sys tem is dis armed but Im mo bi li sa tion points are en gaged ...

Smart Au toTest ing™ Each time you remotely arm the system, it tests all triggers and sensors. For example, if the Helmet Theft Prevention System is active, you will receive the usual 2 chirps and flashes , then, 5 seconds later , there will be 4 chirps and 4 flashes . If a sensor is malfunctioning,...

LED flashes Meaning 1 flash Ig ni tion switch was turned on 2 flashes Ac ti va tion of Digi tal Tilt/Mo tion Sen sor 3 flashes Ac ti va tion of Dual- Level Piezo Sen sor 4 flashes Ac ti va tion of hel met theft pre ven tion de vice 5 flashes Op tional ad di tional trig ger was ac ti vated (such as a...

Smart prior in tru sion at tempt alert If you hear three chirps when you remotely disarm, it means that a trigger or sensor was activated in your absence. When you turn on the ignition (or start the engine), the LED will flash 1-8 times, pause, then repeat the flash cycle 4 more times. Count the num...

Smart Powe rUp™ 2 If power to the system is ever removed, SmartPowerUp 2 ensures that your GP500 system automatically restores itself to its previous state when power is restored. So if a thief disconnects the power and then restores it in an attempt to start the motorcycle, the system will re-arm a...

2. Within 5 seconds, press and release the PlainView 2 ✱ button 7 times. To help you count, you will hear a chirp each time you press the ✱ button. After 7 presses, wait for a single chirp, then immediately enter your new PIN code. Example: To enter 4301 as your new code, you would press the switch ...

Step- by- step pro gram ming in struc tions 1. Refer to the Table of programmable features on page 32 and find the feature you wish to program. Make note of the number of times to press the ✱ button. 2. Turn the ignition on, or start the engine (skip this step if the engine is running). 3. Enter you...

Ta ble of Pro gram ma ble Fea tures Feature Factory Setting No. of times to press the ✱ button Sec- ondary Action Program completion confirm- ation Additional Action AutoArming OFF 2 - 1 chirp=OFF2 chirps=ON - Chirps ON 3 - 1 chirp=ON2 chirps=OFF - FACT ON 4 - 1 chirp=OFF2 chirps=ON - Change PIN cod...

Your serial number is: REGISTER ONLINE: Within 10 days of purchase, you m a y r e g i s t e r y o u r C l i f f o r d p u r c h a s e o n l i n e a t www.clifford.com/manuals so that we can contact you in the future if there are any changes or improvements to your GP500 system. Or just photocopy thi...