Clifford AvantGuard II - Manuals

How to Arm the System with the Remote Control 1. Press remote control button I/channel 1.2. Simultaneously, several actions will take place to confirm remote disarming: • The siren will chirp twice providing audible confirmation from a distance. (Ifyou prefer, you can turn off the chirp acknowledgem...

Valet Mode Whenever your vehicle is to be serviced, washed or valet parked, you must use thevalet mode to disarm the system and override its Smart AutoArming feature. How to Enable Valet Mode 1. Insert your key and turn the ignition to the “ON” position.2. Flip the valet/program switch to its latche...

Smart AutoArming™ If you forget to arm your system with the remote control, it will arm itself automat-ically 30 seconds after the vehicle doors are closed. (The Multicolor LED will blinkgreen for visual confirmation of the 30-second Smart AutoArming countdown). If youre-open any door(s) within the ...

Prior Intrusion Attempt Alert If the alarm sounded while you were away, when you remotely disarm the systemwill issue three chirps and three flashes of the parking lights. You’ll note that theMulticolor LED will blink in red 1-7 times, pause for one second then repeat thecycle four more time. Count ...

b. To turn the chirps on: Flick the switch to its latched position, then back to center. c. You will hear 3 chirps to confirm chirp muting or restoration.7. Turn the ignition off. You will hear 3 chirps to confirm exiting of program mode. One-Cycle Chirp Muting: This is particularly useful when park...

Remote Engine Starting How to Remotely Start the Engine Remote control button II (channel 2) will remotely start (or shut down) the engine:1. With the remote control microswitch in the up position, press and hold button II (channel 2) until you see your vehicle’s parking lights flash twice. (NOTE: A...

How to Engage AutoStart 1. Make sure that the gas tank is at least half full. To conserve battery power, make sure the air conditioner, radio and all other accessories are turned off. 2. Insert your ignition key and turn the switch to the “ON” position.3. Within 10 seconds, press and hold the valet/...

How to Program Your AvantGuard II NOTE: A Quick Programming Guide is on pages 17-19. However, if you areprogramming the system for the first time, we strongly recommend that youfollow the detailed instructions in the specific sections that follow beforeattempting to use the guide. F or your convenie...

How to Set Your Own Personalized Siren Sound You can program a unique code of siren chirps to recognize your system at a distance..Your Personalized Siren Sound will consist of any combination of eight or less dot(short) and/or dash (long) siren pulsating sounds. A dot is a 1/4-second siren chirp.A ...

How to Set the Smart AutoArming Entry Delay Entry delay is programmable from 1 to 59 seconds (factory preset to 15 seconds). Forsecurity reasons, the entry delay should be just enough time for you to open the doorand turn on the ignition. To set a new entry delay, use the following procedure:1. Turn...

b. Flip the switch to its latched position, then back to center. You will hear 3 chirps. c. Tap the switch to its momentary position 1 time.d. Flip the switch to its latched position, then back to center. You will hear 1 chirp. e. Flip the switch to its latched position, then press button II on your...

Quick Programming Guide Once you are familiar with the AvantGuard II programming procedures, you mayuse this quick guide to make programming changes. IMPORTANT: DO NOT use this guide unless you have programmed theAvantGuard II before. If you have never programmed the system before,you should refer f...

ProgrammableFeature Parameter Action Step Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PersonalizedSiren Sound Any patternof up to 8 dotsand/or dashes Flick switch to M M L C M M M L C Number of chirps 2 3 3 3 Special instructions 2 Siren duration From 1 secondto 5 minutes Flick switch to M M L C M M L C...

ProgrammableFeature Parameter Action Step Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 AutoLock andAutoUnLock Enable Flick switch to M L C M M L C L C Number of chirps 1 2 3 Disable Flick switch to M L C M M L C M Number of chirps 1 2 3 AutoStart Enable Flick switch to M L C M L C M C Number of chirps 1 ...