Clarion S100 - Manuals

4 system maintenance The system requires no specific maintenance. Your remote control is powered by a small, lightweight 3 volt lithium battery that will last approximately one year under normal use. When the battery weakens, operating range will be reduced and the LED on the remote will dim. fcc/id...

6 using your system The buttons used in the instructions in this manual correspond to the standard configuration. Remember, this is not the only way your remote may be set up. It can be custom configured to meet your needs. active arming You can activate, or arm, the system by pressing on your remot...

7 vides you with a 10-second warning prior to arming. When armed, your vehicle is protected as follows: ➤ Light impacts will trigger a warning signal. When triggered, the siren will chirp and the parking lights will flash for a few seconds. ➤ Heavy impacts will trigger the system. The triggered sequ...

8 remote sensor bypass Remote Sensor Bypass allows you to select which of the security sys- tem's inputs or sensors will be active and which will be bypassed at the time that the system is armed. (See the Table of Zones section of this guide.) Pressing again within five seconds of arming the securit...

10 diately. The six second timer is provided for your convenience, in casethe system is accidentally triggered. disarming without a remote This feature allows you to disarm the security system without theremote should it be lost, damaged, or disabled. In order to disarm thesystem without a remote, y...

12 override mode You can prevent your security system from automatically arming and triggering by using Override Mode. This is very useful when washing the vehicle or having it serviced. In Override Mode, the security system will not arm, even with the remote remote, but all convenience functions (d...

13 false alarm prevention circuitry Your system has false alarm prevention circuity. It prevents annoying repetitive trigger sequences due to faulty door pin switches or environ- mental conditions such as thunder, jackhammers, airport noise, etc. Example If the alarm triggers three times within a 60...

14 diagnostics The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it. It detects any faulty switches and sensors and prevents them from dis- abling the entire system. The microprocessor will also record and report an...

15 of Zones section of this guide.) The system will retain this information in its memory, and continue to chirp four or five times each time it is disarmed, until the next time the ignition key is turned on. system status chirps The siren will chirp when arming/disarming the system. The pattern of ...

16 table of zones The zone number is the number of LED flashes used by the system to identify that input. The standard input assignments are listed below, along with spaces to write in any optional sensors or switches you have had installed. interpreting zone diagnostics Warn Away responses are not ...

17 anti-code grabbing The receiver and remotes each use mathematical formulas called algo- rithms to change their codes each time the remote is used. This technol- ogy has been developed to increase the security of the unit. The control unit knows what the next codes should be. This helps to keep th...

18 individual remote recognition Individual remote recognition is a feature available. Using the Pro Security Programmer, a hand-held programming tool, your dealer can program many of the system settings. The programmer makes it possi- ble to program different settings for each remote that is used w...

19 power saving mode Your system will automatically enter a power saving mode while armed or in valet mode, after a period of time in which no operation has been performed. This lowers the current draw to the vehicle’s battery. Power Saver mode takes over under the following conditions: ➤ Power savi...

20 programming options Programming options control what your system does during normal operation, and require few or no additional parts. However, some may require additional installation labor. The following is a list of the program settings, with the factory settings in Bold : ➤ Active arming (onl...

23 of six different tones in sequence. Any of these tones can be eliminated by your dealer, resulting in a unique, easily identi- fiable siren sound. The siren chirps can be either full volume or six decibels quieter than the full alarm blast. installation options The system has many options that ma...

24 anti-carjacking system The optional anti-carjacking system feature is designed to ensure that any unauthorized user of your vehicle (even if using your keys and remote control) will not be able to permanently separate you from your vehicle. This system cannot prevent a carjacking attempt; however...

25 it will initiate its triggered sequence (see below) if any door is opened and closed. If you are forced from the vehicle, the system will trigger as the door is opened and closed. This is how the system works to com- bat intersection carjacking. To protect against parking lot carjacking, arm the ...

26 until the system is disarmed. If the door is opened or the ignition is turned off and on in an attempt to restart the car, the siren and light flashing will begin again. disarming the anti-carjacking system Take the time to familiarize yourself with the anti-carjacking triggering sequence and the...

27 glossary of terms Control Unit: The "brain" of your system. Usually hidden under the dash area of the vehicle. It houses the microprocessor which monitors your vehicle and controls all of the system's functions. Starter Kill: An automatic switch controlled by the security system which pre...

29 security & convenience expansions Here we have listed only some of the many expansion options avail- able. Please contact your dealer for a complete explanation of all the options available to you. Audio Sensor: Metal on glass, glass cracking, and breaking glass each produce distinctive acous...

31 QUICK REFERENCE GUIDE To arm using your remote ➤ You can activate, or arm, the system by pressing on your remote for one second. When the system arms, you will hear a short siren sound, or chirp, andthe parking lights will flash once. If the vehicle’s power door locks have beenconnected to the sy...