Clarion APX200.2 - Manuals - manualsarea.com

Page 2 - save your original sales receipt as proof of; TABLE OF CONTENTS

INTRODUCTION The Clarion APX200.2 and APX400.2 are full-featured two-channel amplifiers.incorporating the following features: • Full frequency response with low distrotion and exceptional signal to noise performance • Advanced circuit design that features bridgeable and mixed mode operation for use ...

Page 3 - Speaker Level Inputs

DESCRIPTION The Clarion APX200.2 and APX400.2 two-channel amplifiers provide 2x70watts and 2x110 watts of power into a 4 ohm load and 2x110 watts and 2x190watts of power into a 2 ohm load. These full featured models are an excellentchoice for a variety of car audio sound system configurations. The A...

Page 4 - Gain Control; - This allows you to set the nominal operating level of the; Bass Boost Control; - The crossover frequency is fully; Crossover Frequency Multiplier Switch; - This switch is equipped with a 12dB per octave; Input Mode Switch; - This switch allows you to set the input mode. Stereo; Speaker Level Inputs; - These provide connections for a high-level stereo

• Gain Control - This allows you to set the nominal operating level of the amplifier. The amplifier ’s range, 250mV to 2.5V for RCA inputs or 500mV to5V for speaker level inputs, can accommodate input levels from virtually anybrand of source unit. • Bass Boost Control - The amplifier also features a...

Page 5 - CONNECTIONS FOR POWER AND SPEAKERS

CONNECTIONS FOR POWER AND SPEAKERS The rear panel of the APX200.2 and APX400.2 both contain power and speakerconnections as shown below. 5 1. Left Speaker Output2. Right Speaker Output3. Remote Turn-on Input 4. Ground Input5. Battery + 12v Input6. 25 Amp Fuse / 40 Amp Fuse Figure 2-

Page 6 - APPLICATIONS; Bridged- Mono Subwoofer System; Figure 3; Set X-Over Mode to LP and adjust

APPLICATIONS The Clarion APX200.2 and APX400.2 2-channel car audio amplifiers can beused in a variety of system applications. Here are some examples to help planyour own installation. Bridged- Mono Subwoofer System 6 Figure 3 - In this application the amplifier is bridged for mono operation to drive...

Page 7 - Figure 4; - In this application, the amplifier is used in stereo and drives two

2-Channel Full-Range, Satellite, or Subwoofer Stereo System (Set INPUT SELECT Switch to STEREO) 7 Set X-Over Mode as shown. Set X-Over Mode as shown; adjust FREQ to speaker specifications. Set X-Over Mode as shown; adjust FREQ to speaker specifications. Figure 4 - In this application, the amplifier ...

Page 8 - Mixed-Mode Satellite and Subwoofer System; The amplifier can be configured for a mixed-mode operation. The

Mixed-Mode Satellite and Subwoofer System (Set INPUT SELECT Switch to STEREO) 8 Set X-Over Mode to OFF. FREQ (hz) 80 100125150200 L (mH) 8.06.45.14.23.2 C (uF) 497398318265199 NOTE: Chart values based on 4 ohm speakers. Figure 5 - The amplifier can be configured for a mixed-mode operation. The table...

Page 10 - Never ground the speakers to the vehicle chassis or body.

4. A secure clean ground connection is critical to the performance of yourClarion amplifier. Use the shortest ground wire possible snd securely connectto the car chassis to minimize resistance and avoid noise problems. 5. Add an external fuse on the amplifier ’s positive (+) power lead and connectit...

Page 11 - Electrical connections for the APX200.2 or the APX400.2

11 Figure 6. - Electrical connections for the APX200.2 or the APX400.2

Page 15 - NOTES