Clarion 310C - Manuals

Clarion AutoPC Owner’s Manual 3 DCP release - Press to remove control panel. Start Key - Display start menu (main menu). α α -Selector - Navigate programs and options with a single finger. MENU - Press to get to extra options that are available with some programs. MUTE – Press to silence audio. HELP...

Clarion AutoPC Owner’s Manual 4 First, become familiar with the Controls and General Operation of theClarion AutoPC system as described in this chapter. Second, spend 10 minutes previewing this Owner’s Manual: • Scan the Table of Contents, it shows you the breadth of information on your Auto PC. • G...

Clarion AutoPC Owner’s Manual 5 The α -Selector enables you to navigate through various Auto PC functions with a single finger. This is how you do it: 1. Put your index finger on the raised center element (has awhite dot) of the α -selector as shown in the figure. CAUTION! DO NOT TAKE YOUR EYESOFF T...

Clarion AutoPC Owner’s Manual 6 Detachable Control Panel (DCP) The control panel (Detachable Control Panel) can be detached to preventtheft. After detaching the control panel, store it in the protective caseprovided. We recommend taking it with you when leaving the vehicle. 1. Turn the power off. 2....

Clarion AutoPC Owner’s Manual 7 You can also detach the DCP in its lowered position. The procedure is asfollows: 1. Turn power off. 2. Lower the DCP to its fully open position 3. With your left index finger, find the release button as shown inthe drawing. Push upward onthe release button, and pull t...

Clarion AutoPC Owner’s Manual 8 The DCP has three lowered positions, each of which is reinforced by aclicking sound: • 60 degrees (partially open) • 45 degrees • 30 degrees (fully lowered) Warnings! 1. The DCP can easily be damaged by shock. After removing it, be careful not to drop it or subject it...

Clarion AutoPC Owner’s Manual 9 1. Be sure that the DCP holder is fully closed before attaching theDCP. 2. Examine the back of the DCP and notice that there is alocking hook on the back of theDCP and that the hook must gointo the receptacle on theholder. 3. Slide the locking hook on the back of the ...

Clarion AutoPC Owner’s Manual 10 General Operations 1. Press the POWER button 2. The display lights up immediately. The Auto PC remembers its last operation mode and will automatically switch to display that mode. 3. To turn off the power to the unit, press the POWER button. NOTE: Use caution while ...

Clarion AutoPC Owner’s Manual 11 NOTE: Be sure to reduce the volume level before shutting off the ignition key or turning the unit’s power off. The unit remembers the last volumesetting before power was turned off, and it will start with that same settingwhen power is turned back on. The volume cont...

Clarion AutoPC Owner’s Manual 12 1. Turn power off. 2. Turn the vehicle ignition off. 3. Remove the Detachable Control Panel (see Removing the DCP) 4. Lower the DCP holder as shown in the picture. Removethe battery holder by placing thetip of the flathead screwdriveron the exposed edge andpulling th...

Clarion AutoPC Owner’s Manual 13 5. Place CR2032 Coin Cell Battery with plus (+) side up in thebattery holder as shown. 6. Install the battery by pushing the holder into the unit asshown. Return the DCP holderto the fully closed position (thevertical position).

Clarion AutoPC Owner’s Manual 14 For information on … See … Speech commands Using Speech Commands chapter orquick reference material. Auto PC screens and keys Getting Ready chapter. To … Do this … See Help Tips for the current program screen Press the HELP key on the DCP. Hear which speech commands ...

Clarion AutoPC Owner’s Manual 15 Chapter 2 – Using Speech Commands Auto PC can understand words and short phrases spoken as commands,called “speech commands.” Using voice commands while driving allowsyou to operate the system without distracting your attention away from theroad or removing your hand...

Clarion AutoPC Owner’s Manual 16 The Auto PC has been optimized to recognize adult speakers. Use thefollowing guidelines when giving commands to Auto PC: 1. Remember to wake up Auto PC. 2. Say each command clearly and distinctly, but don’t shout. 3. Wait for the “heard” tone before saying another co...

Clarion AutoPC Owner’s Manual 17 Getting help with speech commands While in the Start menu you can press HELP to get assistance withspeech commands. You will see voice commands and how Auto PCresponds with musical tones. Auto PC tells you it is “listening” to you witha specific tone, and that it has...

Clarion AutoPC Owner’s Manual 18 If, after saying “Auto PC” you do not hear the “listening tone,” consult theTips and Troubleshooting chapter of this manual. Auto PC has three tones that help you give speech commands: 1. When you wake up Auto PC, you’ll hear the awake tone, and see a green speech co...

Clarion AutoPC Owner’s Manual 19 Chapter 3 - Getting Ready Before you start using your Clarion AutoPC system, take a few minutes tobecome familiar with the unit. Your Auto PC gives you information in two ways: 1. By displaying information on the screen. 2. Through voice synthesis, Auto PC reads stat...

Clarion AutoPC Owner’s Manual 20 Display layout When you say “Auto PC” or use PTT, Auto PC “listens” for speechcommands and a green bar appears across the bottom of the display.The green bar gradually disappears as the listening timeout expires. CAUTION! ONLY LOOK AT THE AUTO PC WHEN IT IS SAFE ANDO...

Clarion AutoPC Owner’s Manual 21 NOTE: Neither the green bar nor the blue bar is displayed if the listening timeout is set to Always (see the Customizing your Auto PC chapter). If you press and hold the PTT key, Auto PC continues listening until yourelease the key. Using Speech to go to a program Yo...

Clarion AutoPC Owner’s Manual 22 To Say You’ll hear Wake up Auto PCspeech recognition Auto PC and current program name . You can eliminate current program name feedback. See Customizing Your Auto PC,Speech feedback. Go to CD Playerprogram CD Player (speech command heard) Using keys to go to a progra...

Clarion AutoPC Owner’s Manual 23 To Press You’ll see Display the Start menu The Start menu Select (highlight) aprogram icon in theStart menu or The Start menu cyclesthrough the program icons Go to the selectedprogram (enter) or Hold The program’s main screen Go directly to a programwith the program’...

Clarion AutoPC Owner’s Manual 24 Navigating within programs You can navigate within a program by pressing the MENU key on theDCP. For example, under Radio you may change the Audio Settings: Radio icon This is the first oftwo radio options Press (enter) to gointo Audio Settings Press (up or down) to ...

Clarion AutoPC Owner’s Manual 26 The procedures shown here will get you started using your Auto PC.These are just some of the settings that you can adjust. (See“Customizing Your Auto PC” later in this manual.) Clock, date, time, and regional setup Do clock, date, time, and regional setup by completi...

Clarion AutoPC Owner’s Manual 27 Manual ! ! Comment Press to select Set Date , and press Select and enter Set Date. Press to change the Month--press to move to next edit box Set the Month, Day and Year. When the date is set, press BACK Return to Set Date screen. Manual ! ! Press to select Set Time a...

Clarion AutoPC Owner’s Manual 28 Manual ! ! Press to select Regional Setup , and press Select and enter RegionalSetup. Change the Regional styles and formats as shown in the table below: To change this… Press to highlight And then press Currency Currency Date style Date style Distance Distance Time ...

Clarion AutoPC Owner’s Manual 29 Using Global Speech Commands Global speech commands are available all the time, in any program.Global commands include speech commands that take you right to manyof the programs on your Auto PC, plus commands that are useful in anyprogram, such as “Read” and “What ti...

Clarion AutoPC Owner’s Manual 30 Voice Comments Auto PC ... To wake up Auto PC, if necessary. What time is it? … Auto PC reads the time aloud. For informationon setting the clock, see the section earlier in thischapter. Audio volume can be adjusted by manual controls on the DCP of the AutoPC or by u...

Clarion AutoPC Owner’s Manual 31 Using Program Speech Commands Unlike global speech commands, program commands are specific to aparticular program – you can only use them when you are in thatprogram. The following sections show you some examples of what you canaccomplish using program commands. • Go...

Clarion AutoPC Owner’s Manual 32 Requires you to have: • Set a radio station preset. For more information, see “Setting your own Preset stations” in the chapters, “Using the Radio, and AudioAdjustments.” • Recorded a name (for example, “Classical”) for the preset. For more information on recording a...

Clarion AutoPC Owner’s Manual 33 Requires you to have inserted an audio CD. For more information, see the chapter, "Using the CD Player." Voice Comment Auto PC ... CD Player ... Auto PC goes to the CD playerprogram and starts playing the CD. Next … Auto PC goes to the next track onthe CD. To...

Clarion AutoPC Owner’s Manual 35 Chapter 4 – Using the Radio The fastest way to learn the Clarion AutoPC system is to try out thefunctions you will frequently use. Once you have learned how to set upand use commands for your radio, everything else is similar and thereforeeasy. The Radio program in A...

Clarion AutoPC Owner’s Manual 36 Using the DCP keys ( ) you can seek to a station, using ( ) you can fine-tune to a station. Also, you can enter a station number directly withthe numeric keys (0 – 9) after pressing (#). By pressing MENU you canalso go to the Radio options, where you can edit the lab...

Clarion AutoPC Owner’s Manual 37 You can establish up to 10 Preset stations for AM and up to 10 Presetstations for FM. You can also use your voice to “train” Auto PC to recognize custom voicecommands for your Preset stations. If, for example, you have a favoriteROCK and CLASSICAL station, you could ...

Clarion AutoPC Owner’s Manual 38 Note that the Display now reads “ Preset 1 ” in the lower right of the display. Use the same procedure to set other Preset stations: • Preset 1, 2, . . . , 9, 0 for AM • Preset 1, 2, . . . , 9, 0 for FM Voice Manual ! ! Comment Auto PC ...Radio ... Press Start , then...

Clarion AutoPC Owner’s Manual 39 You can assign station names for your Preset stations using names ofyour choice. This next sequence builds upon the Preset 1 station alreadyestablished in the earlier example (ROCK = Preset 1 = 94.7 FM). Manual ! ! Press Start , then to highlight Radio and then Press...

Clarion AutoPC Owner’s Manual 40 Manual ! ! Press Start , then to highlight Radio and then Press MENU then to select Edit Preset Stations Press for display to read “<Enter Station Name>” then press Press to enter the letter “ R ” then to move to the next spaces and enter “ O ” then “ C ” then ...

Clarion AutoPC Owner’s Manual 41 Use the following procedure to adjust audio settings from the Radioprogram. Manual ! ! Press Start , then to highlight Radio and then Press MENU Press to select Audio Settings ; for more information, see Audio Adjustments chapter Changing Radio Options

Clarion AutoPC Owner’s Manual 43 Chapter 5 – Using the CD Player The Auto PC CD Player program gives you access to advanced playfunctions using speech commands. Using speech commands, you can: • Play and pause the CD • Delete the current track from the tracks played for the current CD • Play tracks ...

Clarion AutoPC Owner’s Manual 44 Types of CDs you can use with Auto PC CD type Comments Normal consumerAudio CDs These are the popular compact discs used toplay music. 2 ½ inch consumerCD Singles These CDs can also be used in the Auto PC’sin-dash player. 4 ¾ inch computerCD-ROMs CD-ROMS are used by ...

Clarion AutoPC Owner’s Manual 45 1. Power on the unit and lower the control panel to allow insertionof a disc into the CD slot. Gripthe control panel, pulling thecontrol panel out outward anddownward in one continuousmotion as shown to the right. 2. Place the DCP in the fully open position as shown ...

Clarion AutoPC Owner’s Manual 46 (Before operating the CD Player, continued) 3. Look to see that the CD will clear the top of the controlpanel as illustrated on the right. 4. Push the disc into the CD slot half way, and the drive will pullit in the rest of the way. Correctclearance

Clarion AutoPC Owner’s Manual 47 Voice Manual ! ! (Stop your vehicle to domanual steps) Comments/Illustrations Auto PC …CD Player… Press Start , then to highlight CD Player , then To select the CD Playerprogram. Play ...Pause ... Play or pause a track. Note: Stop has the same effect as Pause . Next ...

Clarion AutoPC Owner’s Manual 48 Voice Manual ! ! Comments/Illustrations Delete ... Deletes track currently playing. Press MENU to highlight Disc Play List , then to see the Play List to choose the track, then to delete (orrestore) itPress BACK to see CD playback screen Manual ! ! Comments Press and...

Clarion AutoPC Owner’s Manual 49 Manual ! ! Comments/Illustrations Press MENU To see the CD Player options Press Select Display Press Select the display you want Use the following procedure to adjust audio settings from the CD Playerprogram. Manual ! ! Press MENU Press to select Audio Settings ; for...

Clarion AutoPC Owner’s Manual 50 1. Do not warp or bend a CD. 2. A CD is vulnerable to heat, so do not leave it near a heater, in the sun, or anywhere else where it will be exposed to heat. 3. Be careful not to scratch a CD. 4. Do not paste any labels on the disc surface or write anything on the lab...

Clarion AutoPC Owner’s Manual 51 Chapter 6 – Audio Adjustments You can change bass and treble, equalizer settings (including namedpresets), balance, fade, loudness, and volume presets. You can access Audio Settings through the Radio or CD Player programs, or from the Audio program in the Start menu....

Clarion AutoPC Owner’s Manual 52 (Making audio adjustments continued.) Manual ! ! Comments/Illustrations to select Eq and to select the preset you want to change Press then to change thesetting, to select another frequencyTo rename the Preset, press until Rename is shown Note: Rename is an optionals...

Clarion AutoPC Owner’s Manual 54 Here are illustrations of access to audio adjustments from either the Radio or CD Player programs. Voice Manual ! ! Comments/Illustrations Auto PC ...Radio ... Press Start , then to highlight Radio , then To select the Radioprogram. Menu Then Auto PC …CD Player… Pres...

Clarion AutoPC Owner’s Manual 55 Chapter 7 - Using Address Book With Auto PC’s Address Book, you can stay in touch with family, friends,and business contacts. Address Book stores work and home addresses,phone, fax and pager numbers, and e-mail addresses to give you quickaccess when and where you nee...

Clarion AutoPC Owner’s Manual 56 Address Book command words and keys This table lists some words and key presses used in Address Book. Voice Manual ! ! (Stop your vehicle to domanual steps) Comments Auto PC …Address book … Press Start , then to highlight Address Book , then To select the AddressBook...

Clarion AutoPC Owner’s Manual 57 The following examples illustrate commands to initiate dialing a numberfrom an existing Address Book entry. Actual dialing of the phone numberrequires a cell phone which is an optional accessory. Voice Manual ! ! Comments Auto PC …Address book … Press Start , then to...

Clarion AutoPC Owner’s Manual 59 The following examples illustrate recording and using a custom commandword to dial the phone. Manual ! ! Press Start , then to highlight Address Book , then to find the entry Menu and then to find Record Contact Name : Display reads “Say Command Word three times at t...

Clarion AutoPC Owner’s Manual 60 Voice Comments/Illustrations Auto PC …Address book … To select the Address Book program. Locate …<Marvin Adams> … This is displayed: And the unit “reads” the name “Marvin Adams.” Dial … The unit “asks” if you want to dial the number(example: Work phone is Prefe...

Clarion AutoPC Owner’s Manual 61 Add, edit or delete a contact These procedures help you to share contacts with other mobile devices,and make changes in Address Book. In the Getting Started chapter yousaw how to customize a radio station name. Adding a new entry to theAddress Book is similar as is s...

Clarion AutoPC Owner’s Manual 62 (Enter new name continued) Manual ! ! Comments when name is entered You are prompted to <Record Contact Name> Display reads “Say Command Word three times at the tone prompt.” Press if you want to skip recording the name.1. Record the new name three times when p...

Clarion AutoPC Owner’s Manual 63 Manual ! ! Comments Press Start , then to highlight Address Book , then To select the Address Book program. and , then To select a contact. Press MENU , then use to select Edit All Fields , then use to set Yes This procedure is required if you want toedit or add to a...

Clarion AutoPC Owner’s Manual 64 Phone 1. Work 2. Work2 3. Mobile 4. Car 5. Home 6. Home2 7. Pager 8. Assist Work 1. Work 2. Fax 3. Email 4. Title 5. Dept 6. Mobile 7. Pager 8. Car 9. Work2 10. Assist 11. Assist# 12. Spouse 13. Web 14. Bday 15. Anvrsry 16. Mr/Ms/.. 17. First 18. Middle 19. Last 20. ...

Clarion AutoPC Owner’s Manual 65 Manual ! ! Comments Press Start , then to highlight Address Book , then To select the Address Book program. and , then To select a contact. MENU , then to highlight Delete , then To delete a contact. to highlight Yes and press To confirm deletion. Be sure to checktha...

Clarion AutoPC Owner’s Manual 66 Transfer a contact If you have another mobile device powered by Windows CE, such as theHandheld PC or Palm-sized PC, you can quickly transfer your contacts toyour Auto PC through the infrared port. Manual ! ! Comments Press Start , then to highlight Address Book , th...

Clarion AutoPC Owner’s Manual 67 NOTE: If you are having trouble transferring data, be sure that your infrared ports are aligned. If the problem persists, change your infraredtransfer speed in Setup. (See “Customizing Your Auto PC.”) Browsing Contacts You can browse addresses using command words or ...

Clarion AutoPC Owner’s Manual 68 Voice Manual ! ! Comment Auto PC …Address book … To select the Address Bookprogram.To go to the next letter tab. Letter … "P" … To go to a specific letter tab.Example: the letter “P.” Next … or Previous … To scroll through contacts. Protecting Address Book in...

Clarion AutoPC Owner’s Manual 69 Chapter 8 - Using Directions Use the Auto PC’s driving directions to free yourself from struggling withmaps, and keep your attention focused on the road. The Directions feature is intended to provide turn by turn instructions toget you to a desired destination. Pleas...

Clarion AutoPC Owner’s Manual 70 With a map data CD, Auto PC can guide you to your destination. With Auto PC Directions, you enter a starting point and a destination.Directions calculates a route for you to take, and gives you turn-by-turndirections on screen and reads the directions to you. Maps us...

Clarion AutoPC Owner’s Manual 71 You will need a start point and a destination point to give to the Directionsprogram in order for it to calculate a route and supply you with specificdirections. Start and destination points come from a several sources.Two important sources are map data CDs and your ...

Clarion AutoPC Owner’s Manual 72 Directions command words and keys The following table summarizes the words and key presses used inDirections: Voice Manual ! ! (Stop your vehicle to do manual steps) Comment Auto PC …Directions … Press Start , then to highlight Directions , then To select the Directi...

Clarion AutoPC Owner’s Manual 73 Ways to select a start and destination points Types of locations Start Type Destination Type 1. Current GPS Location 1 Yes No 2. Last Destination Yes No 3. Street Address Yes 2 Yes 2 4. Point of Interest (POI) Yes 2 Yes 2 5. Intersection Yes 2 Yes 2 6. Address Book Y...

Clarion AutoPC Owner’s Manual 74 Commands to enter a start point Insert the appropriate map CD before using the procedures in thissection. Auto PC may request that you initialize navigation. Insert thenavigation initialization CD and follow the directions. Then insert the mapdata CD. Manual ! ! Comm...

Clarion AutoPC Owner’s Manual 75 When using the map data CD for the first time, the Directions program willrequest that you choose a state, e.g., Michigan, before requesting thatyou choose a city within the state. This initial condition is illustrated onlyonce in the pages which follow, in the descr...

Clarion AutoPC Owner’s Manual 76 (Entering Street Address as a start point continued) Manual ! ! Comment/Illustration Use or number keys to enter streetnumber, then Display (example) shows: for 5 seconds, then automati-cally shows Set Destination Manual ! ! Comment/Illustration Press Start , then to...

Clarion AutoPC Owner’s Manual 77 (Entering Point of Interest as a start point continued) Manual ! ! Comment/Illustration Use and to highlight the city of your choice, then Display shows the first of manytypes of Points of Interest.Example: Airport. Use to highlight the Start POI Type,then Display sh...

Clarion AutoPC Owner’s Manual 78 (Entering Intersection as a start point continued) Manual ! ! Comment/Illustration Use and to highlight the Start Street of your choice, then Use to highlight the Cross Streetof your choice, then Display shows confirmation ofStart Point for 5 seconds, thenautomatical...

Clarion AutoPC Owner’s Manual 80 You can transfer an address entry from a Windows CE-based mobiledevice using the infrared port. On your mobile device, you send theaddress via the infrared port as illustrated below. Manual ! ! Comment/Illustration Press Start , then to highlight Directions , then Se...

Clarion AutoPC Owner’s Manual 82 Commands to enter a destination point Manual ! ! Comment/Illustration Selection of start point alreadysuccessfully completed Display shows: Press to select Set Destination Type,then use to highlight Street Address , then Display (example) shows: Use and to highlight ...

Clarion AutoPC Owner’s Manual 87 Calculating the route When you request a route, Auto PC takes the starting point anddestination you’ve entered and determines a route for you to take. The Directions navigation system is only an aid. Make your drivingdecisions based on your observations of local cond...

Clarion AutoPC Owner’s Manual 88 You have a choice of a route that includes or excludes freeways. Youalso have the option to have Auto PC display safety warnings. Manual ! ! Comment/Illustration Destination point has already beenselected and confirmed Display shows: Press MENU to see Set Route Prefe...

Clarion AutoPC Owner’s Manual 89 Manual ! ! Comment/Illustration Destination point hasalready been selectedand confirmed Display shows: Press 3 key or Display shows: Depending on the distance traveled and thecomplexity of the route, this calculation maytake up to several minutes.When the calculation...

Clarion AutoPC Owner’s Manual 90 Driving the route Do not follow the route suggestions if you are instructed to perform anunsafe or illegal maneuver, if you are placed in an unsafe situation, or ifyou are directed into an area which you consider unsafe. The driver isultimately responsible for the sa...

Clarion AutoPC Owner’s Manual 91 Voice Manual ! ! Comment Auto PC …Directions … Press Start , then to highlight Directions , then Select Directions program. Press MENU , then use to highlight Backtrack , then Select Backtrack and Displayshows: When the calculation is donethe display shows (example):...

Clarion AutoPC Owner’s Manual 93 Chapter 9 - Using Messages With the Auto PC Messages program and the optional wireless receiverhardware, you can receive and listen to messages over the airwaves. Messages lets you know when you’ve received important information, andreads it to you. The information a...

Clarion AutoPC Owner’s Manual 94 Messages command words and keys The following table shows the words and key presses used in Messages. Voice Manual ! ! (Stop your vehicle to do manual steps) Comment Auto PC …Messages … Press Start , then to highlight Messages , then Highlight and selectMessages prog...

Clarion AutoPC Owner’s Manual 95 (Messages Command Words and Keys continued) Voice Manual ! ! Comment List … Press MENU , use to select List , then Hear available messages. Press MENU , use to select Lock, then Lock a message. To use Auto PC’s Messages, you need to set up wireless services so youcan...

Clarion AutoPC Owner’s Manual 96 Reviewing Messages When you receive a message, Messages alerts you with a tone (if audiblenotification is on), and with an asterisk over its icon on the Start menu. The summary information shown on the selection list is different for eachtype of message. For E-mail, ...

Clarion AutoPC Owner’s Manual 98 Voice Manual ! ! Comments Auto PC …Messages … Press Start , then to highlight Messages , then To select Messages program. Traffic …, or News …, or E-mail … To switch between Traffic,News, or E-mail. Pages areincluded under E-mail. Next … or Previous … To select the m...

Clarion AutoPC Owner’s Manual 99 Saving Messages To preserve important messages from being automatically deleted, youmay “lock” email, news, or traffic messages. Voice Manual ! ! Comments Auto PC …Messages … Press Start , then to highlight Messages , then To select Messages program. Press MENU , the...

Clarion AutoPC Owner’s Manual 100 Changing message storage options Because message content can quickly use all of the memory you haveavailable for data storage, you may want to specify how much of thememory you have allocated for data storage can be used for wirelesscontent. Manual ! ! Comments Pres...

Clarion AutoPC Owner’s Manual 101 Manual ! ! Comments Press Start , then to highlight Setup , then To access Setup program. to select Messages , then To select the Messages parameters. to select Storage Full Alert To select the Storage Full Alert parameter. to select On or Off To turn Storage Full A...

Clarion AutoPC Owner’s Manual 103 Chapter 10 – Using Voice Memo The Voice Memo program allows you to record and play your own voicememos. It also allows you to see the list of currently stored voice memosand to select a voice memo for playback or deletion. While you are recording a voice memo, Speec...

Clarion AutoPC Owner’s Manual 104 Recording voice memos You can record a voice memo while in any program using the V MEMObutton, or you may record a memo using the Voice Memo program. Recording a voice memo from any program Manual ! ! (Stop your vehicle to do manual steps) Comments Press V MEMO , li...

Clarion AutoPC Owner’s Manual 105 You may mute the CD player and the radio when your record or play backa memo. It’s your choice. Manual ! ! Comments Press Start , then to highlight Voice Memo , then To highlight and select Setup. Press MENU , then to highlight Mute On Record , then use to select On...

Clarion AutoPC Owner’s Manual 106 Recording a voice memo from Voice Memo program Voice Manual ! ! Comments Auto PC …Voice Memo … Press Start , then to highlight Voice Memo , then To highlight and select the VoiceMemo program, and enter it. Record … Press V MEMO Listen for the record prompt tonethen ...

Clarion AutoPC Owner’s Manual 107 Voice Manual ! ! Comments Auto PC …Voice Memo … Press Start , then to highlight Voice Memo , then To select the Voice Memoprogram. Open … Press MENU and to OPEN , then Display reads: “Building List …” then the list of memos. Example:Vmemo1: 15 s/84kB (15 secondsrequ...

Clarion AutoPC Owner’s Manual 108 Sorting Voice Memos Memos can be sorted by Date and by Name with the following results: Sorting options How memos are listed Date and Ascending Newest to oldest Date and Descending Oldest to newest Name and Ascending In alphabetical order Name and Descending In reve...

Clarion AutoPC Owner’s Manual 109 Voice Manual ! ! Comments Play … Press Plays currently loaded memo. Pause … Press Pauses playback, shows “Pause” in the display, leaves playbackindicator where memo was paused.If you want to playback from thepoint paused, say "Play" or press . Stop … Press i...

Clarion AutoPC Owner’s Manual 110 (Deleting a voice memo, continued.) Voice Manual ! ! Comments Yes … or No … to select Yes or No then to delete memo Unit “asks” if you want to deletethis memo. Either a voice ormanual command can be used. Voice Manual ! ! Comments Auto PC …Voice Memo … Press Start ,...

Clarion AutoPC Owner’s Manual 111 Manual ! ! Comments Press MENU and to Auto Delete Select the Delete After function. You will see onthe screen “Auto Delete: Never.” to choose from Never , 5 days , 15 days or 30 days This setting determines the length of time memoswill be kept in the memo store. Mem...

Clarion AutoPC Owner’s Manual 112 Manual ! ! Comments Press MENU and to Rename then Select the Rename function. You will see on thescreen the current name. Press to enter thefirst letter of the new name then to move to the next spaces and enter the remaining lettersto form the new name. (To cancel e...

Clarion AutoPC Owner’s Manual 113 The Clarion AutoPC System willaccept CF Cards from mostmanufacturers. Warning: the CFCard can be inserted one way only.Be sure to insert the CF Card withthe manufacturer’s label and arrow FACING RIGHT of the unit as shown below. Inserting the CF Card for export Make...

Clarion AutoPC Owner’s Manual 114 Manual ! ! Comments Press Start , then to highlight Voice Memo , then To highlight and select the Voice Memoprogram. Press MENU To select the MENU options. to Memo Store Select Memo Store. Press To change the memo store size for VoiceMemo. Manual ! ! Comments Press ...

Clarion AutoPC Owner’s Manual 115 Manual ! ! Comments Press MENU and to Mute On Play Select the Mute On Play function. You will seeon the screen “Mute On Play: Off.” to set On or Off This setting determines whether other audiosources will be muted during Voice Memoplayback. (Example: Radio.) Manual ...

Clarion AutoPC Owner’s Manual 117 Chapter 11 – Customizing Your Auto PC You can customize displays and add on new programs and hardware tomeet your information and entertainment needs on the road. Auto PC allows you to customize the screen for the way you use it. Theorder of the programs on the Star...

Clarion AutoPC Owner’s Manual 118 Manual ! ! (Stop your vehicle to do manual steps) Comments Press Start , then To select the program icon you want tomove. Press and hold number On the number keys, press and hold thenumber where you want the programicon. To go to the rest. If you have more than10 pr...

Clarion AutoPC Owner’s Manual 119 If you are having problems transferring information to or from your AutoPC and another mobile device powered by Windows CE, try adjusting theInfrared transfer speed. Manual ! ! Comments Press Start, then to highlight Setup , then To access Setup program. to select I...

Clarion AutoPC Owner’s Manual 120 Add or Change a Password Use a password to protect your data. A password is up to 4 numbers anda custom command word. Password protection is enabled after theignition is cycled off then on. Auto PC prompts you for a password thefirst time you enter protected program...

Clarion AutoPC Owner’s Manual 121 It is strongly recommended that you backup your custom data just in caseyou forget your password. Cold reboot is the only alternative forestablishing a new password if you have forgotten your password. Also,if your car battery fails or the unit’s coin battery fails,...

Clarion AutoPC Owner’s Manual 122 Manual ! ! Comments Press Start , then to highlight Setup , then To highlight and access Setup program. to select Password then To select Password parameter. Displayreads: “Provide password: …” Enter current password(up to 4 numbers), then to highlight Change Passwo...

Clarion AutoPC Owner’s Manual 123 Manual ! ! Comments Press Start , then to highlight Setup , then To highlight and access Setup program. to select Password then To select Password parameter. Displayreads: “Provide password: …” Enter current password,then to highlight Change Password Current passwor...

Clarion AutoPC Owner’s Manual 124 ASSIST The ASSIST function of the Clarion AutoPC system will provide you with many location-based services, including: emergency and roadsideassistance, vehicle security monitoring and tracking, remote door unlock,as well as operator-assisted directions and points o...

Clarion AutoPC Owner’s Manual 125 Changing Auto PC Sounds Auto PC permits you to change how the computer voice sounds, as wellas the beeps and other sounds the Auto PC makes. Manual ! ! Comments/Illustrations Press Start , then to highlight Setup , then To select the Setup program. to find Sounds an...

Clarion AutoPC Owner’s Manual 129 Speech Command options Auto PC “listens” and “speaks” to you. You can change the ways thatAuto PC does this through the following Speech Command options: Controls how much the volume of any audio output (such as the radioplaying) is lowered when Auto PC is listening...

Clarion AutoPC Owner’s Manual 130 Also, you may turn some command words off if you are not planning onusing them. This narrows the number of words Auto PC is recognizingand may be helpful if the Auto PC isn’t always understanding what yousay. Speech factors you can change Auto PC will not “listen” f...

Clarion AutoPC Owner’s Manual 131 Manual ! ! Comments/Illustrations Press Start , then to highlight Setup , then To select the Setup program. to Speech Commands , then Select Speech Commands program. to select Audio Mute Controls how much the volume of anyaudio output (such as the radio) is loweredw...

Clarion AutoPC Owner’s Manual 132 If Auto PC isn’t recognizing you when you say a given command word,you can train Auto PC to understand the way you say a word. You canalso add a custom command word to be used instead of the defaultcommand word. For example, you can add “Computer” as a wake-upword f...

Clarion AutoPC Owner’s Manual 133 To disable or enable the Wakeup word Manual ! ! Comments/Illustrations Press Start , then to highlight Setup , then Select the Setup program. to select Speech Commands and Select the Speech Commands program. to select Wakeup Word , and to choose On or Off Controls w...

Clarion AutoPC Owner’s Manual 134 Manual ! ! Comments/Illustrations Press Start , then to highlight Setup , then Select the Setup program. to select Speech Commands and Select the Speech Commands program. to select Global Commands and Select the Global Commands program. to select a current Global Co...

Clarion AutoPC Owner’s Manual 135 Alternative Global Commands 1. Mute 2. End 3. Clock 4. Setup 5. Audio 6. None Suppose you have no plans to use Volume, and also would like tosubstitute alternatives for Directions (Mute) and Messages (Clock). Manual ! ! Comments/Illustrations Press Start , then to h...

Clarion AutoPC Owner’s Manual 136 Changing Timeouts A timeout is the length of time that Auto PC waits for input beforereturning to its previous state. You can set the timeouts for key presses,speech command wakeup, and menus. Manual ! ! Comments/Illustrations Press Start , then to highlight Setup ,...

Clarion AutoPC Owner’s Manual 137 TimeoutName How long Auto PCwaits (your choice) Reason why Auto PC waits Hold keys for: .5, 1, 1.5, 2, 2.5 To activate the press-and-holdfunction on key presses. Listen for: 2, 5, 10, 15, 20, or Always See NOTE below For speech commands (afterthe last recognized spe...

Clarion AutoPC Owner’s Manual 139 Chapter 12 – Backup/Restore Caution: Do not turn off the ignition while doing Backup or Restore. Use the Backup/Restore program to protect the data you have stored onyour Auto PC. Backup/Restore protects all data customized by the userincluding the following: • Radi...

Clarion AutoPC Owner’s Manual 140 Using the CF Card for backup and restore The Clarion AutoPC System willaccept CF Cards from mostmanufacturers. Warning: the CFCard can be inserted one way only.Be sure to insert the CF Card withthe manufacturer’s label and arrow FACING RIGHT of the unit as shown bel...

Clarion AutoPC Owner’s Manual 141 Manual ! ! (Stop your vehicle to do manual steps) Comments Insert a CF Card into your AutoPC’s CF Card slot Make sure label and arrow arefacing right. Press Start , then to highlight Setup , then Select the Setup program. to Backup/Restore , then Select the Backup/R...

Clarion AutoPC Owner’s Manual 142 Manual ! ! Comments Insert the appropriate CF Card intoyour Auto PC’s CF Card slot Check date/time hand written onCF Card label before using. Press Start , then to highlight Setup , then Select the Setup program. to Backup/Restore , then Select the Backup/Restorepro...

Clarion AutoPC Owner’s Manual 143 Chapter 13 – Adding/Removing Software and Hardware Auto PC allows you to install new programs and hardware to utilizeadditional information and entertainment services while on the road. Auto PC provides automatic installation or removal of programs usingeither a CD ...

Clarion AutoPC Owner’s Manual 144 NOTE: The number of programs you can add may be limited by the amount of memory you have available in your Auto PC. Manual ! ! (Stop your vehicle to do manual steps) Comments Press Start , then to highlight Setup , then to see first Setup option To select and enter ...

Clarion AutoPC Owner’s Manual 145 Chapter 14 – Tips and Troubleshooting Tips This section provides tips about saying command words, protecting yourdata, and many other suggestions. Auto PC “listens” when you are speaking words decisively, as in acommand, and ignores words when you are talking normal...

Clarion AutoPC Owner’s Manual 146 • If you’ve set a timeout for Auto PC to stop listening, be sure to say Auto PC to wake up Auto PC before giving commands, or use the Push-To-Talk (PTT) button If Auto PC is still having problems understanding one or two commandwords, you may need to train Auto PC t...

Clarion AutoPC Owner’s Manual 147 If there is difficulty calculating a very complex route, try the following: • If you are using Local Roads, try using Fastest Route instead • Try to split the route into two or more routes You might not get a GPS signal in heavily built up urban areas, tunnels,or ro...

Clarion AutoPC Owner’s Manual 148 Types of data with examples Comment Satellites: 5 Number of satellites, 0 – 8. At least4 satellites are required for accurateGPS data. Latitude: 33.654 o Current location Longitude: -117.746 o Current location Altitude: +50 Feet Relative to system locale Time: 3:45:...

Clarion AutoPC Owner’s Manual 149 Once you get more familiar with entering information into your Auto PC,you may find it faster to use the numeric Keypad. You can use thenumeric Keypad to input or edit letters in the Radio and Address Bookprograms. Press a number key repeatedly to cycle through the ...

Clarion AutoPC Owner’s Manual 150 The cell phone dials only the numbers it gets from Address Book. If yourcellular phone provider requires that you dial a 1 or area code to completea call, you must enter numbers into Address Book in this format. When changing your cell phone cradle, you should remov...

Clarion AutoPC Owner’s Manual 151 Troubleshooting If you encounter difficulties while using your system, look here. Infrared transfer between Windows CE-based devices If you are unable to use infrared to transfer information between WindowsCE-based devices, try the following. 1. Transfer only one fi...

Clarion AutoPC Owner’s Manual 152 CAUTION: Do not remove the DCP or turn off the ignition while transferring data. Data discs (examples: computer CD-ROMs or the Navigation data discs)should not be placed in the CD changer. If data discs are placed in thechanger with no audio discs, the changer will ...

Clarion AutoPC Owner’s Manual 153 How to reboot the System Use reboot procedures in the following order: 1. Turn off the ACC power. 2. Remove the DCP. 3. If the system stops normal functions or cannot recognize peripherals, always try the Warm reboot first, as described on the next page. 4. If Warm ...

Clarion AutoPC Owner’s Manual 154 1. Warm reboot: • Push Reset Switch 1 (near the CD eject button) with the tip of a ball-point pen ora similar object. Note: All unsaved data in the open file will be erased. 2. Cold reboot: • Push and hold Reset Switch 2 first with a thin wire and, simultaneously pu...

Clarion AutoPC Owner’s Manual 155 How to handle a Start menu alert in Setup If an asterisk ( ) appears within the Start menu Setup icon, here is how to isolate the problem. Manual ! ! (Stop your vehicle to do manual steps) Comment Press Start , then to highlight Setup , and press Highlight the Setup...

Clarion AutoPC Owner’s Manual 157 Specifications Frequency Range: 87.9MHz to 107.9MHzUsable Sensitivity: 11dBfAlternate Channel Selectivity: 75dBStereo Separation (1kHz): 35dBFrequency Response (+/-3dB): 30Hz to 15kHz Frequency Range: 530 kHz to 1710kHzUsable Sensitivity: 28dB µ System: Compact disc...

Clarion AutoPC Owner’s Manual 158 Power Supply Voltage: 14.4V DC(10.8V to 15.6V allowable),Ground: negativeCurrent Consumption: Less than 10AExternal Dimensions: (Source unit) • 7"(width) x 2"(Height) x 6.1"(Depth) • [178(W) x 50(H) x 156(D) mm] External Dimensions: (Tuner Amp unit) • 7&...

Clarion AutoPC Owner’s Manual 159 Glossary A Address Book: The Auto PCprogram for managing contact(people) information. Audio: The Auto PC program usedto control the audio output settings. ASSIST: This button on theDetachable Control Panel connectsyou to roadside assistanceservices. NOTE: Requires a...

Clarion AutoPC Owner’s Manual 161 Index A Add or Change a Password, 68, 120 Adding a software application, 143Address Book, 55Address Book, speech commands, 56 ASSIST, 3, 67, 124, 159Audio adjustments, 51, 52Audio adjustments from CD Player program, 54 Audio adjustments from Radio program, 54 B Back...