Page 2 - DISCLAIMER
PNRIW Series Installation Instructions 2 DISCLAIMER Milestone AV Technologies, and its affiliated corporations andsubsidiaries (collectively, "Milestone"), intend to make thismanual accurate and complete. However, Milestone makes noclaim that the information contained herein covers all detai...
Page 3 - DIMENSIONS; PNRIW SHOWN IN PAC-501
Installation Instructions PNRIW Series 3 DIMENSIONS 30.00 762 20.00 508 10.00 254 10.00 254 15.00 381 15.00 381 C/L OF 14" MOUNTING PATTERN PNRIW SHOWN IN PAC-501 WHICH MUST BE ORDERED SEPARATELY .62 ADDED DEPTH WHEN RETRACTED 16 3.63 NOTE: PSBU INTERFACE BRACKET NOT SHOWN. THE PSBU INTERFACE BR...
Page 4 - LEGEND; Tighten Fastener
PNRIW Series Installation Instructions 4 DIMENSIONS (CONT’D) LEGEND DIMENSIONS: [MILLIMETERS] INCHES Tighten Fastener Apretar elemento de fijación Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Loosen Fastener Aflojar elemento de fijació...
Page 5 - TOOLS REQUIRED FOR INSTALLATION AND PARTS; [PSBU interface bracket
Installation Instructions PNRIW Series 5 TOOLS REQUIRED FOR INSTALLATION AND PARTS (3/16") (9/16") K (1) 3/16" A (1) G (4) F (16) H (4) M (12) L (1) J (1) B (4) [Trim - 2 short (SIDES) - 2 long] D (4) 5/16" C (4) 5/16-18 x 5/8" E (4) 5/16" [Swing arm mount assembly] N (1) [PS...
Page 6 - INSTALLATION; IMPROPER INSTALLATION CAN LEAD TO; Figure 1; Upper mounting bracket
PNRIW Series Installation Instructions 6 INSTALLATION The following procedure assumes that a Chief Listed ModelPAC501 In-Wall accessory has previously been installed usingthe installation instructions and hardware provided with thePAC501. If a PAC501 is not installed or there are any otherquestions ...
Page 7 - Display Installation; Figure 4; Holes are provided in the faceplate for use with a; Figure 5; A padlock or bolt may
Installation Instructions PNRIW Series 7 Display Installation WARNING: IMPROPER INSTALLATION CAN LEAD TO MOUNT FALLING CAUSING SEVERE PERSONAL INJURYOR DAMAGE TO EQUIPMENT! DO NOT install display in amanner other than that specified by the manufacturer. Certaindisplays may require the use of an inte...
Page 8 - Cable Management; Figure 6
PNRIW Series Installation Instructions 8 Cable Management 1. Attach all cables to display. 2. If necessary, use cable tie mounts (G) and cable ties (M) tosecure cables within PAC501. WARNING: IMPROPER INSTALLATION CAN LEAD TO SERIOUS PERSONAL INJURY OR DAMAGE TOEQUIPMENT! Make sure cables do not run...
Page 9 - Tension Adjustments; Pitch Tension Adjustment; Figure 8; Pitch
Installation Instructions PNRIW Series 9 Tension Adjustments Pitch Tension Adjustment 1. With display mounted, check for desired Pitch tension. 2. If required, adjust the Centris Select TM knob right or left until desired pitch tension is obtained. (See Figure 8) 3. To lock the mount at the desired ...
Page 10 - Swivel Tension Adjustment
PNRIW Series Installation Instructions 10 Swivel Tension Adjustment CAUTION: DO NOT OVER TIGHTEN SWIVEL ADJUSTMENT NUT. Over tightening swivel adjustment nutwill cause excessive wear and may distort adjustmentcomponents. 1. Using a 9/16” wrench (not provided), slightly tighten orloosen swivel tensio...
Page 11 - Removing Display from Mount
Installation Instructions PNRIW Series 11 2. Use the adjustment wrench (L) provided with the mount,and turn adjustment insert clockwise to increase swing armtension (See Figure 13) or counterclockwise to reduceswing arm tension. (See Figure 13) NOTE: Small adjustments of 1/8 turn or less are typical...
Page 12 - Europe; Franklinstraat 14, 6003 DK Weert, Netherlands; Asia Pacific; PNRIW Series
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344 P 800.582.6480 / 952.225.6000 F 877.894.6918 / 952.894.6918 Europe A Franklinstraat 14, 6003 DK Weert, Netherlands P +31 (0) 495 580 852 F +31 (0) 495 580 845 Asia Pacific A Office No. 918 on 9/F, Shatin Galleria18-24 Shan Mei Street...
