Char-Broil 463232011 - Manuals

WARNING If “growing” bubbles appear do not use or move the LP cylinder. Contact an LP gas supplier or your fire department! Connecting Regulator to the LP Cylinder 1. LP cylinder must be properly secured onto grill. (Refer to assembly section.) 2. Turn all control knobs to the OFF position. 3. Turn ...

6. Turn the coupling nut clockwise and tighten to a full stop. The regulator will seal on the back-check feature in the LP cylinder valve, resulting in some resistance. An additional one-half to three-quarters turn is required to complete the connection. Tighten by hand only – do not use tools. NOTE...

7 WARNING For Safe Use of Your Grill and to Avoid Serious Injury:• Do not let children operate or play near grill. • Keep grill area clear and free from materials that burn. • Do not block holes in sides or back of grill. • Check burner flames regularly. • Use grill only in well-ventilated space. NE...

8 Burner Flame Check • Remove cooking grates and flame tamers. Light burners, rotate knobs from HI to LOW . You should see a smaller flame in LOW position than seen on HI . Perform burner flame check on sideburner, also. Always check flame prior to each use. If only low flame is seen refer to "S...

9 Cleaning the Burner Assembly Follow these instructions to clean and/or replace parts of burnerassembly or if you have trouble igniting grill.1. Turn gas OFF at control knobs and LP cylinder. 2. Remove cooking grates and flame tamers. 3. Remove carryover tubes and burners. 4. 5. Carefully lift each...

This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated...

PARTS LIST NOTE: Some grill parts shown in the assembly steps may differ slightly in appearance from those on your particular grill model. However, the method of assembly remains the same. 11 Key Qty Description A 1 BOTTOM SHELF B 1 TANK SCREW , F/ BOTTOM SHELF C 2 CASTER, LOCKING D 2 CASTER, FIXED ...

2 1/4-20x1/2” screw 1 Attach side panels to bottom shelf using three 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers per panel. IMPORTANT: Panel with large hole mustbe on left side of bottom shelf. 7mm lock washer 7mm flat washer Locking caster Bottom shelf Non-lock caster Rear Front Left...

3 4 This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart, aligning slots at bottom of grill head with posts on cart side panels. Make sure the regulator hose is hanging outside the cart. Grill head must face open side of cart. Place lo...

On back of grill, place upper back panel between side panels and above lower back panel. Secure upper back panel, in lower holes, using one 1/4-20x1½” screw, 7mm lock washer, and 7mm flat washer on each side. Do not fully tighten screws until side shelf installation is complete in later steps. 5 15 ...

16 6 Insert flange on right side shelf into side shelf brackets on side of firebox, shown B . flat washer, shown E. Attach front of shelf and fascia using one #8x3/8” self-tapping screw and large Attach front of shelf and fascia using one 1/4”-20x3/4” screw, 7 mm lock washer, 7 mm flat washer and 1/...

9 24 Pull out the three knobs from control panel. Insert temperature gauge stem into the biger hole above knob bezel,shown A . Make the temperature gauge attached on the panel. Push the temperature gauge downward till it clips on the panel, shown B/C . Re-install the three knobs. Knob Knob bezel Tem...

10 11 Insert sideburner burner into left shelf. shelf, shown A . The stud on bottom of burner fits into rear small hole in sideburner drip pan on Secure burner to sideburner drip pan with one Wing nut, shown B . Make sure burner tube engages sideburner valve, shown C . B 19 A Sideburner burner Sideb...

*This side UP Tank heat shield 13 12 Inside of cart, insert rear shield tab into left slot on upper of lower back panel. Attach front shield tabs under front brace and attach right and Insert left and right grease tray rails into slots left rails under front brace with three #8x3/8” self-tapping scr...

14 15 Insert hinge pin on bottom of doors into hole in bottom shelf. Press upper hinge pin in front brace, align hinge hole on top of door, and release hinge pin into door. Hinge pin on bottom of door Top of door PRESS 21 Left door Right door Connect each of the wires from the main burner electrodes...

16 22 Install flame tamers by sliding one end of each flame tamer into slots at front of firebox and resting opposite end on pins in back of firebox. Back of firebox Front of firebox Note: Some parts omitted for clarity of illustration Flame tamers Pin 17 Place cooking grates onto the firebox as sho...

On back of grill, slide grease tray into opening in upper back panel. CAUTION Failure to install grease tray will cause hot grease to drip from bottom of grill with risk of fire or property damage. 18 23 Unscrew on cart right side panel. Insert AA battery into ignitor, negative (—) end first. Replac...

– 24 20 LP CYLINDER IS SOLD SEPARATELY. Fill and leak check the cylinder before attaching to grill and regulator (see Use & Care section). Once cylinder has been filled and leak checked, place cylinder into hole in bottom shelf. Make sure cylinder valve is facing front of grill. Secure cylinder ...

EMERGENCIES: If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Emergencies Problem Gas leaking from cracked/cut/burned hose. Gas leaking from LP cylinder. Gas leaking from LP cylinder valve. Gas leaking between LP cylinder and regulator connection. Fire ...

Troubleshooting ( continued ) Problem Burner(s) will not light using ignitor.(See Electronic Ignition Troubleshooting also) Burner(s) will notmatch light. Sudden drop in gasflow or low flame. Flames blow out. Flare-up. Persistent grease fire. Flashback...(fire in burner tube(s)). Unable to fill LP c...

Troubleshooting - Electronic Ignition Problem (Ignition) SECTION I No sparks appear at any electrodes when Electronic Ignition Button is pressed; no noise can be heard from spark module. SECTION II SECTION III Sparks are present but not at all electrodes and/or not at full strength Possible Cause • ...