Central Pneumatic 40115 - Manuals

Page 2 - powered tools in the presence of flammable gases or liquids.

SKU 97525 40115 Page 2 For technical questions, please call 1-800-444-3353. Specifications Air Inlet 1/4” - 18 NPT Recommended Air Pressure 60 - 100 PSI, 100 PSI Max. Magazine Capacity 100 Nails or 80 Staples Safety Feature Single Sequential Safety Trip Mechanism Nail Size .039-.042” Shank (18 Gauge...

Page 3 - Do not operate tool if under the influence of alcohol or drugs

SKU 97525 40115 Page 3 For technical questions, please call 1-800-444-3353. 8. Use eye and ear protection . Always wear ANSI-approved impact safety goggles and appropriate hearing protection. Wear a full face shield if you are producing metal filings or wood chips. Wear a NIOSH-approved dust mask or...

Page 4 - Do not fire fasteners too close to the edge of a workpiece

SKU 97525 40115 Page 4 For technical questions, please call 1-800-444-3353. heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the tool. Check your air compressor’s manual for the appropriate size cord. It is also possible that the use of an extension ...

Page 5 - Unpacking; manual as soon as possible.; Testing The Single Sequential Safety Trip Mechanism; the nailer/Stapler at a piece of scrap wood when testing.; Make sure the tool is disconnected from the air supply.; Operation; air pressure of 100 PSI.

SKU 97525 40115 Page 5 For technical questions, please call 1-800-444-3353. Unpacking When unpacking, check to make sure the parts listed on page 9 are included. If any parts are missing or broken, please call Harbor Freight Tools at the number on the cover of this manual as soon as possible. Testin...

Page 6 - Loading Nails or Staples; ALWAYS WEAR ANSI APPROVED IMPACT SAFETY GOGGLES WHEN; Operating the Stapler/Nailer; Do not fire repeatedly

SKU 97525 40115 Page 6 For technical questions, please call 1-800-444-3353. 3. Empty the magazine of nails or staples.4. Check that the Trigger (38) and the Safety (42) on the nose of the tool, move freely, without sticking. 5. Connect the air supply to the tool at the Air Plug (77) and set at the r...

Page 7 - Anytime; any; disconnected and is incapable of firing any staples.; Clearing Jams; Figure 1; FIGURE 1

SKU 97525 40115 Page 7 For technical questions, please call 1-800-444-3353. Anytime any maintenance or repairs are done (including clearing jams), FIRST: 1. Disconnect the Nailer/Stapler from the air hose.2. Empty Magazine A (61) completely. 3. Attempt to fire the Nailer/Stapler into a piece of scra...

Page 8 - Troubleshooting Guide; Problem

SKU 97525 40115 Page 8 For technical questions, please call 1-800-444-3353. Troubleshooting Guide Stop using the Nailer/Stapler immediately if any of the following problems occur. Repairs and part replacements must be done only by a qualified technician. All procedures in bold on this chart are to b...

Page 9 - Maintenance; Parts List

SKU 97525 40115 Page 9 For technical questions, please call 1-800-444-3353. Maintenance Warning! Always disconnect the tool from the air compressor and then empty the magazine of nails or staples before attempting to inspect or perform maintenance to the Nailer/ Stapler. 1. Inspect all of the nuts a...

Page 10 - Assembly Drawing

SKU 97525 40115 Page 10 For technical questions, please call 1-800-444-3353. Assembly Drawing NOTE : Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts.

Page 11 - LIMITED 1 YEAR WARRANTY; MERCHANTABILITY AND FITNESS.

SKU 97525 40115 Page 11 For technical questions, please call 1-800-444-3353. LIMITED 1 YEAR WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in ma...