Central Pneumatic 30224 - Manuals

Page 2 - Troubleshooting section at end of manual.; Contents; Unpacking

For technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. SKU 30224 Page 2 Contents Unpacking ....................................................................................................... 2 Specifications ...................................................

Page 6 - Air Connection; FIGURE 1; Control Layout

For technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. SKU 30224 Page 6 Air Connection For best service you should incorporate a regulator and inline filter, as shown in the diagramabove. Hoses, couplers, regulators, and filters are all available at Harbor Fre...

Page 7 - Preparation; Start the air compressor.; A Comparison: Conventional versus HVLP Spray Guns; See

For technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. SKU 30224 Page 7 Preparation Note: Proper paint material mixture helps to ensure less problems. Be sure to follow the manufacturer’s directions. Most materials will spray readily if they are thinned proper...

Page 8 - Fan Direction and Pattern Adjustment; Never exceed the Maximum Inlet PSI of 80 PSI.

For technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. SKU 30224 Page 8 Fan Direction and Pattern Adjustment Fan Direction To change the direction of the fan from horizontal to vertical, loosen the Lock Ring andturn the Air Cap (1S) 90 degrees. After the adjus...

Page 9 - on; FIGURE 5; Fan Direction and Pattern Adjustment (continued)

For technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. SKU 30224 Page 9 3. Turn the Fluid Control Knob (29) clockwise until it is fully closed. See FIGURE 1 on page 6. 4. After setting up a piece of scrap material, squeeze the Trigger (38) in short bursts whil...

Page 10 - Techniques; Always keep the gun at right angles to the workpiece (See; FIGURE 6

For technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. SKU 30224 Page 10 2. To ensure you don’t allow paint to build up, start moving the Spray Gun before youSqueeze the Trigger (38). When you are finished spraying, release the Trigger (38)before you stop movi...

Page 11 - Maintenance

For technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. SKU 30224 Page 11 Maintenance SOLVENT SELECTION Always follow the paint manufacturer’s recommendations for cleaning, solvent type, and disposing of used solvent. Latex Paints: Use warm, soapy water. IMPORT...

Page 12 - Parts List; PLEASE READ THE FOLLOWING CAREFULLY

For technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. SKU 30224 Page 12 NOTE : Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. Parts List PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTU...

Page 13 - Assembly Diagram

For technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. SKU 30224 Page 13 Assembly Diagram

Page 14 - Troubleshooting; Spray Pattern Diagnosis; The Patterns below

For technical questions, please call 1-800-444-3353. SKU 30224 Page 14 If the steps above do not solve the problem or if the repairs involved are too complex, contact a qualified technician. IMPORTANT: Improper cleaning is a common reason for the unit not to work properly.Most problems can be avoide...

Page 15 - Problem

For technical questions, please call 1-800-444-3353; Troubleshooting section at end of manual. SKU 30224 Page 15 Troubleshooting (continued) 1. Low material level2. Cup tipped too far3. Clogged Air Vent4. Loose fluid inlet connections5. Dry or loose fluid needle Packing Nut6. Loose/damaged fluid tip...

Page 16 - 0 Day Warranty

Page 20 For technical questions, please call 1-800-444-3353. SKU 67450 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and wo...