Cecilware C-2003G-IT - Manuals

Page 2 - RECOMMENDED COFFEE AMOUNT FOR BREWING

2 SPECIFICATIONS ELECTRICAL SPECIFICATIONS MODEL NO. C-2003G-IT C-2003RG-IT C-2003LG-IT Volts 120 120 120 Watts 1,800 1,800 1,800 Amps 15 15 15 Wall Outlet (Receptacle) 5-15R 5-15R 5-15R All Brew Centers are single phase with 2 wires plus a ground with cord and plug, except Eport 220V, 1 PH, 50 cycl...

Page 3 - operation and aid in identifying potential problems.

3 FEATURES AND BENEFITS OF THE DIGITAL, MEMBRANE CONTROL TOUCH PAD BREWER 1. 100% Solid State Control for improved reliability. 2. Modular design and reduced component count for ease of service. 3. Optional Low Water Temperature Lockout to prevent dispensing at water temperatures below an adjustable...

Page 4 - INSTALLATION AND OPERATING INSTRUCTIONS

4 INSTALLATION AND OPERATING INSTRUCTIONS Warranty is void if the Brewer is connected to any Voltage other than the Voltage specified on the data label of the Brewer. UNPACKING AND INSPECTION Carefully unpack the Brewer by cutting the straps and lifting the carton off the Brewer. ASSEMBLY AND SET-UP...

Page 5 - of the; LCD WINDOW............

5 NG34A-E CAUTION HOT WATER D:\ 1- Mi lt \L abel s & Logo s\ Techno copy.tif PROGRAMMING INSTRUCTIONS The following is a Functional Description of the Single Station Brewer : Modes of Operation - Overview Initialization Mode – This mode is only active during the first few seconds after a “power-...

Page 6 - MODES OF OPERATION – DESCRIPTIONS; Initialization Mode:; The following screen signifies the presence of this mode:; Filling State; first fill; Waiting State

6 MODES OF OPERATION – DESCRIPTIONS Initialization Mode: The following screen signifies the presence of this mode: CECILWARE &&&&& REV #.# Description – This mode is active only during the first few seconds after “power-on”. The purpose of the Initialization Screen is to identify...

Page 7 - Brewing State; BREWING DDD K; Brew Fill Constant Calibration State; Description; Warmers; Description –; Refer to the Service Mode Descriptions for more

7 Brewing State BREWING DDD K MM:SS HH:MMP Description – This screen is displayed when a Brew Cycle is in progress. The time remaining in the Brew Cycle is displayed in the lower left-hand corner of the screen (depicted as “MM:SS”). The Brew Key LED will blink in this state. The Main Warmer is autom...

Page 8 - SERVICE MODE; Modified parameters are saved upon scrolling to a different menu.

8 SERVICE MODE Description – The main function of Service Mode is to give qualified personnel the ability to configure the system to meet the requirements of each installation. General Conventions (unless otherwise indicated) 1) To enter or exit Service Mode simultaneously depress both the hidden ke...

Page 12 - ERROR MODE; the initial application of power to the system. This test is

12 ERROR MODE Description – The main function of Error Mode is report any system malfunctions and to disable the unit The system must be “powered down” using the Power Key located on the membrane keypad to reset any reported error. KEYPAD ! SYSTEM ERROR ! KEYPAD Description – This screen is displaye...

Page 14 - TOP CABIN OPEN VIEW

14 TOP CABIN OPEN VIEW 24 23 29 28 25 26 19 20 21 22 32 31 30 27

Page 16 - TROUBLESHOOTING GUIDE; proper; PROBLEM

16 TROUBLESHOOTING GUIDE WARNING: To reduce the risk of electrical shock unplug the dispenser power cord before repairing or replacing any internal components of the unit.. Before any attempt to replace a component be sure to check all electrical connections for proper contact PROBLEM PROBABLE CAUSE...

Page 17 - SPECIAL COMPONENTS TEST AND ADJUSTMENTS

17 SPECIAL COMPONENTS TEST AND ADJUSTMENTS 1) WATER INLET VALVE (SOLENOID) TEST ( Located inside bottom cabin ) Turn power off from touchpad. If the water level rises inside the tank, and shoots out of the overflow, the Water Inlet Valve is leaking. Disconnect wires from the Water Inlet Valve coil a...

Page 18 - SINGLE DISPENSE VALVE; brew; CLEANING AND SANITIZING; To prepare a sanitizing solution:

18 5) CHECK DISPENSE VALVES FOR LIME BUILD-UP ( Located inside top cabin ) Drain The Water Tank To Just Below The Level Of The Dispense Valves. Remove The Valves And Clean. You Can Take These Valves Apart By Hand As Shown. Replace The Assembly As Needed. Replace The Valve Into The Tank And Refill ta...

Page 19 - CECILWARE CORPORATION

19 #1 100W CECILWARE CORPORATION ELECTRICAL DIAGRAM C-2003G-IT 120V (3 BURNERS) L1 BERG CONNECT0RS TITLE: REV BY DATE P2 LEDS P5 K EYS DESCRIPTION KEYPAD SINGLE NG34A N 120V INPUT C1 0.1uf 275V SP1 LEVEL PROBE THER- MISTOR L617A TANK HEATER TEE ASS'Y K681A G MT1 MT2 OVERFLOW HOSE #2 100W HTR #3 100W...