Capresso 156 - Manuals - manualsarea.com

Page 2 - IMPORTANT SAFEGUARDS; putting on or taking off parts, and before cleaning the appliance.; SAVE THESE INSTRUCTIONS; SPECIAL CORD SET INSTRUCTIONS; becoming entangled in or tripping over a long cord.

IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always befollowed, including the following: 1. Read all instructions. 2. Do not touch hot surfaces. Use handles or knobs. 3. To protect against fire, electric shock and injury to persons, do not immerse cord, plug...

Page 3 - Traces of Coffee Grounds; Grinder was tested during

1. Height-Adjustable Coffee Spout1a. Sticker with Serial Number1b. Door 1c. Program Dial with "P BUTTON"2. Two Line Display (see fig. 3)3. Removable Water Tank4. Low Water Flotation Device (see fig. 4, call-out #4)5. CLARIS Water Care Cartridge (installed)6. Hinged Water Tank Lid7. Ground Co...

Page 9 - BLUE; HOT WATER CYCLE / NECESSARY

All Display Messages are shown in BLUE 7. Preparing the Machine Place the machine on a level surface and remove the water tank (fig. 4).Remove all accessories from the water tank. Plug in machine. Make sure the Steam/Water Dial points to the 0-position (fig. 2a). Filling the Water Tank • Rinse water...

Page 10 - Please note: When selecting the option

BUTTON (fig.1, 10a) again. The second line of the display will show BREWING 3.0. The C1300 will start grinding and brewing. Since it is the first time, it will not complete the cycle. When the display shows again PRESS BUTTON , repeat step "e" one more time. Discard the coffee. f. Now the gr...

Page 11 - Frothing and Steaming

Important: As long as the C1300 grinds, brews or discards coffee, do NOTattempt to pull out the drawer. This can seriously damage your machine. Seechapter 13. 8.1 Using Pre-ground Coffee You can also use pre-ground coffee, bypassing the grinder. This comes in handyif someone requests decaf, sugar co...

Page 12 - Heating and Frothing Milk; will show; Cleaning the Frother

8.4 Heating and Frothing Milk a. Turn the SW Dial from the 0-position to the steam position (fig. 2b). The display will show HEATING UP (this takes about 15 to 25 seconds). b. Add cold milk to a pitcher or a cup. c. The display will now show STEAM READY / PRESS BUTTON . d. Immerse the tip of the fro...

Page 13 - • Replace the black tip and screw it on finger tight.; Automatic Monitoring Controls; The C1300 is heating up. Wait until a different message appears.

• Replace the black tip and screw it on finger tight. Note: There is also an extra black tip included with the machine, just in caseyou lose the first one. 9. Automatic Monitoring Controls The C1300 has automatic monitoring controls. The display will show whencleaning, refilling and any other mainte...

Page 14 - TEMPERATURE / REGULAR; Changing the Language

10. Changing Parameters Besides the six different coffee options and the cup sizes you can change avariety of parameters as explained in chapters 10.1 through 10.6. 10.1 Changing the Grinder Fineness Important: You can only adjust the fineness during the actual grinding process.For darker beans, we ...

Page 15 - Changing the Water Hardness; LEVEL; Claris Water Cartridge

10.6 Changing the Water Hardness Turn the Program Dial to Pos. 7. The display shows HARDNESS / LEVEL 2. Pushing the P Button repeatedly shows the following options (second line ofdisplay): LEVEL – , LEVEL 1, LEVEL 2, LEVEL 3, LEVEL 4, FILTER. The C1300 gives you the following options with regards to...

Page 16 - Installing and Activating the Claris Water Filter Cartridge; shows; Replacing the CLARIS Cartridge; REPLACE FILTER; General Cleaning Instructions; for cleaning this funnel.

11.1 Installing and Activating the Claris Water Filter Cartridge Important: Never install the cartridge before or during "Preparing Machine ForThe First Time."Make sure the C1300 is on and ready to make coffee.a. Remove the cartridge from its bag and rinse under cold running water.b. Open th...

Page 18 - How to Decalcify

will show: TABLET CLEANING / IN PROGRESS . The machine will run a few hot water rinsing cycles. After approx. 2 minutes the display shows: EMPTY TRAY . g. Remove tray, empty it and replace. The display will now show SET P DIAL / TO POS. 1. Set the Program Dial to position 1. You can now continue bre...

Page 19 - Clearing for Transport

e. Now press the P Button. The display will show: PLACE LARGE CUP / UNDER FROTHER alternating with PRESS P BUTTON. f. Place a large cup under the steam nozzle. The cup or container should have a capacity of 12 oz. Press the P Button. The display will read DECALCIFYING / IN PROGRESS . For the next fe...