Bush Hog 3860 QT - Manuals

IMPORTANT SAFETY PRECAUTIONS This symbol is used to call attention to safe-ty precautions that should be followed by the operator to avoid accidents. When you see this symbol, carefully read the message that follows and heed its advice. Failure to comply with safety precautions could result in serio...

10. Before disconnecting hydraulic lines, relieve all hydraulic pressure. 11. Do not tamper with the relief valve setting. The relief valve is pre-set at the factory. Changing the setting can cause overloading the loader and tractor and serious operator injury may result. 12. Always wear safety gogg...

IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONS. *(This section is intended to explain in broad terms the concept and effect of the following federal laws and regulations. It is not intended as a legal interpretation of the laws and should not be considered as ...

1. INTRODUCTION AND DESCRIPTION INTRODUCTION We are pleased to have you as a Bush Hog cus-tomer. Your Front End Loader has been carefullydesigned to give maximum service with minimumdown time. This manual is provided to give you thenecessary operating and maintenance instructionsfor keeping your fro...

Model 3860 QT Technical Specifications G E J C B A H F D 8 A. Maximum Lift Height - Measured at Pivot Pin . . . .176" B. Maximum Lift Height - Under Level Bucket . . . . . 170" C. Clearance with Attachment Dumped 45º . . . . . . . 148" D. Reach at Maximum Height . . . . . . . . . . . . ....

2. INSTALLATION INSTRUCTIONS 9 CAUTION E Q U I P Y O U R T R A C T O R W I T H A R O P SCAB OR FRAME FOR YOUR PROTECTION.SEE YOUR TRACTOR/ROPS OPERATORM A N U A L F O R C O R R E C T S E A T B E L TUSAGE. Read entire instructions before beginning to installthe loader. Personal injury and machine dam...

CAUTION DO NOT STAND, WALK OR WORK UNDERA R A I S E D L O A D E R O R A T T A C H M E N TUNLESS IT IS SECURELY BLOCKED ORHELD IN POSITION. ACCIDENTAL MOVE-MENT OR A CONTROL LEVER/LEVERS ORL E A K S I N T H E H Y D R A U L I C S Y S T E MCOULD CAUSE THE LOADER TO DROP,O R A T T A C H M E N T T O D U ...

6. DISMOUNTING THE LOADER CAUTION ALWAYS PARK LOADER WITH MATERIALB U C K E T O R A U T H O R I Z E D B U S H H O GATTACHMENT ATTACHED TO THE LOADER. BEFORE LEAVING THE TRACTOR SEAT,LOWER ATTACHMENT OR LOADER BOOMT O G R O U N D , S T O P E N G I N E , L O C KBRAKES, RELIEVE HYDRAULIC PRESSUREAND RE...

Reinstall hinge assemblies, rear hinge pins, andsnap pins to loader for storage. Disconnect thehoses at the quick couplers. Start the tractor. Slowlyback the tractor away from the loader. Refer toFigure 8. Figure 8 IMPORTANT: To avoid hydraulic hose damage,be alert and make sure hoses do not catch o...

8. INSTALLATION & OPERATION OF QUICK DRAW LATCH ATTACH ALWAYS READ AND FOLLOW OPERAT-ING INSTRUCTIONS BEFORE OPERATINGQUICK DRAW LATCH ATTACH. WARNING INSTALLATION INSTRUCTIONS IMPORTANT: Do not extend bucket cylindersw i t h o u t q u i c k d r a w l a t c h a t t a c h i n s t a l l e d o nloa...

11. BUCKET ATTACHMENT QUICK DRAW BUCKET IMPORTANT: Refer to pages 29 & 30 for instruc-tions concerning Installing Attachment to QuickDraw Latch Attach. IMPORTANT: Refer to page 31 for instructionsconcerning Removing Attachment from QuickDraw Latch Attach. Quick draw buckets are available as foll...

12. SUPER PENETRATOR BALE PROBE ATTACHMENT IMPORTANT: It is not recommended that loaderb e d e t a c h e d f r o m t r a c t o r w i t h b a l e p r o b eattached. Loaders will park safely, however, baleprobe could be damaged during parking. Alwaysd e t a c h l o a d e r w i t h b u c k e t o r o t ...

13. DOZER ATTACHMENT CAUTION T O H E L P P R E V E N T B O D I L Y I N J U R Y ,A L W A Y S P A R K A N D S T O R E D O Z E RATTACHMENT WITH PARKING STANDS INPARKED POSITION. I M P O R T A N T : D o n o t p a r k l o a d e r w i t h d o z e rattachment attached. Always detach loader withbucket or ot...

15. PALLET FORK ATTACHMENT CAUTION F O R K T I N E S M U S T B E A D J U S T E D O U T -W A R D A N D L O C K E D B E H I N D P A R K I N GANGLES BEFORE PARKING LOADER. NEVER OPERATE PALLET FORKS WITH-OUT GUARD ASSEMBLY INSTALLED. TO AVOID SERIOUS INJURY OR DEATH: ★ N E V E R L I F T L A R G E R O U...

16. GRAPPLE ATTACHMENT INSTALLATION INSTRUCTIONS IMPORTANT: Refer to pages 29 & 30 for instruc-tions concerning Installing Attachment to QuickDraw Latch Attach. IMPORTANT: Refer to page 31 for instructionsconcerning Removing Attachment from QuickDraw Latch Attach. A four tine, two cylinder grapp...

NOTICE SUPPLEMENTAL INSTRUCTIONS FOR FORD GENESIS SPECIAL Refer to Form BHF 1820 Packing List and Installation Instructions includ- ed with your BHF 82356 Mounting Kit for detailed Operation Instructions specific for this Loader. 40

SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damagescan occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, providesafety decals for any of our products in the field at no charge. Contac...

CAUTION 1. USE ONLY FACTORY SUPPLIED CLEVIS AND MOUNTING HARDWARE WHEN ATTACHING TO CLEVIS MOUNTING POINT OF BUCKET. 2. MAXIMUM LOAD LIMIT ON FACTORY CLEVIS AND CLEVIS MOUNTING POINT IS 6500 POUNDS. 3. NEVER TOW ANY POINT OF THE LOADER WITH A CHAIN, ROPE, OR CABLE.4. DO NOT APPLY TRACTOR PULL OR PUS...

TORQUE SPECIFICATIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* BOLT DIAMETER WRENCH (IN.) “B” AND SAE SAE SAE SIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 1...